@@ -10,17 +10,6 @@ config SCSI_ACORNSCSI_3
This enables support for the Acorn SCSI card (aka30). If you have an
Acorn system with one of these, say Y. If unsure, say N.
-config SCSI_ACORNSCSI_TAGGED_QUEUE
- bool "Support SCSI 2 Tagged queueing"
- depends on SCSI_ACORNSCSI_3
- help
- Say Y here to enable tagged queuing support on the Acorn SCSI card.
-
- This is a feature of SCSI-2 which improves performance: the host
- adapter can send several SCSI commands to a device's queue even if
- previous commands haven't finished yet. Some SCSI devices don't
- implement this properly, so the safe answer is N.
-
config SCSI_ACORNSCSI_SYNC
bool "Support SCSI 2 Synchronous Transfers"
depends on SCSI_ACORNSCSI_3
@@ -52,12 +52,8 @@
* You can tell if you have a device that supports tagged queueing my
* cating (eg) /proc/scsi/acornscsi/0 and see if the SCSI revision is reported
* as '2 TAG'.
- *
- * Also note that CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE is normally set in the config
- * scripts, but disabled here. Once debugged, remove the #undef, otherwise to debug,
- * comment out the undef.
*/
-#undef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
+
/*
* SCSI-II Synchronous transfer support.
*
@@ -171,7 +167,7 @@ static void acornscsi_done(AS_Host *host, struct scsi_cmnd **SCpntp,
unsigned int result);
static int acornscsi_reconnect_finish(AS_Host *host);
static void acornscsi_dma_cleanup(AS_Host *host);
-static void acornscsi_abortcmd(AS_Host *host, unsigned char tag);
+static void acornscsi_abortcmd(AS_Host *host);
/* ====================================================================================
* Miscellaneous
@@ -741,17 +737,6 @@ intr_ret_t acornscsi_kick(AS_Host *host)
#endif
if (from_queue) {
-#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
- /*
- * tagged queueing - allocate a new tag to this command
- */
- if (SCpnt->device->simple_tags) {
- SCpnt->device->current_tag += 1;
- if (SCpnt->device->current_tag == 0)
- SCpnt->device->current_tag = 1;
- SCpnt->tag = SCpnt->device->current_tag;
- } else
-#endif
set_bit(SCpnt->device->id * 8 +
(u8)(SCpnt->device->lun & 0x07), host->busyluns);
@@ -1192,7 +1177,7 @@ void acornscsi_dma_intr(AS_Host *host)
* the device recognises the attention.
*/
if (dmac_read(host, DMAC_STATUS) & STATUS_RQ0) {
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
dmac_write(host, DMAC_TXCNTLO, 0);
dmac_write(host, DMAC_TXCNTHI, 0);
@@ -1560,23 +1545,6 @@ void acornscsi_message(AS_Host *host)
acornscsi_sbic_issuecmd(host, CMND_ASSERTATN);
switch (host->scsi.last_message) {
-#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
- case HEAD_OF_QUEUE_TAG:
- case ORDERED_QUEUE_TAG:
- case SIMPLE_QUEUE_TAG:
- /*
- * ANSI standard says: (Section SCSI-2 Rev. 10c Sect 5.6.17)
- * If a target does not implement tagged queuing and a queue tag
- * message is received, it shall respond with a MESSAGE REJECT
- * message and accept the I/O process as if it were untagged.
- */
- printk(KERN_NOTICE "scsi%d.%c: disabling tagged queueing\n",
- host->host->host_no, acornscsi_target(host));
- host->SCpnt->device->simple_tags = 0;
- set_bit(host->SCpnt->device->id * 8 +
- (u8)(host->SCpnt->device->lun & 0x7), host->busyluns);
- break;
-#endif
case EXTENDED_MESSAGE | (EXTENDED_SDTR << 8):
/*
* Target can't handle synchronous transfers
@@ -1687,24 +1655,11 @@ void acornscsi_buildmessages(AS_Host *host)
#if 0
/* does the device need the current command aborted */
if (cmd_aborted) {
- acornscsi_abortcmd(host->SCpnt->tag);
+ acornscsi_abortcmd(host);
return;
}
#endif
-#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
- if (host->SCpnt->tag) {
- unsigned int tag_type;
-
- if (host->SCpnt->cmnd[0] == REQUEST_SENSE ||
- host->SCpnt->cmnd[0] == TEST_UNIT_READY ||
- host->SCpnt->cmnd[0] == INQUIRY)
- tag_type = HEAD_OF_QUEUE_TAG;
- else
- tag_type = SIMPLE_QUEUE_TAG;
- msgqueue_addmsg(&host->scsi.msgs, 2, tag_type, host->SCpnt->tag);
- }
-#endif
#ifdef CONFIG_SCSI_ACORNSCSI_SYNC
if (host->device[host->SCpnt->device->id].sync_state == SYNC_NEGOCIATE) {
@@ -1798,7 +1753,7 @@ int acornscsi_reconnect(AS_Host *host)
"to reconnect with\n",
host->host->host_no, '0' + target);
acornscsi_dumplog(host, target);
- acornscsi_abortcmd(host, 0);
+ acornscsi_abortcmd(host);
if (host->SCpnt) {
queue_add_cmd_tail(&host->queues.disconnected, host->SCpnt);
host->SCpnt = NULL;
@@ -1821,7 +1776,7 @@ int acornscsi_reconnect_finish(AS_Host *host)
host->scsi.disconnectable = 0;
if (host->SCpnt->device->id == host->scsi.reconnected.target &&
host->SCpnt->device->lun == host->scsi.reconnected.lun &&
- host->SCpnt->tag == host->scsi.reconnected.tag) {
+ scsi_cmd_to_tag(host->SCpnt) == host->scsi.reconnected.tag) {
#if (DEBUG & (DEBUG_QUEUES|DEBUG_DISCON))
DBG(host->SCpnt, printk("scsi%d.%c: reconnected",
host->host->host_no, acornscsi_target(host)));
@@ -1848,7 +1803,7 @@ int acornscsi_reconnect_finish(AS_Host *host)
}
if (!host->SCpnt)
- acornscsi_abortcmd(host, host->scsi.reconnected.tag);
+ acornscsi_abortcmd(host);
else {
/*
* Restore data pointer from SAVED pointers.
@@ -1889,21 +1844,15 @@ void acornscsi_disconnect_unexpected(AS_Host *host)
* Function: void acornscsi_abortcmd(AS_host *host, unsigned char tag)
* Purpose : abort a currently executing command
* Params : host - host with connected command to abort
- * tag - tag to abort
*/
static
-void acornscsi_abortcmd(AS_Host *host, unsigned char tag)
+void acornscsi_abortcmd(AS_Host *host)
{
host->scsi.phase = PHASE_ABORTED;
sbic_arm_write(host, SBIC_CMND, CMND_ASSERTATN);
msgqueue_flush(&host->scsi.msgs);
-#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
- if (tag)
- msgqueue_addmsg(&host->scsi.msgs, 2, ABORT_TAG, tag);
- else
-#endif
- msgqueue_addmsg(&host->scsi.msgs, 1, ABORT);
+ msgqueue_addmsg(&host->scsi.msgs, 1, ABORT);
}
/* ==========================================================================================
@@ -1993,7 +1942,7 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq)
printk(KERN_ERR "scsi%d.%c: PHASE_CONNECTING, SSR %02X?\n",
host->host->host_no, acornscsi_target(host), ssr);
acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
}
return INTR_PROCESSING;
@@ -2029,7 +1978,7 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq)
printk(KERN_ERR "scsi%d.%c: PHASE_CONNECTED, SSR %02X?\n",
host->host->host_no, acornscsi_target(host), ssr);
acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
}
return INTR_PROCESSING;
@@ -2075,20 +2024,20 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq)
case 0x18: /* -> PHASE_DATAOUT */
/* COMMAND -> DATA OUT */
if (host->scsi.SCp.sent_command != host->SCpnt->cmd_len)
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
acornscsi_dma_setup(host, DMA_OUT);
if (!acornscsi_starttransfer(host))
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
host->scsi.phase = PHASE_DATAOUT;
return INTR_IDLE;
case 0x19: /* -> PHASE_DATAIN */
/* COMMAND -> DATA IN */
if (host->scsi.SCp.sent_command != host->SCpnt->cmd_len)
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
acornscsi_dma_setup(host, DMA_IN);
if (!acornscsi_starttransfer(host))
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
host->scsi.phase = PHASE_DATAIN;
return INTR_IDLE;
@@ -2156,7 +2105,7 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq)
/* MESSAGE IN -> DATA OUT */
acornscsi_dma_setup(host, DMA_OUT);
if (!acornscsi_starttransfer(host))
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
host->scsi.phase = PHASE_DATAOUT;
return INTR_IDLE;
@@ -2165,7 +2114,7 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq)
/* MESSAGE IN -> DATA IN */
acornscsi_dma_setup(host, DMA_IN);
if (!acornscsi_starttransfer(host))
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
host->scsi.phase = PHASE_DATAIN;
return INTR_IDLE;
@@ -2206,7 +2155,7 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq)
switch (ssr) {
case 0x19: /* -> PHASE_DATAIN */
case 0x89: /* -> PHASE_DATAIN */
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
return INTR_IDLE;
case 0x1b: /* -> PHASE_STATUSIN */
@@ -2255,7 +2204,7 @@ intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq)
switch (ssr) {
case 0x18: /* -> PHASE_DATAOUT */
case 0x88: /* -> PHASE_DATAOUT */
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
return INTR_IDLE;
case 0x1b: /* -> PHASE_STATUSIN */
@@ -2482,7 +2431,6 @@ static int acornscsi_queuecmd_lck(struct scsi_cmnd *SCpnt,
SCpnt->scsi_done = done;
SCpnt->host_scribble = NULL;
SCpnt->result = 0;
- SCpnt->tag = 0;
SCpnt->SCp.phase = (int)acornscsi_datadirection(SCpnt->cmnd[0]);
SCpnt->SCp.sent_command = 0;
SCpnt->SCp.scsi_xferred = 0;
@@ -2581,7 +2529,7 @@ static enum res_abort acornscsi_do_abort(AS_Host *host, struct scsi_cmnd *SCpnt)
break;
default:
- acornscsi_abortcmd(host, host->SCpnt->tag);
+ acornscsi_abortcmd(host);
res = res_snooze;
}
local_irq_restore(flags);
@@ -2746,9 +2694,6 @@ char *acornscsi_info(struct Scsi_Host *host)
#ifdef CONFIG_SCSI_ACORNSCSI_SYNC
" SYNC"
#endif
-#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
- " TAG"
-#endif
#if (DEBUG & DEBUG_NO_WRITE)
" NOWRITE (" __stringify(NO_WRITE) ")"
#endif
@@ -2769,9 +2714,6 @@ static int acornscsi_show_info(struct seq_file *m, struct Scsi_Host *instance)
#ifdef CONFIG_SCSI_ACORNSCSI_SYNC
" SYNC"
#endif
-#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
- " TAG"
-#endif
#if (DEBUG & DEBUG_NO_WRITE)
" NOWRITE (" __stringify(NO_WRITE) ")"
#endif
@@ -2826,9 +2768,8 @@ static int acornscsi_show_info(struct seq_file *m, struct Scsi_Host *instance)
seq_printf(m, "Device/Lun TaggedQ Sync\n");
seq_printf(m, " %d/%llu ", scd->id, scd->lun);
if (scd->tagged_supported)
- seq_printf(m, "%3sabled(%3d) ",
- scd->simple_tags ? "en" : "dis",
- scd->current_tag);
+ seq_printf(m, "%3sabled ",
+ scd->simple_tags ? "en" : "dis");
else
seq_printf(m, "unsupported ");
@@ -214,7 +214,7 @@ struct scsi_cmnd *queue_remove_tgtluntag(Queue_t *queue, int target, int lun,
list_for_each(l, &queue->head) {
QE_t *q = list_entry(l, QE_t, list);
if (q->SCpnt->device->id == target && q->SCpnt->device->lun == lun &&
- q->SCpnt->tag == tag) {
+ scsi_cmd_to_tag(q->SCpnt) == tag) {
SCpnt = __queue_remove(queue, l);
break;
}
The acornscsi driver has a config option to enable tagged queuing, but this option gets disabled in the driver itself with the comment 'needs to be debugged'. As this is a _really_ old driver I doubt anyone will be wanting to invest time here, so remove the tagged queue vestiges and make our live easier. Signed-off-by: Hannes Reinecke <hare@suse.de> --- drivers/scsi/arm/Kconfig | 11 ---- drivers/scsi/arm/acornscsi.c | 103 ++++++++--------------------------- drivers/scsi/arm/queue.c | 2 +- 3 files changed, 23 insertions(+), 93 deletions(-)