diff mbox series

[V2,3/4] thermal: intel: pch: enhance overheat handling

Message ID 20220519143508.3803894-4-rui.zhang@intel.com
State Accepted
Commit 92923028e9795055debc460243cc246cc9284cd1
Headers show
Series PM/Thermal: Enhance PCH overheat handling | expand

Commit Message

Zhang Rui May 19, 2022, 2:35 p.m. UTC
Commit ef63b043ac86 ("thermal: intel: pch: fix S0ix failure due to PCH
temperature above threshold") introduces delay loop mechanism that allows
PCH temperature to go down below threshold during suspend so it won't
block S0ix. And the default overall delay timeout is 1 second.

However, in practice, we found that the time it takes to cool the PCH down
below threshold highly depends on the initial PCH temperature when the
delay starts, as well as the ambient temperature.
And in some cases, the 1 second delay is not sufficient. As a result, the
system stays in a shallower power state like PCx instead of S0ix, and
drains the battery power, without user' notice.

To make sure S0ix is not blocked by the PCH overheating, we
1. expand the default overall timeout to 60 seconds.
2. make sure the temperature is below threshold rather than equal to it.

At the same time, as the cooling delay can be much longer and many wakeup
events (ACPI Power Button press, USB mouse move, etc) becomes valid in the
suspend_noirq phase, add detection of wakeup event so that the driver
does not delay blindly when the system suspend is likely to abort soon.

This patch may introduce longer suspend time, but only in the cases when
the system overheats and Linux used to enter a shallower S2idle state,
say, PCx instead of S0ix.

Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
---
 drivers/thermal/intel/intel_pch_thermal.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)
diff mbox series

Patch

diff --git a/drivers/thermal/intel/intel_pch_thermal.c b/drivers/thermal/intel/intel_pch_thermal.c
index c0f651b5905d..b7b32e2f5ae2 100644
--- a/drivers/thermal/intel/intel_pch_thermal.c
+++ b/drivers/thermal/intel/intel_pch_thermal.c
@@ -70,8 +70,8 @@  static unsigned int delay_timeout = 100;
 module_param(delay_timeout, int, 0644);
 MODULE_PARM_DESC(delay_timeout, "amount of time delay for each iteration.");
 
-/* Number of iterations for cooling delay, 10 counts by default for now */
-static unsigned int delay_cnt = 10;
+/* Number of iterations for cooling delay, 600 counts by default for now */
+static unsigned int delay_cnt = 600;
 module_param(delay_cnt, int, 0644);
 MODULE_PARM_DESC(delay_cnt, "total number of iterations for time delay.");
 
@@ -197,7 +197,7 @@  static int pch_wpt_get_temp(struct pch_thermal_device *ptd, int *temp)
 static int pch_wpt_suspend(struct pch_thermal_device *ptd)
 {
 	u8 tsel;
-	u8 pch_delay_cnt = 1;
+	int pch_delay_cnt = 1;
 	u16 pch_thr_temp, pch_cur_temp;
 
 	/* Shutdown the thermal sensor if it is not enabled by BIOS */
@@ -234,7 +234,10 @@  static int pch_wpt_suspend(struct pch_thermal_device *ptd)
 	 * which helps to indentify the reason why S0ix entry was rejected.
 	 */
 	while (pch_delay_cnt <= delay_cnt) {
-		if (pch_cur_temp <= pch_thr_temp)
+		if (pch_cur_temp < pch_thr_temp)
+			break;
+
+		if (pm_wakeup_pending())
 			break;
 
 		dev_warn(&ptd->pdev->dev,
@@ -246,7 +249,7 @@  static int pch_wpt_suspend(struct pch_thermal_device *ptd)
 		pch_delay_cnt++;
 	}
 
-	if (pch_cur_temp > pch_thr_temp)
+	if (pch_cur_temp >= pch_thr_temp)
 		dev_warn(&ptd->pdev->dev,
 			"CPU-PCH is hot [%dC] even after delay, continue to suspend. S0ix might fail\n",
 			pch_cur_temp);