@@ -269,43 +269,43 @@ enum bup_vch_sel {
/*
* ADC for the battery thermistor.
- * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined
+ * When using the AB8500_ADC_THERM_BATCTRL the battery ID resistor is combined
* with a NTC resistor to both identify the battery and to measure its
* temperature. Different phone manufactures uses different techniques to both
* identify the battery and to read its temperature.
*/
-enum abx500_adc_therm {
- ABx500_ADC_THERM_BATCTRL,
- ABx500_ADC_THERM_BATTEMP,
+enum ab8500_adc_therm {
+ AB8500_ADC_THERM_BATCTRL,
+ AB8500_ADC_THERM_BATTEMP,
};
/**
- * struct abx500_res_to_temp - defines one point in a temp to res curve. To
+ * struct ab8500_res_to_temp - defines one point in a temp to res curve. To
* be used in battery packs that combines the identification resistor with a
* NTC resistor.
* @temp: battery pack temperature in Celsius
* @resist: NTC resistor net total resistance
*/
-struct abx500_res_to_temp {
+struct ab8500_res_to_temp {
int temp;
int resist;
};
/**
- * struct abx500_v_to_cap - Table for translating voltage to capacity
+ * struct ab8500_v_to_cap - Table for translating voltage to capacity
* @voltage: Voltage in mV
* @capacity: Capacity in percent
*/
-struct abx500_v_to_cap {
+struct ab8500_v_to_cap {
int voltage;
int capacity;
};
/* Forward declaration */
-struct abx500_fg;
+struct ab8500_fg;
/**
- * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds
+ * struct ab8500_fg_parameters - Fuel gauge algorithm parameters, in seconds
* if not specified
* @recovery_sleep_timer: Time between measurements while recovering
* @recovery_total_time: Total recovery time
@@ -333,7 +333,7 @@ struct abx500_fg;
* @pcut_max_restart: Max number of restarts
* @pcut_debounce_time: Sets battery debounce time
*/
-struct abx500_fg_parameters {
+struct ab8500_fg_parameters {
int recovery_sleep_timer;
int recovery_total_time;
int init_timer;
@@ -357,13 +357,13 @@ struct abx500_fg_parameters {
};
/**
- * struct abx500_charger_maximization - struct used by the board config.
+ * struct ab8500_charger_maximization - struct used by the board config.
* @use_maxi: Enable maximization for this battery type
* @maxi_chg_curr: Maximum charger current allowed
* @maxi_wait_cycles: cycles to wait before setting charger current
* @charger_curr_step delta between two charger current settings (mA)
*/
-struct abx500_maxim_parameters {
+struct ab8500_maxim_parameters {
bool ena_maxi;
int chg_curr;
int wait_cycles;
@@ -371,7 +371,7 @@ struct abx500_maxim_parameters {
};
/**
- * struct abx500_battery_type - different batteries supported
+ * struct ab8500_battery_type - different batteries supported
* @name: battery technology
* @resis_high: battery upper resistance limit
* @resis_low: battery lower resistance limit
@@ -400,7 +400,7 @@ struct abx500_maxim_parameters {
* @n_batres_tbl_elements number of elements in the batres_tbl
* @batres_tbl battery internal resistance vs temperature table
*/
-struct abx500_battery_type {
+struct ab8500_battery_type {
int name;
int resis_high;
int resis_low;
@@ -421,22 +421,22 @@ struct abx500_battery_type {
int low_high_vol_lvl;
int battery_resistance;
int n_temp_tbl_elements;
- const struct abx500_res_to_temp *r_to_t_tbl;
+ const struct ab8500_res_to_temp *r_to_t_tbl;
int n_v_cap_tbl_elements;
- const struct abx500_v_to_cap *v_to_cap_tbl;
+ const struct ab8500_v_to_cap *v_to_cap_tbl;
int n_batres_tbl_elements;
const struct batres_vs_temp *batres_tbl;
};
/**
- * struct abx500_bm_capacity_levels - abx500 capacity level data
+ * struct ab8500_bm_capacity_levels - ab8500 capacity level data
* @critical: critical capacity level in percent
* @low: low capacity level in percent
* @normal: normal capacity level in percent
* @high: high capacity level in percent
* @full: full capacity level in percent
*/
-struct abx500_bm_capacity_levels {
+struct ab8500_bm_capacity_levels {
int critical;
int low;
int normal;
@@ -445,13 +445,13 @@ struct abx500_bm_capacity_levels {
};
/**
- * struct abx500_bm_charger_parameters - Charger specific parameters
+ * struct ab8500_bm_charger_parameters - Charger specific parameters
* @usb_volt_max: maximum allowed USB charger voltage in mV
* @usb_curr_max: maximum allowed USB charger current in mA
* @ac_volt_max: maximum allowed AC charger voltage in mV
* @ac_curr_max: maximum allowed AC charger current in mA
*/
-struct abx500_bm_charger_parameters {
+struct ab8500_bm_charger_parameters {
int usb_volt_max;
int usb_curr_max;
int ac_volt_max;
@@ -459,7 +459,7 @@ struct abx500_bm_charger_parameters {
};
/**
- * struct abx500_bm_data - abx500 battery management data
+ * struct ab8500_bm_data - ab8500 battery management data
* @temp_under under this temp, charging is stopped
* @temp_low between this temp and temp_under charging is reduced
* @temp_high between this temp and temp_over charging is reduced
@@ -473,7 +473,7 @@ struct abx500_bm_charger_parameters {
* @bkup_bat_i current which we charge the backup battery with
* @no_maintenance indicates that maintenance charging is disabled
* @capacity_scaling indicates whether capacity scaling is to be used
- * @abx500_adc_therm placement of thermistor, batctrl or battemp adc
+ * @ab8500_adc_therm placement of thermistor, batctrl or battemp adc
* @chg_unknown_bat flag to enable charging of unknown batteries
* @enable_overshoot flag to enable VBAT overshoot control
* @auto_trig flag to enable auto adc trigger
@@ -494,7 +494,7 @@ struct abx500_bm_charger_parameters {
* @chg_params charger parameters
* @fg_params fuel gauge parameters
*/
-struct abx500_bm_data {
+struct ab8500_bm_data {
int temp_under;
int temp_low;
int temp_high;
@@ -511,7 +511,7 @@ struct abx500_bm_data {
bool chg_unknown_bat;
bool enable_overshoot;
bool auto_trig;
- enum abx500_adc_therm adc_therm;
+ enum ab8500_adc_therm adc_therm;
int fg_res;
int n_btypes;
int batt_id;
@@ -523,11 +523,11 @@ struct abx500_bm_data {
int n_chg_in_curr;
int *chg_output_curr;
int *chg_input_curr;
- const struct abx500_maxim_parameters *maxi;
- const struct abx500_bm_capacity_levels *cap_levels;
- struct abx500_battery_type *bat_type;
- const struct abx500_bm_charger_parameters *chg_params;
- const struct abx500_fg_parameters *fg_params;
+ const struct ab8500_maxim_parameters *maxi;
+ const struct ab8500_bm_capacity_levels *cap_levels;
+ struct ab8500_battery_type *bat_type;
+ const struct ab8500_bm_charger_parameters *chg_params;
+ const struct ab8500_fg_parameters *fg_params;
};
enum {
@@ -561,160 +561,7 @@ struct batres_vs_temp {
/* Forward declaration */
struct ab8500_fg;
-/**
- * struct ab8500_fg_parameters - Fuel gauge algorithm parameters, in seconds
- * if not specified
- * @recovery_sleep_timer: Time between measurements while recovering
- * @recovery_total_time: Total recovery time
- * @init_timer: Measurement interval during startup
- * @init_discard_time: Time we discard voltage measurement at startup
- * @init_total_time: Total init time during startup
- * @high_curr_time: Time current has to be high to go to recovery
- * @accu_charging: FG accumulation time while charging
- * @accu_high_curr: FG accumulation time in high current mode
- * @high_curr_threshold: High current threshold, in mA
- * @lowbat_threshold: Low battery threshold, in mV
- * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0
- * Resolution in 50 mV step.
- * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1
- * Resolution in 50 mV step.
- * @user_cap_limit Capacity reported from user must be within this
- * limit to be considered as sane, in percentage
- * points.
- * @maint_thres This is the threshold where we stop reporting
- * battery full while in maintenance, in per cent
- * @pcut_enable: Enable power cut feature in ab8505
- * @pcut_max_time: Max time threshold
- * @pcut_flag_time: Flagtime threshold
- * @pcut_max_restart: Max number of restarts
- * @pcut_debunce_time: Sets battery debounce time
- */
-struct ab8500_fg_parameters {
- int recovery_sleep_timer;
- int recovery_total_time;
- int init_timer;
- int init_discard_time;
- int init_total_time;
- int high_curr_time;
- int accu_charging;
- int accu_high_curr;
- int high_curr_threshold;
- int lowbat_threshold;
- int battok_falling_th_sel0;
- int battok_raising_th_sel1;
- int user_cap_limit;
- int maint_thres;
- bool pcut_enable;
- u8 pcut_max_time;
- u8 pcut_flag_time;
- u8 pcut_max_restart;
- u8 pcut_debunce_time;
-};
-
-/**
- * struct ab8500_charger_maximization - struct used by the board config.
- * @use_maxi: Enable maximization for this battery type
- * @maxi_chg_curr: Maximum charger current allowed
- * @maxi_wait_cycles: cycles to wait before setting charger current
- * @charger_curr_step delta between two charger current settings (mA)
- */
-struct ab8500_maxim_parameters {
- bool ena_maxi;
- int chg_curr;
- int wait_cycles;
- int charger_curr_step;
-};
-
-/**
- * struct ab8500_bm_capacity_levels - ab8500 capacity level data
- * @critical: critical capacity level in percent
- * @low: low capacity level in percent
- * @normal: normal capacity level in percent
- * @high: high capacity level in percent
- * @full: full capacity level in percent
- */
-struct ab8500_bm_capacity_levels {
- int critical;
- int low;
- int normal;
- int high;
- int full;
-};
-
-/**
- * struct ab8500_bm_charger_parameters - Charger specific parameters
- * @usb_volt_max: maximum allowed USB charger voltage in mV
- * @usb_curr_max: maximum allowed USB charger current in mA
- * @ac_volt_max: maximum allowed AC charger voltage in mV
- * @ac_curr_max: maximum allowed AC charger current in mA
- */
-struct ab8500_bm_charger_parameters {
- int usb_volt_max;
- int usb_curr_max;
- int ac_volt_max;
- int ac_curr_max;
-};
-
-/**
- * struct ab8500_bm_data - ab8500 battery management data
- * @temp_under under this temp, charging is stopped
- * @temp_low between this temp and temp_under charging is reduced
- * @temp_high between this temp and temp_over charging is reduced
- * @temp_over over this temp, charging is stopped
- * @temp_interval_chg temperature measurement interval in s when charging
- * @temp_interval_nochg temperature measurement interval in s when not charging
- * @main_safety_tmr_h safety timer for main charger
- * @usb_safety_tmr_h safety timer for usb charger
- * @bkup_bat_v voltage which we charge the backup battery with
- * @bkup_bat_i current which we charge the backup battery with
- * @no_maintenance indicates that maintenance charging is disabled
- * @capacity_scaling indicates whether capacity scaling is to be used
- * @adc_therm placement of thermistor, batctrl or battemp adc
- * @chg_unknown_bat flag to enable charging of unknown batteries
- * @enable_overshoot flag to enable VBAT overshoot control
- * @fg_res resistance of FG resistor in 0.1mOhm
- * @n_btypes number of elements in array bat_type
- * @batt_id index of the identified battery in array bat_type
- * @interval_charging charge alg cycle period time when charging (sec)
- * @interval_not_charging charge alg cycle period time when not charging (sec)
- * @temp_hysteresis temperature hysteresis
- * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm)
- * @maxi: maximization parameters
- * @cap_levels capacity in percent for the different capacity levels
- * @bat_type table of supported battery types
- * @chg_params charger parameters
- * @fg_params fuel gauge parameters
- */
-struct ab8500_bm_data {
- int temp_under;
- int temp_low;
- int temp_high;
- int temp_over;
- int temp_interval_chg;
- int temp_interval_nochg;
- int main_safety_tmr_h;
- int usb_safety_tmr_h;
- int bkup_bat_v;
- int bkup_bat_i;
- bool no_maintenance;
- bool capacity_scaling;
- bool chg_unknown_bat;
- bool enable_overshoot;
- enum abx500_adc_therm adc_therm;
- int fg_res;
- int n_btypes;
- int batt_id;
- int interval_charging;
- int interval_not_charging;
- int temp_hysteresis;
- int gnd_lift_resistance;
- const struct ab8500_maxim_parameters *maxi;
- const struct ab8500_bm_capacity_levels *cap_levels;
- const struct ab8500_bm_charger_parameters *chg_params;
- const struct ab8500_fg_parameters *fg_params;
-};
-
-extern struct abx500_bm_data ab8500_bm_data;
+extern struct ab8500_bm_data ab8500_bm_data;
void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA);
struct ab8500_fg *ab8500_fg_get(void);
@@ -725,7 +572,7 @@ int ab8500_fg_inst_curr_started(struct ab8500_fg *di);
int ab8500_fg_inst_curr_done(struct ab8500_fg *di);
int ab8500_bm_of_probe(struct device *dev,
struct device_node *np,
- struct abx500_bm_data *bm);
+ struct ab8500_bm_data *bm);
extern struct platform_driver ab8500_fg_driver;
extern struct platform_driver ab8500_btemp_driver;
@@ -13,7 +13,7 @@
* Note that the res_to_temp table must be strictly sorted by falling resistance
* values to work.
*/
-const struct abx500_res_to_temp ab8500_temp_tbl_a_thermistor[] = {
+const struct ab8500_res_to_temp ab8500_temp_tbl_a_thermistor[] = {
{-5, 53407},
{ 0, 48594},
{ 5, 43804},
@@ -35,7 +35,7 @@ EXPORT_SYMBOL(ab8500_temp_tbl_a_thermistor);
const int ab8500_temp_tbl_a_size = ARRAY_SIZE(ab8500_temp_tbl_a_thermistor);
EXPORT_SYMBOL(ab8500_temp_tbl_a_size);
-const struct abx500_res_to_temp ab8500_temp_tbl_b_thermistor[] = {
+const struct ab8500_res_to_temp ab8500_temp_tbl_b_thermistor[] = {
{-5, 200000},
{ 0, 159024},
{ 5, 151921},
@@ -57,7 +57,7 @@ EXPORT_SYMBOL(ab8500_temp_tbl_b_thermistor);
const int ab8500_temp_tbl_b_size = ARRAY_SIZE(ab8500_temp_tbl_b_thermistor);
EXPORT_SYMBOL(ab8500_temp_tbl_b_size);
-static const struct abx500_v_to_cap cap_tbl_a_thermistor[] = {
+static const struct ab8500_v_to_cap cap_tbl_a_thermistor[] = {
{4171, 100},
{4114, 95},
{4009, 83},
@@ -80,7 +80,7 @@ static const struct abx500_v_to_cap cap_tbl_a_thermistor[] = {
{3247, 0},
};
-static const struct abx500_v_to_cap cap_tbl_b_thermistor[] = {
+static const struct ab8500_v_to_cap cap_tbl_b_thermistor[] = {
{4161, 100},
{4124, 98},
{4044, 90},
@@ -103,7 +103,7 @@ static const struct abx500_v_to_cap cap_tbl_b_thermistor[] = {
{3250, 0},
};
-static const struct abx500_v_to_cap cap_tbl[] = {
+static const struct ab8500_v_to_cap cap_tbl[] = {
{4186, 100},
{4163, 99},
{4114, 95},
@@ -134,7 +134,7 @@ static const struct abx500_v_to_cap cap_tbl[] = {
* Note that the res_to_temp table must be strictly sorted by falling
* resistance values to work.
*/
-static const struct abx500_res_to_temp temp_tbl[] = {
+static const struct ab8500_res_to_temp temp_tbl[] = {
{-5, 214834},
{ 0, 162943},
{ 5, 124820},
@@ -191,7 +191,7 @@ static const struct batres_vs_temp temp_to_batres_tbl_9100[] = {
{-20, 180},
};
-static struct abx500_battery_type bat_type_thermistor[] = {
+static struct ab8500_battery_type bat_type_thermistor[] = {
[BATTERY_UNKNOWN] = {
/* First element always represent the UNKNOWN battery */
.name = POWER_SUPPLY_TECHNOLOGY_UNKNOWN,
@@ -277,7 +277,7 @@ static struct abx500_battery_type bat_type_thermistor[] = {
},
};
-static struct abx500_battery_type bat_type_ext_thermistor[] = {
+static struct ab8500_battery_type bat_type_ext_thermistor[] = {
[BATTERY_UNKNOWN] = {
/* First element always represent the UNKNOWN battery */
.name = POWER_SUPPLY_TECHNOLOGY_UNKNOWN,
@@ -394,7 +394,7 @@ static struct abx500_battery_type bat_type_ext_thermistor[] = {
},
};
-static const struct abx500_bm_capacity_levels cap_levels = {
+static const struct ab8500_bm_capacity_levels cap_levels = {
.critical = 2,
.low = 10,
.normal = 70,
@@ -402,7 +402,7 @@ static const struct abx500_bm_capacity_levels cap_levels = {
.full = 100,
};
-static const struct abx500_fg_parameters fg = {
+static const struct ab8500_fg_parameters fg = {
.recovery_sleep_timer = 10,
.recovery_total_time = 100,
.init_timer = 1,
@@ -424,14 +424,14 @@ static const struct abx500_fg_parameters fg = {
.pcut_debounce_time = 2,
};
-static const struct abx500_maxim_parameters ab8500_maxi_params = {
+static const struct ab8500_maxim_parameters ab8500_maxi_params = {
.ena_maxi = true,
.chg_curr = 910,
.wait_cycles = 10,
.charger_curr_step = 100,
};
-static const struct abx500_bm_charger_parameters chg = {
+static const struct ab8500_bm_charger_parameters chg = {
.usb_volt_max = 5500,
.usb_curr_max = 1500,
.ac_volt_max = 7500,
@@ -456,7 +456,7 @@ static int ab8500_charge_input_curr_map[] = {
700, 800, 900, 1000, 1100, 1300, 1400, 1500,
};
-struct abx500_bm_data ab8500_bm_data = {
+struct ab8500_bm_data ab8500_bm_data = {
.temp_under = 3,
.temp_low = 8,
.temp_high = 43,
@@ -469,7 +469,7 @@ struct abx500_bm_data ab8500_bm_data = {
.bkup_bat_i = BUP_ICH_SEL_150UA,
.no_maintenance = false,
.capacity_scaling = false,
- .adc_therm = ABx500_ADC_THERM_BATCTRL,
+ .adc_therm = AB8500_ADC_THERM_BATCTRL,
.chg_unknown_bat = false,
.enable_overshoot = false,
.fg_res = 100,
@@ -492,7 +492,7 @@ struct abx500_bm_data ab8500_bm_data = {
int ab8500_bm_of_probe(struct device *dev,
struct device_node *np,
- struct abx500_bm_data *bm)
+ struct ab8500_bm_data *bm)
{
const struct batres_vs_temp *tmp_batres_tbl;
struct device_node *battery_node;
@@ -531,7 +531,7 @@ int ab8500_bm_of_probe(struct device *dev,
} else {
bm->n_btypes = 4;
bm->bat_type = bat_type_ext_thermistor;
- bm->adc_therm = ABx500_ADC_THERM_BATTEMP;
+ bm->adc_therm = AB8500_ADC_THERM_BATTEMP;
tmp_batres_tbl = temp_to_batres_tbl_ext_thermistor;
}
@@ -103,7 +103,7 @@ struct ab8500_btemp {
struct iio_channel *btemp_ball;
struct iio_channel *bat_ctrl;
struct ab8500_fg *fg;
- struct abx500_bm_data *bm;
+ struct ab8500_bm_data *bm;
struct power_supply *btemp_psy;
struct ab8500_btemp_events events;
struct ab8500_btemp_ranges btemp_ranges;
@@ -145,7 +145,7 @@ static int ab8500_btemp_batctrl_volt_to_res(struct ab8500_btemp *di,
return (450000 * (v_batctrl)) / (1800 - v_batctrl);
}
- if (di->bm->adc_therm == ABx500_ADC_THERM_BATCTRL) {
+ if (di->bm->adc_therm == AB8500_ADC_THERM_BATCTRL) {
/*
* If the battery has internal NTC, we use the current
* source to calculate the resistance.
@@ -207,7 +207,7 @@ static int ab8500_btemp_curr_source_enable(struct ab8500_btemp *di,
return 0;
/* Only do this for batteries with internal NTC */
- if (di->bm->adc_therm == ABx500_ADC_THERM_BATCTRL && enable) {
+ if (di->bm->adc_therm == AB8500_ADC_THERM_BATCTRL && enable) {
if (di->curr_source == BTEMP_BATCTRL_CURR_SRC_7UA)
curr = BAT_CTRL_7U_ENA;
@@ -240,7 +240,7 @@ static int ab8500_btemp_curr_source_enable(struct ab8500_btemp *di,
__func__);
goto disable_curr_source;
}
- } else if (di->bm->adc_therm == ABx500_ADC_THERM_BATCTRL && !enable) {
+ } else if (di->bm->adc_therm == AB8500_ADC_THERM_BATCTRL && !enable) {
dev_dbg(di->dev, "Disable BATCTRL curr source\n");
/* Write 0 to the curr bits */
@@ -418,7 +418,7 @@ static int ab8500_btemp_get_batctrl_res(struct ab8500_btemp *di)
* based on the NTC resistance.
*/
static int ab8500_btemp_res_to_temp(struct ab8500_btemp *di,
- const struct abx500_res_to_temp *tbl, int tbl_size, int res)
+ const struct ab8500_res_to_temp *tbl, int tbl_size, int res)
{
int i;
/*
@@ -458,7 +458,7 @@ static int ab8500_btemp_measure_temp(struct ab8500_btemp *di)
id = di->bm->batt_id;
- if (di->bm->adc_therm == ABx500_ADC_THERM_BATCTRL &&
+ if (di->bm->adc_therm == AB8500_ADC_THERM_BATCTRL &&
id != BATTERY_UNKNOWN) {
rbat = ab8500_btemp_get_batctrl_res(di);
@@ -527,7 +527,7 @@ static int ab8500_btemp_id(struct ab8500_btemp *di)
dev_dbg(di->dev, "Battery detected on %s"
" low %d < res %d < high: %d"
" index: %d\n",
- di->bm->adc_therm == ABx500_ADC_THERM_BATCTRL ?
+ di->bm->adc_therm == AB8500_ADC_THERM_BATCTRL ?
"BATCTRL" : "BATTEMP",
di->bm->bat_type[i].resis_low, res,
di->bm->bat_type[i].resis_high, i);
@@ -547,7 +547,7 @@ static int ab8500_btemp_id(struct ab8500_btemp *di)
* We only have to change current source if the
* detected type is Type 1.
*/
- if (di->bm->adc_therm == ABx500_ADC_THERM_BATCTRL &&
+ if (di->bm->adc_therm == AB8500_ADC_THERM_BATCTRL &&
di->bm->batt_id == 1) {
dev_dbg(di->dev, "Set BATCTRL current source to 20uA\n");
di->curr_source = BTEMP_BATCTRL_CURR_SRC_20UA;
@@ -249,7 +249,7 @@ struct ab8500_chargalg {
struct ab8500_chargalg_suspension_status susp_status;
struct ab8500 *parent;
struct ab8500_chargalg_current_step_status curr_status;
- struct abx500_bm_data *bm;
+ struct ab8500_bm_data *bm;
struct power_supply *chargalg_psy;
struct ux500_charger *ac_chg;
struct ux500_charger *usb_chg;
@@ -292,7 +292,7 @@ struct ab8500_charger {
struct iio_channel *adc_main_charger_c;
struct iio_channel *adc_vbus_v;
struct iio_channel *adc_usb_charger_c;
- struct abx500_bm_data *bm;
+ struct ab8500_bm_data *bm;
struct ab8500_charger_event_flags flags;
struct ab8500_charger_usb_state usb_state;
struct ab8500_charger_max_usb_in_curr max_usb_in_curr;
@@ -225,7 +225,7 @@ struct ab8500_fg {
struct ab8500_fg_avg_cap avg_cap;
struct ab8500 *parent;
struct iio_channel *main_bat_v;
- struct abx500_bm_data *bm;
+ struct ab8500_bm_data *bm;
struct power_supply *fg_psy;
struct workqueue_struct *fg_wq;
struct delayed_work fg_periodic_work;
@@ -854,7 +854,7 @@ static int ab8500_fg_bat_voltage(struct ab8500_fg *di)
static int ab8500_fg_volt_to_capacity(struct ab8500_fg *di, int voltage)
{
int i, tbl_size;
- const struct abx500_v_to_cap *tbl;
+ const struct ab8500_v_to_cap *tbl;
int cap = 0;
tbl = di->bm->bat_type[di->bm->batt_id].v_to_cap_tbl;
@@ -2233,7 +2233,7 @@ static int ab8500_fg_get_ext_psy_data(struct device *dev, void *data)
case POWER_SUPPLY_TYPE_BATTERY:
if (!di->flags.batt_id_received &&
di->bm->batt_id != BATTERY_UNKNOWN) {
- const struct abx500_battery_type *b;
+ const struct ab8500_battery_type *b;
b = &(di->bm->bat_type[di->bm->batt_id]);
Drop the entire idea with abx500 being abstract and different from ab8500 in the AB8500 charging drivers. This rids the two identical definitions of a slew of structs in ab8500-bm.h and makes things less confusion and easier to understand. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- drivers/power/supply/ab8500-bm.h | 217 ++++--------------------- drivers/power/supply/ab8500_bmdata.c | 32 ++-- drivers/power/supply/ab8500_btemp.c | 16 +- drivers/power/supply/ab8500_chargalg.c | 2 +- drivers/power/supply/ab8500_charger.c | 2 +- drivers/power/supply/ab8500_fg.c | 6 +- 6 files changed, 61 insertions(+), 214 deletions(-) -- 2.31.1