diff mbox series

[v2,10/10] power: supply: axp288_fuel_gauge: Take the P-Unit semaphore only once during probe()

Message ID 20210730095607.57541-11-hdegoede@redhat.com
State Superseded
Headers show
Series power: supply: axp288_fuel_gauge: Reduce number of register accesses + cleanups | expand

Commit Message

Hans de Goede July 30, 2021, 9:56 a.m. UTC 
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. If not explicitly taken by the I2C-driver,
then this semaphore is automatically taken by the I2C-bus-driver for
each I2C-transfer and this is a quite expensive operation.

Explicitly take the semaphore in probe() around the register-accesses
done during probe, so that this only needs to be done once, rather then
once per register-access.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 drivers/power/supply/axp288_fuel_gauge.c | 24 +++++++++++++++++-------
 1 file changed, 17 insertions(+), 7 deletions(-)
diff mbox series

Patch

diff --git a/drivers/power/supply/axp288_fuel_gauge.c b/drivers/power/supply/axp288_fuel_gauge.c
index 016d8d6bec40..c1da217fdb0e 100644
--- a/drivers/power/supply/axp288_fuel_gauge.c
+++ b/drivers/power/supply/axp288_fuel_gauge.c
@@ -661,31 +661,35 @@  static int axp288_fuel_gauge_probe(struct platform_device *pdev)
 		}
 	}
 
+	ret = iosf_mbi_block_punit_i2c_access();
+	if (ret < 0)
+		goto out_free_iio_chan;
+
 	/*
 	 * On some devices the fuelgauge and charger parts of the axp288 are
 	 * not used, check that the fuelgauge is enabled (CC_CTRL != 0).
 	 */
 	ret = regmap_read(axp20x->regmap, AXP20X_CC_CTRL, &val);
 	if (ret < 0)
-		goto out_free_iio_chan;
+		goto unblock_punit_i2c_access;
 	if (val == 0) {
 		ret = -ENODEV;
-		goto out_free_iio_chan;
+		goto unblock_punit_i2c_access;
 	}
 
 	ret = fuel_gauge_reg_readb(info, AXP288_FG_DES_CAP1_REG);
 	if (ret < 0)
-		goto out_free_iio_chan;
+		goto unblock_punit_i2c_access;
 
 	if (!(ret & FG_DES_CAP1_VALID)) {
 		dev_err(&pdev->dev, "axp288 not configured by firmware\n");
 		ret = -ENODEV;
-		goto out_free_iio_chan;
+		goto unblock_punit_i2c_access;
 	}
 
 	ret = fuel_gauge_reg_readb(info, AXP20X_CHRG_CTRL1);
 	if (ret < 0)
-		goto out_free_iio_chan;
+		goto unblock_punit_i2c_access;
 	switch ((ret & CHRG_CCCV_CV_MASK) >> CHRG_CCCV_CV_BIT_POS) {
 	case CHRG_CCCV_CV_4100MV:
 		info->max_volt = 4100;
@@ -703,14 +707,20 @@  static int axp288_fuel_gauge_probe(struct platform_device *pdev)
 
 	ret = fuel_gauge_reg_readb(info, AXP20X_PWR_OP_MODE);
 	if (ret < 0)
-		goto out_free_iio_chan;
+		goto unblock_punit_i2c_access;
 	info->pwr_op = ret;
 
 	ret = fuel_gauge_reg_readb(info, AXP288_FG_LOW_CAP_REG);
 	if (ret < 0)
-		goto out_free_iio_chan;
+		goto unblock_punit_i2c_access;
 	info->low_cap = ret;
 
+unblock_punit_i2c_access:
+	iosf_mbi_unblock_punit_i2c_access();
+	/* In case we arrive here by goto because of a register access error */
+	if (ret < 0)
+		goto out_free_iio_chan;
+
 	psy_cfg.drv_data = info;
 	info->bat = power_supply_register(&pdev->dev, &fuel_gauge_desc, &psy_cfg);
 	if (IS_ERR(info->bat)) {