@@ -858,7 +858,10 @@ static void ax88179_set_multicast(struct net_device *net)
struct ax88179_data *data = dev->driver_priv;
u8 *m_filter = ((u8 *)dev->data);
- data->rxctl = (AX_RX_CTL_START | AX_RX_CTL_AB | AX_RX_CTL_IPE);
+ data->rxctl = (AX_RX_CTL_START | AX_RX_CTL_AB);
+
+ if (NET_IP_ALIGN)
+ data->rxctl |= AX_RX_CTL_IPE;
if (net->flags & IFF_PROMISC) {
data->rxctl |= AX_RX_CTL_PRO;
@@ -1424,7 +1427,7 @@ static int ax88179_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
/* Check CRC or runt packet */
if ((*pkt_hdr & (AX_RXHDR_CRC_ERR | AX_RXHDR_DROP_ERR)) ||
- pkt_len < 2 + ETH_HLEN) {
+ pkt_len < (NET_IP_ALIGN ? 2 : 0) + ETH_HLEN) {
dev->net->stats.rx_errors++;
goto advance_data_ptr;
}
@@ -1438,8 +1441,13 @@ static int ax88179_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
}
skb_trim(ax_skb, pkt_len);
- /* Skip IP alignment pseudo header */
- skb_pull(ax_skb, 2);
+ if (NET_IP_ALIGN) {
+ /* Skip the pseudo header, 2 bytes at the start of each
+ * ethernet frame, resulting from hardware 4-byte
+ * IP header alignment (triggered by AX_RX_CTL_IPE)
+ */
+ skb_pull(ax_skb, 2);
+ }
ax_skb->truesize = SKB_TRUESIZE(pkt_len);
ax88179_rx_checksum(ax_skb, pkt_hdr);
@@ -1609,8 +1617,10 @@ static int ax88179_reset(struct usbnet *dev)
ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_TXCOE_CTL, 1, 1, tmp);
/* Configure RX control register => start operation */
- *tmp16 = AX_RX_CTL_DROPCRCERR | AX_RX_CTL_IPE | AX_RX_CTL_START |
+ *tmp16 = AX_RX_CTL_DROPCRCERR | AX_RX_CTL_START |
AX_RX_CTL_AP | AX_RX_CTL_AMALL | AX_RX_CTL_AB;
+ if (NET_IP_ALIGN)
+ *tmp16 |= AX_RX_CTL_IPE;
ax88179_write_cmd(dev, AX_ACCESS_MAC, AX_RX_CTL, 2, 2, tmp16);
*tmp = AX_MONITOR_MODE_PMETYPE | AX_MONITOR_MODE_PMEPOL |
Problem Description: According to the comments in the hardware vendor's outdated source code [1], AX_RX_CTL_IPE signals the hardware to do 32-bit(4-byte) IP header alignment; such alignment is equivalent to the concept of NET_IP_ALIGN = 2 (an extra 2-byte "pesudo header" at the beginning of each etherner frame), as described in skbuff.h. In the current implementation, however, AX_RX_CTL_IPE is always enabled regardless of the value of NET_IP_ALIGN; this can introduce waste in many aspects, such as 1. hardware internal resource 2. USB bandwidth 3. host memory 4. cpu cycles (for updating frame start pointers and frame size variables) when alignment is completely unnecessary, i.e. NET_IP_ALIGN = 0. Solution: Enable AX_RX_CTL_IPE and process pesudo headers only when NET_IP_ALIGN != 0. Verification: Only tested on a platform where NET_IP_ALIGN = 0, with this device: 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet References: [1] https://www.asix.com.tw/en/support/download/file/120 (AX88179 USB3.0 to 10/100/1000M Gigabit Ethernet Controller, version 1.20.0) Signed-off-by: Chun-Chao Yen <nothingstopsme@hotmail.com> --- drivers/net/usb/ax88179_178a.c | 20 +++++++++++++++----- 1 file changed, 15 insertions(+), 5 deletions(-)