diff mbox series

[v8,5/7] ARM: dts: exynos: Add interconnect properties to Exynos4412 bus nodes

Message ID 20201104103657.18007-6-s.nawrocki@samsung.com
State New
Headers show
Series [v8,1/7] dt-bindings: devfreq: Add documentation for the interconnect properties | expand

Commit Message

Sylwester Nawrocki/Kernel \(PLT\) /SRPOL/Staff Engineer/Samsung Electronics Nov. 4, 2020, 10:36 a.m. UTC 
This patch adds the following properties for Exynos4412 interconnect
bus nodes:
 - interconnects: to declare connections between nodes in order to
   guarantee PM QoS requirements between nodes,
 - #interconnect-cells: required by the interconnect framework,
 - samsung,data-clk-ratio: which allows to specify minimum data clock
   frequency corresponding to requested bandwidth for each bus.

Note that #interconnect-cells is always zero and node IDs are not
hardcoded anywhere.

Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
---
Changes for v8:
 - none.

Changes for v7:
 - adjusted to the DT property changes: "interconnects" instead
   of "samsung,interconnect-parent", "samsung,data-clk-ratio"
   instead of "bus-width".

Changes for v6:
 - added bus-width property in bus_dmc node.

Changes for v5:
 - adjust to renamed exynos,interconnect-parent-node property,
 - add properties in common exynos4412.dtsi file rather than
   in Odroid specific odroid4412-odroid-common.dtsi.
---
 arch/arm/boot/dts/exynos4412.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

Comments

Krzysztof Kozlowski Nov. 10, 2020, 6:11 p.m. UTC | #1 
On Wed, Nov 04, 2020 at 11:36:55AM +0100, Sylwester Nawrocki wrote:
> This patch adds the following properties for Exynos4412 interconnect
> bus nodes:
>  - interconnects: to declare connections between nodes in order to
>    guarantee PM QoS requirements between nodes,
>  - #interconnect-cells: required by the interconnect framework,
>  - samsung,data-clk-ratio: which allows to specify minimum data clock
>    frequency corresponding to requested bandwidth for each bus.
> 
> Note that #interconnect-cells is always zero and node IDs are not
> hardcoded anywhere.
> 
> Signed-off-by: Artur Świgoń <a.swigon@samsung.com>
> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
> ---
> Changes for v8:
>  - none.
> 
> Changes for v7:
>  - adjusted to the DT property changes: "interconnects" instead
>    of "samsung,interconnect-parent", "samsung,data-clk-ratio"
>    instead of "bus-width".
> 
> Changes for v6:
>  - added bus-width property in bus_dmc node.
> 
> Changes for v5:
>  - adjust to renamed exynos,interconnect-parent-node property,
>  - add properties in common exynos4412.dtsi file rather than
>    in Odroid specific odroid4412-odroid-common.dtsi.
> ---
>  arch/arm/boot/dts/exynos4412.dtsi | 6 ++++++

Thanks, applied with Chanwoo's tags.

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/exynos4412.dtsi b/arch/arm/boot/dts/exynos4412.dtsi
index e76881d..4999e68 100644
--- a/arch/arm/boot/dts/exynos4412.dtsi
+++ b/arch/arm/boot/dts/exynos4412.dtsi
@@ -383,6 +383,8 @@ 
 			clocks = <&clock CLK_DIV_DMC>;
 			clock-names = "bus";
 			operating-points-v2 = <&bus_dmc_opp_table>;
+			samsung,data-clock-ratio = <4>;
+			#interconnect-cells = <0>;
 			status = "disabled";
 		};
 
@@ -452,6 +454,8 @@ 
 			clocks = <&clock CLK_DIV_GDL>;
 			clock-names = "bus";
 			operating-points-v2 = <&bus_leftbus_opp_table>;
+			interconnects = <&bus_dmc>;
+			#interconnect-cells = <0>;
 			status = "disabled";
 		};
 
@@ -468,6 +472,8 @@ 
 			clocks = <&clock CLK_ACLK160>;
 			clock-names = "bus";
 			operating-points-v2 = <&bus_display_opp_table>;
+			interconnects = <&bus_leftbus &bus_dmc>;
+			#interconnect-cells = <0>;
 			status = "disabled";
 		};