diff mbox series

[v6,2/3] spi: dt-bindings: Describe stacked/parallel memories modes

Message ID 20220126112608.955728-3-miquel.raynal@bootlin.com
State Accepted
Commit e2edd1b64f1c79e8abda365149ed62a2a9a494b4
Headers show
Series Stacked/parallel memories bindings | expand

Commit Message

Miquel Raynal Jan. 26, 2022, 11:26 a.m. UTC 
Describe two new memories modes:
- A stacked mode when the bus is common but the address space extended
  with an additinals wires.
- A parallel mode with parallel busses accessing parallel flashes where
  the data is spread.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
---
 .../bindings/spi/spi-peripheral-props.yaml    | 25 +++++++++++++++++++
 1 file changed, 25 insertions(+)

Comments

Rob Herring (Arm) Feb. 4, 2022, 10:20 p.m. UTC | #1 
On Wed, 26 Jan 2022 12:26:06 +0100, Miquel Raynal wrote:
> Describe two new memories modes:
> - A stacked mode when the bus is common but the address space extended
>   with an additinals wires.
> - A parallel mode with parallel busses accessing parallel flashes where
>   the data is spread.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> Acked-by: Pratyush Yadav <p.yadav@ti.com>
> ---
>  .../bindings/spi/spi-peripheral-props.yaml    | 25 +++++++++++++++++++
>  1 file changed, 25 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml b/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
index 5dd209206e88..fedb7ae98ff6 100644
--- a/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
+++ b/Documentation/devicetree/bindings/spi/spi-peripheral-props.yaml
@@ -82,6 +82,31 @@  properties:
     description:
       Delay, in microseconds, after a write transfer.
 
+  stacked-memories:
+    description: Several SPI memories can be wired in stacked mode.
+      This basically means that either a device features several chip
+      selects, or that different devices must be seen as a single
+      bigger chip. This basically doubles (or more) the total address
+      space with only a single additional wire, while still needing
+      to repeat the commands when crossing a chip boundary. The size of
+      each chip should be provided as members of the array.
+    $ref: /schemas/types.yaml#/definitions/uint64-array
+    minItems: 2
+    maxItems: 4
+
+  parallel-memories:
+    description: Several SPI memories can be wired in parallel mode.
+      The devices are physically on a different buses but will always
+      act synchronously as each data word is spread across the
+      different memories (eg. even bits are stored in one memory, odd
+      bits in the other). This basically doubles the address space and
+      the throughput while greatly complexifying the wiring because as
+      many busses as devices must be wired. The size of each chip should
+      be provided as members of the array.
+    $ref: /schemas/types.yaml#/definitions/uint64-array
+    minItems: 2
+    maxItems: 4
+
 # The controller specific properties go here.
 allOf:
   - $ref: cdns,qspi-nor-peripheral-props.yaml#