@@ -32,22 +32,6 @@ register blocks.
:c:type:`struct ata_port_operations <ata_port_operations>`
----------------------------------------------------------
-Disable ATA port
-~~~~~~~~~~~~~~~~
-
-::
-
- void (*port_disable) (struct ata_port *);
-
-
-Called from :c:func:`ata_bus_probe` error path, as well as when unregistering
-from the SCSI module (rmmod, hot unplug). This function should do
-whatever needs to be done to take the port out of use. In most cases,
-:c:func:`ata_port_disable` can be used as this hook.
-
-Called from :c:func:`ata_bus_probe` on a failed probe. Called from
-:c:func:`ata_scsi_release`.
-
Post-IDENTIFY device configuration
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
@@ -3057,144 +3057,6 @@ int ata_cable_sata(struct ata_port *ap)
}
EXPORT_SYMBOL_GPL(ata_cable_sata);
-/**
- * ata_bus_probe - Reset and probe ATA bus
- * @ap: Bus to probe
- *
- * Master ATA bus probing function. Initiates a hardware-dependent
- * bus reset, then attempts to identify any devices found on
- * the bus.
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- *
- * RETURNS:
- * Zero on success, negative errno otherwise.
- */
-
-int ata_bus_probe(struct ata_port *ap)
-{
- unsigned int classes[ATA_MAX_DEVICES];
- int tries[ATA_MAX_DEVICES];
- int rc;
- struct ata_device *dev;
-
- ata_for_each_dev(dev, &ap->link, ALL)
- tries[dev->devno] = ATA_PROBE_MAX_TRIES;
-
- retry:
- ata_for_each_dev(dev, &ap->link, ALL) {
- /* If we issue an SRST then an ATA drive (not ATAPI)
- * may change configuration and be in PIO0 timing. If
- * we do a hard reset (or are coming from power on)
- * this is true for ATA or ATAPI. Until we've set a
- * suitable controller mode we should not touch the
- * bus as we may be talking too fast.
- */
- dev->pio_mode = XFER_PIO_0;
- dev->dma_mode = 0xff;
-
- /* If the controller has a pio mode setup function
- * then use it to set the chipset to rights. Don't
- * touch the DMA setup as that will be dealt with when
- * configuring devices.
- */
- if (ap->ops->set_piomode)
- ap->ops->set_piomode(ap, dev);
- }
-
- /* reset and determine device classes */
- ap->ops->phy_reset(ap);
-
- ata_for_each_dev(dev, &ap->link, ALL) {
- if (dev->class != ATA_DEV_UNKNOWN)
- classes[dev->devno] = dev->class;
- else
- classes[dev->devno] = ATA_DEV_NONE;
-
- dev->class = ATA_DEV_UNKNOWN;
- }
-
- /* read IDENTIFY page and configure devices. We have to do the identify
- specific sequence bass-ackwards so that PDIAG- is released by
- the slave device */
-
- ata_for_each_dev(dev, &ap->link, ALL_REVERSE) {
- if (tries[dev->devno])
- dev->class = classes[dev->devno];
-
- if (!ata_dev_enabled(dev))
- continue;
-
- rc = ata_dev_read_id(dev, &dev->class, ATA_READID_POSTRESET,
- dev->id);
- if (rc)
- goto fail;
- }
-
- /* Now ask for the cable type as PDIAG- should have been released */
- if (ap->ops->cable_detect)
- ap->cbl = ap->ops->cable_detect(ap);
-
- /* We may have SATA bridge glue hiding here irrespective of
- * the reported cable types and sensed types. When SATA
- * drives indicate we have a bridge, we don't know which end
- * of the link the bridge is which is a problem.
- */
- ata_for_each_dev(dev, &ap->link, ENABLED)
- if (ata_id_is_sata(dev->id))
- ap->cbl = ATA_CBL_SATA;
-
- /* After the identify sequence we can now set up the devices. We do
- this in the normal order so that the user doesn't get confused */
-
- ata_for_each_dev(dev, &ap->link, ENABLED) {
- ap->link.eh_context.i.flags |= ATA_EHI_PRINTINFO;
- rc = ata_dev_configure(dev);
- ap->link.eh_context.i.flags &= ~ATA_EHI_PRINTINFO;
- if (rc)
- goto fail;
- }
-
- /* configure transfer mode */
- rc = ata_set_mode(&ap->link, &dev);
- if (rc)
- goto fail;
-
- ata_for_each_dev(dev, &ap->link, ENABLED)
- return 0;
-
- return -ENODEV;
-
- fail:
- tries[dev->devno]--;
-
- switch (rc) {
- case -EINVAL:
- /* eeek, something went very wrong, give up */
- tries[dev->devno] = 0;
- break;
-
- case -ENODEV:
- /* give it just one more chance */
- tries[dev->devno] = min(tries[dev->devno], 1);
- fallthrough;
- case -EIO:
- if (tries[dev->devno] == 1) {
- /* This is the last chance, better to slow
- * down than lose it.
- */
- sata_down_spd_limit(&ap->link, 0);
- ata_down_xfermask_limit(dev, ATA_DNXFER_PIO);
- }
- }
-
- if (!tries[dev->devno])
- ata_dev_disable(dev);
-
- goto retry;
-}
-
/**
* sata_print_link_status - Print SATA link status
* @link: SATA link to printk link status about
@@ -122,7 +122,6 @@ extern void ata_scsi_media_change_notify(struct ata_device *dev);
extern void ata_scsi_hotplug(struct work_struct *work);
extern void ata_schedule_scsi_eh(struct Scsi_Host *shost);
extern void ata_scsi_dev_rescan(struct work_struct *work);
-extern int ata_bus_probe(struct ata_port *ap);
extern int ata_scsi_user_scan(struct Scsi_Host *shost, unsigned int channel,
unsigned int id, u64 lun);
void ata_scsi_sdev_config(struct scsi_device *sdev);
@@ -344,7 +344,6 @@ enum {
ATA_LINK_RESUME_TRIES = 5,
/* how hard are we gonna try to probe/recover devices */
- ATA_PROBE_MAX_TRIES = 3,
ATA_EH_DEV_TRIES = 3,
ATA_EH_PMP_TRIES = 5,
ATA_EH_PMP_LINK_TRIES = 3,