@@ -234,7 +234,7 @@ struct sym_reg {
#define IRQM 0x08 /* mod: irq mode (1 = totem pole !) */
#define STD 0x04 /* cmd: start dma mode */
#define IRQD 0x02 /* mod: irq disable */
- #define NOCOM 0x01 /* cmd: protect sfbr while reselect */
+ #define NOCOM 0x01 /* cmd: protect sfbr while reselect */
/* bits 0-1 rsvd for C1010 */
/*3c*/ u32 nc_adder;
@@ -332,16 +332,16 @@ static unsigned getfreq (struct sym_hcb *np, int gen)
OUTW(np, nc_sien, 0);
OUTB(np, nc_istat1, 0);
}
- /*
- * set prescaler to divide by whatever 0 means
- * 0 ought to choose divide by 2, but appears
- * to set divide by 3.5 mode in my 53c810 ...
- */
- OUTB(np, nc_scntl3, 0);
-
- /*
- * adjust for prescaler, and convert into KHz
- */
+ /*
+ * set prescaler to divide by whatever 0 means
+ * 0 ought to choose divide by 2, but appears
+ * to set divide by 3.5 mode in my 53c810 ...
+ */
+ OUTB(np, nc_scntl3, 0);
+
+ /*
+ * adjust for prescaler, and convert into KHz
+ */
f = ms ? ((1 << gen) * (4340*4)) / ms : 0;
/*
@@ -688,7 +688,7 @@ static int sym_prepare_setting(struct Scsi_Host *shost, struct sym_hcb *np, stru
/*
* Get the clock multiplier factor.
- */
+ */
if (np->features & FE_QUAD)
np->multiplier = 4;
else if (np->features & FE_DBLR)
@@ -774,11 +774,11 @@ static int sym_prepare_setting(struct Scsi_Host *shost, struct sym_hcb *np, stru
/*
* Phase mismatch handled by SCRIPTS (895A/896/1010) ?
- */
+ */
if (np->features & FE_NOPM)
np->rv_ccntl0 |= (ENPMJ);
- /*
+ /*
* C1010-33 Errata: Part Number:609-039638 (rev. 1) is fixed.
* In dual channel mode, contention occurs if internal cycles
* are used. Disable internal cycles.
@@ -1692,12 +1692,12 @@ void sym_start_up(struct Scsi_Host *shost, int reason)
struct sym_data *sym_data = shost_priv(shost);
struct pci_dev *pdev = sym_data->pdev;
struct sym_hcb *np = sym_data->ncb;
- int i;
+ int i;
u32 phys;
- /*
+ /*
* Reset chip if asked, otherwise just clear fifos.
- */
+ */
if (reason == 1)
sym_soft_reset(np);
else {
@@ -3080,7 +3080,7 @@ static void sym_sir_bad_scsi_status(struct sym_hcb *np, int num, struct sym_ccb
sym_dequeue_from_squeue(np, i, cp->target, cp->lun, -1);
OUTL_DSP(np, SCRIPTA_BA(np, start));
- /*
+ /*
* Save some info of the actual IO.
* Compute the data residual.
*/
@@ -3573,9 +3573,9 @@ static void sym_sir_task_recovery(struct sym_hcb *np, int num)
sym_clear_tasks(np, DID_ABORT, target, lun, task);
sym_flush_comp_queue(np, 0);
- /*
+ /*
* If we sent a BDR, make upper layer aware of that.
- */
+ */
if (np->abrt_msg[0] == M_RESET)
starget_printk(KERN_NOTICE, starget,
"has been reset\n");
@@ -4902,7 +4902,7 @@ static struct sym_ccb *sym_alloc_ccb(struct sym_hcb *np)
cp->phys.head.go.start = cpu_to_scr(SCRIPTA_BA(np, idle));
cp->phys.head.go.restart = cpu_to_scr(SCRIPTB_BA(np, bad_i_t_l));
- /*
+ /*
* Initilialyze some other fields.
*/
cp->phys.smsg_ext.addr = cpu_to_scr(HCB_BA(np, msgin[2]));
There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/' Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Hui Tang <tanghui20@huawei.com> --- drivers/scsi/sym53c8xx_2/sym_defs.h | 2 +- drivers/scsi/sym53c8xx_2/sym_hipd.c | 40 ++++++++++++++++++------------------- 2 files changed, 21 insertions(+), 21 deletions(-)