mbox series

[v2,0/2] add support for Cadence's XSPI controller

Message ID 1626855118-25327-1-git-send-email-pthombar@cadence.com
Headers show
Series add support for Cadence's XSPI controller | expand

Message

Parshuram Raju Thombare July 21, 2021, 8:11 a.m. UTC
This patch series adds support for Cadence's XSPI controller.
This controller supports multiple work modes e.g.
STIG (Software Triggered Instruction Generator) mode, ACMD PIO
and CDMA modes, direct mode.
In STIG mode, controller sends low-level instructions to memory.
Each instruction is 128-bit width. There is special instruction
DataSequence which carries information about data phase.
Driver uses Slave DMA interface to transfer data as only this
interface can be used in STIG work mode.
The CDMA work mode is dedicated for high-performance application
where very low software overhead is required. In this mode the
Command Engine is programmed by the series of linked descriptors
stored in system memory. These descriptors provide commands to execute
and store status information for finished commands.
The PIO mode work mode is dedicated for single operation where
constructing a linked list of descriptors would require too
much effort.
Currently ACMD PIO mode is used for NOR flash read, program, erase
operations, all other operations are handled in STIG work mode.

Changes since v1:
1. Use ACMD PIO work mode for NOR read, program and erase operations,
   for everything else use STIG(Software Triggered Instruction
   Generator) work mode.
2. Changes suggested by Lukas.

Parshuram Thombare (2):
  spi: cadence: add dt-bindings documentation for Cadence XSPI
    controller
  spi: cadence: add support for Cadence XSPI controller

 .../devicetree/bindings/spi/cdns,xspi.yaml         |  169 +++
 drivers/spi/Kconfig                                |   11 +
 drivers/spi/Makefile                               |    1 +
 drivers/spi/spi-cadence-xspi.c                     | 1102 ++++++++++++++++++++
 4 files changed, 1283 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/cdns,xspi.yaml
 create mode 100644 drivers/spi/spi-cadence-xspi.c

Comments

Mark Brown Aug. 2, 2021, 5:32 p.m. UTC | #1
On Wed, Jul 21, 2021 at 10:11:58AM +0200, Parshuram Thombare wrote:
> This patch series adds support for Cadence's XSPI controller.

> This controller supports multiple work modes e.g.

> STIG (Software Triggered Instruction Generator) mode, ACMD PIO

> and CDMA modes, direct mode.


As documented in submitting-patches.rst please send patches to the 
maintainers for the code you would like to change.  The normal kernel
workflow is that people apply patches from their inboxes, if they aren't
copied they are likely to not see the patch at all and it is much more
difficult to apply patches.
Parshuram Raju Thombare Aug. 3, 2021, 5:01 a.m. UTC | #2
Hi Mark,

>As documented in submitting-patches.rst please send patches to the

>maintainers for the code you would like to change.  The normal kernel

>workflow is that people apply patches from their inboxes, if they aren't

>copied they are likely to not see the patch at all and it is much more

>difficult to apply patches.


Sorry, I missed you in last patch set. Pratyush has pointed out some
changes that will be done in v3. I will ensure to add you and other
reviewers/maintainers I missed in v2 patch set.

Regards,
Parshuram Thombare