Index: linux-macro/Documentation/tty/device_drivers/oxsemi-tornado.rst
===================================================================
--- /dev/null
+++ linux-macro/Documentation/tty/device_drivers/oxsemi-tornado.rst
@@ -0,0 +1,129 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====================================================================
+Notes on Oxford Semiconductor PCIe (Tornado) 950 serial port devices
+====================================================================
+
+Oxford Semiconductor PCIe (Tornado) 950 serial port devices are driven
+by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
+
+The baud rate produced by the baud generator is obtained from this input
+frequency by dividing it by the clock prescaler, which can be set to any
+value from 1 to 63.875 in increments of 0.125, and then the usual 16-bit
+divisor is used as with the original 8250, to divide the frequency by a
+value from 1 to 65535.  Finally a programmable oversampling rate is used
+that can take any value from 4 to 16 to divide the frequency further and
+determine the actual baud rate used.  Baud rates from 15625000bps down
+to 0.933bps can be obtained this way.
+
+By default the oversampling rate is set to 16 and the clock prescaler is
+set to 33.875, meaning that the frequency to be used as the reference
+for the usual 16-bit divisor is 115313.653, which is close enough to the
+frequency of 115200 used by the original 8250 for the same values to be
+used for the divisor to obtain the requested baud rates by software that
+is unaware of the extra clock controls available.
+
+The oversampling rate is programmed with the TCR register and the clock
+prescaler is programmed with the CPR/CPR2 register pair[1][2][3][4].
+To switch away from the default value of 33.875 for the prescaler the
+the enhanced mode has to be explicitly enabled though, by setting bit 4
+of the EFR.  In that mode setting bit 7 in the MCR enables the prescaler
+or otherwise it is bypassed as if the value of 1 was used.  Additionally
+writing any value to CPR clears CPR2 for compatibility with old software
+written for older conventional PCI Oxford Semiconductor devices that do
+not have the extra prescaler's 9th bit in CPR2, so the CPR/CPR2 register
+pair has to be programmed in the right order.
+
+By using these parameters rates from 15625000bps down to 1bps can be
+obtained, with either exact or highly-accurate actual bit rates for
+standard and many non-standard rates.
+
+Here are the figures for the standard and some non-standard baud rates
+(including those quoted in Oxford Semiconductor documentation), giving
+the requested rate (r), the actual rate yielded (a) and its deviation
+from the requested rate (d), and the values of the oversampling rate
+(tcr), the clock prescaler (cpr) and the divisor (div) produced by the
+new `get_divisor' handler:
+
+r: 15625000, a: 15625000.00, d:  0.0000%, tcr:  4, cpr:  1.000, div:     1
+r: 12500000, a: 12500000.00, d:  0.0000%, tcr:  5, cpr:  1.000, div:     1
+r: 10416666, a: 10416666.67, d:  0.0000%, tcr:  6, cpr:  1.000, div:     1
+r:  8928571, a:  8928571.43, d:  0.0000%, tcr:  7, cpr:  1.000, div:     1
+r:  7812500, a:  7812500.00, d:  0.0000%, tcr:  8, cpr:  1.000, div:     1
+r:  4000000, a:  4000000.00, d:  0.0000%, tcr:  5, cpr:  3.125, div:     1
+r:  3686400, a:  3676470.59, d: -0.2694%, tcr:  8, cpr:  2.125, div:     1
+r:  3500000, a:  3496503.50, d: -0.0999%, tcr: 13, cpr:  1.375, div:     1
+r:  3000000, a:  2976190.48, d: -0.7937%, tcr: 14, cpr:  1.500, div:     1
+r:  2500000, a:  2500000.00, d:  0.0000%, tcr: 10, cpr:  2.500, div:     1
+r:  2000000, a:  2000000.00, d:  0.0000%, tcr: 10, cpr:  3.125, div:     1
+r:  1843200, a:  1838235.29, d: -0.2694%, tcr: 16, cpr:  2.125, div:     1
+r:  1500000, a:  1492537.31, d: -0.4975%, tcr:  5, cpr:  8.375, div:     1
+r:  1152000, a:  1152073.73, d:  0.0064%, tcr: 14, cpr:  3.875, div:     1
+r:   921600, a:   919117.65, d: -0.2694%, tcr: 16, cpr:  2.125, div:     2
+r:   576000, a:   576036.87, d:  0.0064%, tcr: 14, cpr:  3.875, div:     2
+r:   460800, a:   460829.49, d:  0.0064%, tcr:  7, cpr:  3.875, div:     5
+r:   230400, a:   230414.75, d:  0.0064%, tcr: 14, cpr:  3.875, div:     5
+r:   115200, a:   115207.37, d:  0.0064%, tcr: 14, cpr:  1.250, div:    31
+r:    57600, a:    57603.69, d:  0.0064%, tcr:  8, cpr:  3.875, div:    35
+r:    38400, a:    38402.46, d:  0.0064%, tcr: 14, cpr:  3.875, div:    30
+r:    19200, a:    19201.23, d:  0.0064%, tcr:  8, cpr:  3.875, div:   105
+r:     9600, a:     9600.06, d:  0.0006%, tcr:  9, cpr:  1.125, div:   643
+r:     4800, a:     4799.98, d: -0.0004%, tcr:  7, cpr:  2.875, div:   647
+r:     2400, a:     2400.02, d:  0.0008%, tcr:  9, cpr:  2.250, div:  1286
+r:     1200, a:     1200.00, d:  0.0000%, tcr: 14, cpr:  2.875, div:  1294
+r:      300, a:      300.00, d:  0.0000%, tcr: 11, cpr:  2.625, div:  7215
+r:      200, a:      200.00, d:  0.0000%, tcr: 16, cpr:  1.250, div: 15625
+r:      150, a:      150.00, d:  0.0000%, tcr: 13, cpr:  2.250, div: 14245
+r:      134, a:      134.00, d:  0.0000%, tcr: 11, cpr:  2.625, div: 16153
+r:      110, a:      110.00, d:  0.0000%, tcr: 12, cpr:  1.000, div: 47348
+r:       75, a:       75.00, d:  0.0000%, tcr:  4, cpr:  5.875, div: 35461
+r:       50, a:       50.00, d:  0.0000%, tcr: 16, cpr:  1.250, div: 62500
+r:       25, a:       25.00, d:  0.0000%, tcr: 16, cpr:  2.500, div: 62500
+r:        4, a:        4.00, d:  0.0000%, tcr: 16, cpr: 20.000, div: 48828
+r:        2, a:        2.00, d:  0.0000%, tcr: 16, cpr: 40.000, div: 48828
+r:        1, a:        1.00, d:  0.0000%, tcr: 16, cpr: 63.875, div: 61154
+
+With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX
+limitation imposed by `serial8250_get_baud_rate' standard baud rates
+below 300bps become unavailable in the regular way, e.g. the rate of
+200bps requires the baud base to be divided by 78125 and that is beyond
+the unsigned 16-bit range.  The historic spd_cust feature can still be
+used by encoding the values for, the prescaler, the oversampling rate
+and the clock divisor (DLM/DLL) as follows to obtain such rates if so
+required:
+
+ 31 29 28             20 19   16 15                            0
++-----+-----------------+-------+-------------------------------+
+|0 0 0|    CPR2:CPR     |  TCR  |            DLM:DLL            |
++-----+-----------------+-------+-------------------------------+
+
+Use a value such encoded for the `custom_divisor' field along with the
+ASYNC_SPD_CUST flag set in the `flags' field in `struct serial_struct'
+passed with the TIOCSSERIAL ioctl(2), such as with the setserial(8)
+utility and its `divisor' and `spd_cust' parameters, and the select
+the baud rate of 38400bps.  Note that the value of 0 in TCR sets the
+oversampling rate to 16 and prescaler values below 1 in CPR2/CPR are
+clamped by the driver to 1.
+
+For example the value of 0x1f4004e2 will set CPR2/CPR, TCR and DLM/DLL
+respectively to 0x1f4, 0x0 and 0x04e2, choosing the prescaler value,
+the oversampling rate and the clock divisor of 62.500, 16 and 1250
+respectively.  These parameters will set the baud rate for the serial
+port to 62500000 / 62.500 / 1250 / 16 = 50bps.
+
+References:
+
+[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor,
+    Inc., DS-0045, 10 Nov 2008, Section "950 Mode", pp. 64-65
+
+[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port",
+    Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "950 Mode",
+    p. 20
+
+[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford
+    Semiconductor, Inc., DS-0047, Feb 08, Section "950 Mode", p. 20
+
+[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford
+    Semiconductor, Inc., DS-0048, Feb 08, Section "950 Mode", p. 20
+
+Maciej W. Rozycki  <macro@orcam.me.uk>
Index: linux-macro/drivers/tty/serial/8250/8250.h
===================================================================
--- linux-macro.orig/drivers/tty/serial/8250/8250.h
+++ linux-macro/drivers/tty/serial/8250/8250.h
@@ -120,6 +120,29 @@ static inline void serial_out(struct uar
 	up->port.serial_out(&up->port, offset, value);
 }
 
+/*
+ * For the 16C950
+ */
+static inline void serial_icr_write(struct uart_8250_port *up,
+				    int offset, int value)
+{
+	serial_out(up, UART_SCR, offset);
+	serial_out(up, UART_ICR, value);
+}
+
+static inline unsigned int serial_icr_read(struct uart_8250_port *up,
+					   int offset)
+{
+	unsigned int value;
+
+	serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
+	serial_out(up, UART_SCR, offset);
+	value = serial_in(up, UART_ICR);
+	serial_icr_write(up, UART_ACR, up->acr);
+
+	return value;
+}
+
 void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p);
 
 static inline int serial_dl_read(struct uart_8250_port *up)
Index: linux-macro/drivers/tty/serial/8250/8250_pci.c
===================================================================
--- linux-macro.orig/drivers/tty/serial/8250/8250_pci.c
+++ linux-macro/drivers/tty/serial/8250/8250_pci.c
@@ -1041,6 +1041,208 @@ static int pci_oxsemi_tornado_init(struc
 	return number_uarts;
 }
 
+/* Tornado-specific constants for the TCR and CPR registers; see below.  */
+#define OXSEMI_TORNADO_TCR_MASK	0xf
+#define OXSEMI_TORNADO_CPR_MASK	0x1ff
+#define OXSEMI_TORNADO_CPR_MIN	0x008
+#define OXSEMI_TORNADO_CPR_DEF	0x10f
+
+/*
+ * Determine the oversampling rate, the clock prescaler, and the clock
+ * divisor for the requested baud rate.  The clock rate is 62.5 MHz,
+ * which is four times the baud base, and the prescaler increments in
+ * steps of 1/8.  Therefore to make calculations on integers we need
+ * to use a scaled clock rate, which is the baud base multiplied by 32
+ * (or our assumed UART clock rate multiplied by 2).
+ *
+ * The allowed oversampling rates are from 4 up to 16 inclusive (values
+ * from 0 to 3 inclusive map to 16).  Likewise the clock prescaler allows
+ * values between 1.000 and 63.875 inclusive (operation for values from
+ * 0.000 to 0.875 has not been specified).  The clock divisor is the usual
+ * unsigned 16-bit integer.
+ *
+ * For the most accurate baud rate we use a table of predetermined
+ * oversampling rates and clock prescalers that records all possible
+ * products of the two parameters in the range from 4 up to 255 inclusive,
+ * and additionally 335 for the 1500000bps rate, with the prescaler scaled
+ * by 8.  The table is sorted by the decreasing value of the oversampling
+ * rate and ties are resolved by sorting by the decreasing value of the
+ * product.  This way preference is given to higher oversampling rates.
+ *
+ * We iterate over the table and choose the product of an oversampling
+ * rate and a clock prescaler that gives the lowest integer division
+ * result deviation, or if an exact integer divider is found we stop
+ * looking for it right away.  We do some fixup if the resulting clock
+ * divisor required would be out of its unsigned 16-bit integer range.
+ *
+ * Finally we abuse the supposed fractional part returned to encode the
+ * 4-bit value of the oversampling rate and the 9-bit value of the clock
+ * prescaler which will end up in the TCR and CPR/CPR2 registers.
+ */
+static unsigned int pci_oxsemi_tornado_get_divisor(struct uart_port *port,
+						   unsigned int baud,
+						   unsigned int *frac)
+{
+	static u8 p[][2] = {
+		{ 16, 14, }, { 16, 13, }, { 16, 12, }, { 16, 11, },
+		{ 16, 10, }, { 16,  9, }, { 16,  8, }, { 15, 17, },
+		{ 15, 16, }, { 15, 15, }, { 15, 14, }, { 15, 13, },
+		{ 15, 12, }, { 15, 11, }, { 15, 10, }, { 15,  9, },
+		{ 15,  8, }, { 14, 18, }, { 14, 17, }, { 14, 14, },
+		{ 14, 13, }, { 14, 12, }, { 14, 11, }, { 14, 10, },
+		{ 14,  9, }, { 14,  8, }, { 13, 19, }, { 13, 18, },
+		{ 13, 17, }, { 13, 13, }, { 13, 12, }, { 13, 11, },
+		{ 13, 10, }, { 13,  9, }, { 13,  8, }, { 12, 19, },
+		{ 12, 18, }, { 12, 17, }, { 12, 11, }, { 12,  9, },
+		{ 12,  8, }, { 11, 23, }, { 11, 22, }, { 11, 21, },
+		{ 11, 20, }, { 11, 19, }, { 11, 18, }, { 11, 17, },
+		{ 11, 11, }, { 11, 10, }, { 11,  9, }, { 11,  8, },
+		{ 10, 25, }, { 10, 23, }, { 10, 20, }, { 10, 19, },
+		{ 10, 17, }, { 10, 10, }, { 10,  9, }, { 10,  8, },
+		{  9, 27, }, {  9, 23, }, {  9, 21, }, {  9, 19, },
+		{  9, 18, }, {  9, 17, }, {  9,  9, }, {  9,  8, },
+		{  8, 31, }, {  8, 29, }, {  8, 23, }, {  8, 19, },
+		{  8, 17, }, {  8,  8, }, {  7, 35, }, {  7, 31, },
+		{  7, 29, }, {  7, 25, }, {  7, 23, }, {  7, 21, },
+		{  7, 19, }, {  7, 17, }, {  7, 15, }, {  7, 14, },
+		{  7, 13, }, {  7, 12, }, {  7, 11, }, {  7, 10, },
+		{  7,  9, }, {  7,  8, }, {  6, 41, }, {  6, 37, },
+		{  6, 31, }, {  6, 29, }, {  6, 23, }, {  6, 19, },
+		{  6, 17, }, {  6, 13, }, {  6, 11, }, {  6, 10, },
+		{  6,  9, }, {  6,  8, }, {  5, 67, }, {  5, 47, },
+		{  5, 43, }, {  5, 41, }, {  5, 37, }, {  5, 31, },
+		{  5, 29, }, {  5, 25, }, {  5, 23, }, {  5, 19, },
+		{  5, 17, }, {  5, 15, }, {  5, 13, }, {  5, 11, },
+		{  5, 10, }, {  5,  9, }, {  5,  8, }, {  4, 61, },
+		{  4, 59, }, {  4, 53, }, {  4, 47, }, {  4, 43, },
+		{  4, 41, }, {  4, 37, }, {  4, 31, }, {  4, 29, },
+		{  4, 23, }, {  4, 19, }, {  4, 17, }, {  4, 13, },
+		{  4,  9, }, {  4,  8, },
+	};
+	/* Scale the quotient for comparison to get the fractional part.  */
+	const unsigned int quot_scale = 65536;
+	unsigned int sclk = port->uartclk * 2;
+	unsigned int sdiv = (sclk + (baud / 2)) / baud;
+	unsigned int best_squot;
+	unsigned int squot;
+	unsigned int quot;
+	u16 cpr;
+	u8 tcr;
+	int i;
+
+	/* Old custom speed handling.  */
+	if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) {
+		unsigned int cust_div = port->custom_divisor;
+
+		quot = cust_div & UART_DIV_MAX;
+		tcr = (cust_div >> 16) & OXSEMI_TORNADO_TCR_MASK;
+		cpr = (cust_div >> 20) & OXSEMI_TORNADO_CPR_MASK;
+		if (cpr < OXSEMI_TORNADO_CPR_MIN)
+			cpr = OXSEMI_TORNADO_CPR_DEF;
+	} else {
+		best_squot = quot_scale;
+		for (i = 0; i < ARRAY_SIZE(p); i++) {
+			unsigned int spre;
+			unsigned int srem;
+			u8 cp;
+			u8 tc;
+
+			tc = p[i][0];
+			cp = p[i][1];
+			spre = tc * cp;
+
+			srem = sdiv % spre;
+			if (srem > spre / 2)
+				srem = spre - srem;
+			squot = (srem * quot_scale + spre / 2) / spre;
+
+			if (srem == 0) {
+				tcr = tc;
+				cpr = cp;
+				quot = sdiv / spre;
+				break;
+			} else if (squot < best_squot) {
+				best_squot = squot;
+				tcr = tc;
+				cpr = cp;
+				quot = (sdiv + spre / 2) / spre;
+			}
+		}
+		while (tcr <= (OXSEMI_TORNADO_TCR_MASK + 1) >> 1 &&
+		       quot % 2 == 0) {
+			quot >>= 1;
+			tcr <<= 1;
+		}
+		while (quot > UART_DIV_MAX) {
+			if (tcr <= (OXSEMI_TORNADO_TCR_MASK + 1) >> 1) {
+				quot >>= 1;
+				tcr <<= 1;
+			} else if (cpr <= OXSEMI_TORNADO_CPR_MASK >> 1) {
+				quot >>= 1;
+				cpr <<= 1;
+			} else {
+				quot = quot * cpr / OXSEMI_TORNADO_CPR_MASK;
+				cpr = OXSEMI_TORNADO_CPR_MASK;
+			}
+		}
+	}
+
+	*frac = (cpr << 8) | (tcr & OXSEMI_TORNADO_TCR_MASK);
+	return quot;
+}
+
+/*
+ * Set the oversampling rate in the transmitter clock cycle register (TCR),
+ * the clock prescaler in the clock prescaler register (CPR and CPR2), and
+ * the clock divisor in the divisor latch (DLL and DLM).  Note that for
+ * backwards compatibility any write to CPR clears CPR2 and therefore CPR
+ * has to be written first, followed by CPR2, which occupies the location
+ * of CKS used with earlier UART designs.
+ */
+static void pci_oxsemi_tornado_set_divisor(struct uart_port *port,
+					   unsigned int baud,
+					   unsigned int quot,
+					   unsigned int quot_frac)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+	u8 cpr2 = quot_frac >> 16;
+	u8 cpr = quot_frac >> 8;
+	u8 tcr = quot_frac;
+
+	serial_icr_write(up, UART_TCR, tcr);
+	serial_icr_write(up, UART_CPR, cpr);
+	serial_icr_write(up, UART_CKS, cpr2);
+	serial8250_do_set_divisor(port, baud, quot, 0);
+}
+
+/*
+ * For Tornado devices we force MCR[7] set for the Divide-by-M N/8 baud rate
+ * generator prescaler (CPR and CPR2).  Otherwise no prescaler would be used.
+ */
+static void pci_oxsemi_tornado_set_mctrl(struct uart_port *port,
+					 unsigned int mctrl)
+{
+	struct uart_8250_port *up = up_to_u8250p(port);
+
+	up->mcr |= UART_MCR_CLKSEL;
+	serial8250_do_set_mctrl(port, mctrl);
+}
+
+static int pci_oxsemi_tornado_setup(struct serial_private *priv,
+				    const struct pciserial_board *board,
+				    struct uart_8250_port *up, int idx)
+{
+	struct pci_dev *dev = priv->dev;
+
+	if (pci_oxsemi_tornado_p(dev)) {
+		up->port.get_divisor = pci_oxsemi_tornado_get_divisor;
+		up->port.set_divisor = pci_oxsemi_tornado_set_divisor;
+		up->port.set_mctrl = pci_oxsemi_tornado_set_mctrl;
+	}
+
+	return pci_default_setup(priv, board, up, idx);
+}
+
 static int pci_asix_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
 		  struct uart_8250_port *port, int idx)
@@ -2242,7 +2444,7 @@ static struct pci_serial_quirk pci_seria
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
 		.init		= pci_oxsemi_tornado_init,
-		.setup		= pci_default_setup,
+		.setup		= pci_oxsemi_tornado_setup,
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_MAINPINE,
@@ -2250,7 +2452,7 @@ static struct pci_serial_quirk pci_seria
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
 		.init		= pci_oxsemi_tornado_init,
-		.setup		= pci_default_setup,
+		.setup		= pci_oxsemi_tornado_setup,
 	},
 	{
 		.vendor		= PCI_VENDOR_ID_DIGI,
@@ -2258,7 +2460,7 @@ static struct pci_serial_quirk pci_seria
 		.subvendor		= PCI_SUBVENDOR_ID_IBM,
 		.subdevice		= PCI_ANY_ID,
 		.init			= pci_oxsemi_tornado_init,
-		.setup		= pci_default_setup,
+		.setup		= pci_oxsemi_tornado_setup,
 	},
 	{
 		.vendor         = PCI_VENDOR_ID_INTEL,
@@ -2575,7 +2777,7 @@ enum pci_board_num_t {
 	pbn_b0_2_1843200,
 	pbn_b0_4_1843200,
 
-	pbn_b0_1_3906250,
+	pbn_b0_1_15625000,
 
 	pbn_b0_bt_1_115200,
 	pbn_b0_bt_2_115200,
@@ -2654,10 +2856,10 @@ enum pci_board_num_t {
 	pbn_panacom4,
 	pbn_plx_romulus,
 	pbn_oxsemi,
-	pbn_oxsemi_1_3906250,
-	pbn_oxsemi_2_3906250,
-	pbn_oxsemi_4_3906250,
-	pbn_oxsemi_8_3906250,
+	pbn_oxsemi_1_15625000,
+	pbn_oxsemi_2_15625000,
+	pbn_oxsemi_4_15625000,
+	pbn_oxsemi_8_15625000,
 	pbn_intel_i960,
 	pbn_sgi_ioc3,
 	pbn_computone_4,
@@ -2800,10 +3002,10 @@ static struct pciserial_board pci_boards
 		.uart_offset	= 8,
 	},
 
-	[pbn_b0_1_3906250] = {
+	[pbn_b0_1_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 1,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 8,
 	},
 
@@ -3184,31 +3386,31 @@ static struct pciserial_board pci_boards
 		.base_baud	= 115200,
 		.uart_offset	= 8,
 	},
-	[pbn_oxsemi_1_3906250] = {
+	[pbn_oxsemi_1_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 1,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 0x200,
 		.first_offset	= 0x1000,
 	},
-	[pbn_oxsemi_2_3906250] = {
+	[pbn_oxsemi_2_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 2,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 0x200,
 		.first_offset	= 0x1000,
 	},
-	[pbn_oxsemi_4_3906250] = {
+	[pbn_oxsemi_4_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 4,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 0x200,
 		.first_offset	= 0x1000,
 	},
-	[pbn_oxsemi_8_3906250] = {
+	[pbn_oxsemi_8_15625000] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 8,
-		.base_baud	= 3906250,
+		.base_baud	= 15625000,
 		.uart_offset	= 0x200,
 		.first_offset	= 0x1000,
 	},
@@ -4202,165 +4404,165 @@ static const struct pci_device_id serial
 	 */
 	{	PCI_VENDOR_ID_OXSEMI, 0xc101,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc105,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc11b,    /* OXPCIe952 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc11f,    /* OXPCIe952 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc120,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc124,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc138,    /* OXPCIe952 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc13d,    /* OXPCIe952 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc140,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc141,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc144,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc145,    /* OXPCIe952 1 Legacy UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_b0_1_3906250 },
+		pbn_b0_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc158,    /* OXPCIe952 2 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_2_3906250 },
+		pbn_oxsemi_2_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc15d,    /* OXPCIe952 2 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_2_3906250 },
+		pbn_oxsemi_2_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc208,    /* OXPCIe954 4 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_4_3906250 },
+		pbn_oxsemi_4_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc20d,    /* OXPCIe954 4 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_4_3906250 },
+		pbn_oxsemi_4_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc308,    /* OXPCIe958 8 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_8_3906250 },
+		pbn_oxsemi_8_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc30d,    /* OXPCIe958 8 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_8_3906250 },
+		pbn_oxsemi_8_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc40b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc40f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc41b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc41f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc42b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc42f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc43b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc43f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc44b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc44f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc45b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc45f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc46b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc46f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc47b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc47f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc48b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc48f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc49b,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc49f,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4ab,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4af,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4bb,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4bf,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4cb,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_OXSEMI, 0xc4cf,    /* OXPCIe200 1 Native UART */
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	/*
 	 * Mainpine Inc. IQ Express "Rev3" utilizing OxSemi Tornado
 	 */
 	{	PCI_VENDOR_ID_MAINPINE, 0x4000,	/* IQ Express 1 Port V.34 Super-G3 Fax */
 		PCI_VENDOR_ID_MAINPINE, 0x4001, 0, 0,
-		pbn_oxsemi_1_3906250 },
+		pbn_oxsemi_1_15625000 },
 	{	PCI_VENDOR_ID_MAINPINE, 0x4000,	/* IQ Express 2 Port V.34 Super-G3 Fax */
 		PCI_VENDOR_ID_MAINPINE, 0x4002, 0, 0,
-		pbn_oxsemi_2_3906250 },
+		pbn_oxsemi_2_15625000 },
 	{	PCI_VENDOR_ID_MAINPINE, 0x4000,	/* IQ Express 4 Port V.34 Super-G3 Fax */
 		PCI_VENDOR_ID_MAINPINE, 0x4004, 0, 0,
-		pbn_oxsemi_4_3906250 },
+		pbn_oxsemi_4_15625000 },
 	{	PCI_VENDOR_ID_MAINPINE, 0x4000,	/* IQ Express 8 Port V.34 Super-G3 Fax */
 		PCI_VENDOR_ID_MAINPINE, 0x4008, 0, 0,
-		pbn_oxsemi_8_3906250 },
+		pbn_oxsemi_8_15625000 },
 
 	/*
 	 * Digi/IBM PCIe 2-port Async EIA-232 Adapter utilizing OxSemi Tornado
 	 */
 	{	PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_2_OX_IBM,
 		PCI_SUBVENDOR_ID_IBM, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_2_3906250 },
+		pbn_oxsemi_2_15625000 },
 	/*
 	 * EndRun Technologies. PCI express device range.
 	 * EndRun PTP/1588 has 2 Native UARTs utilizing OxSemi 952.
 	 */
 	{	PCI_VENDOR_ID_ENDRUN, PCI_DEVICE_ID_ENDRUN_1588,
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
-		pbn_oxsemi_2_3906250 },
+		pbn_oxsemi_2_15625000 },
 
 	/*
 	 * SBS Technologies, Inc. P-Octal and PMC-OCTPRO cards,
Index: linux-macro/drivers/tty/serial/8250/8250_port.c
===================================================================
--- linux-macro.orig/drivers/tty/serial/8250/8250_port.c
+++ linux-macro/drivers/tty/serial/8250/8250_port.c
@@ -530,27 +530,6 @@ serial_port_out_sync(struct uart_port *p
 }
 
 /*
- * For the 16C950
- */
-static void serial_icr_write(struct uart_8250_port *up, int offset, int value)
-{
-	serial_out(up, UART_SCR, offset);
-	serial_out(up, UART_ICR, value);
-}
-
-static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
-{
-	unsigned int value;
-
-	serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
-	serial_out(up, UART_SCR, offset);
-	value = serial_in(up, UART_ICR);
-	serial_icr_write(up, UART_ACR, up->acr);
-
-	return value;
-}
-
-/*
  * FIFO support.
  */
 static void serial8250_clear_fifos(struct uart_8250_port *p)
@@ -3322,7 +3301,7 @@ static void serial8250_console_restore(s
 
 	serial8250_set_divisor(port, baud, quot, frac);
 	serial_port_out(port, UART_LCR, up->lcr);
-	serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
+	serial8250_out_MCR(up, up->mcr | UART_MCR_DTR | UART_MCR_RTS);
 }
 
 /*
