@@ -56,6 +56,19 @@ properties:
The POR value is 0x1000h. This number is in mA (e.g. 8064).
See the spec for more information about the InputCurrent (0x3fh) register.
+ ti,wdt-timeout:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Used to control and set the charger watchdog delay between consecutive
+ charge voltage and charge current commands.
+ This value must be:
+ 0 - disabled
+ 1 - 44 seconds
+ 2 - 88 seconds
+ 3 - 175 seconds
+ The POR value is 0x11 (3).
+ See the spec for more information about the ChargeOptions(0x12h) register.
+
ti,external-control:
type: boolean
description: |
@@ -45,6 +45,8 @@
/* ChargeOptions bits of interest */
#define BQ24735_CHARGE_OPT_CHG_DISABLE (1 << 0)
#define BQ24735_CHARGE_OPT_AC_PRESENT (1 << 4)
+#define BQ24735_CHARGE_OPT_WDT_OFFSET 13
+#define BQ24735_CHARGE_OPT_WDT (3 << BQ24735_CHARGE_OPT_WDT_OFFSET)
struct bq24735 {
struct power_supply *charger;
@@ -156,6 +158,20 @@ static int bq24735_config_charger(struct bq24735 *charger)
}
}
+ if (pdata->wdt_timeout) {
+ value = pdata->wdt_timeout;
+
+ ret = bq24735_update_word(charger->client, BQ24735_CHARGE_OPT,
+ BQ24735_CHARGE_OPT_WDT,
+ (value << BQ24735_CHARGE_OPT_WDT_OFFSET));
+ if (ret < 0) {
+ dev_err(&charger->client->dev,
+ "Failed to write watchdog timer: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
return 0;
}
@@ -347,6 +363,17 @@ static struct bq24735_platform *bq24735_parse_dt_data(struct i2c_client *client)
if (!ret)
pdata->input_current = val;
+ ret = of_property_read_u32(np, "ti,wdt-timeout", &val);
+ if (!ret) {
+ if (val <= 3) {
+ pdata->wdt_timeout = val;
+ } else {
+ dev_warn(&client->dev,
+ "Invalid value for ti,wdt-timeout: %d",
+ val);
+ }
+ }
+
pdata->ext_control = of_property_read_bool(np, "ti,external-control");
return pdata;
@@ -476,6 +503,27 @@ static int bq24735_charger_probe(struct i2c_client *client,
return 0;
if (!charger->poll_interval)
return 0;
+ if (charger->pdata->wdt_timeout) {
+ int wdt_ms;
+
+ switch (charger->pdata->wdt_timeout) {
+ case 1:
+ wdt_ms = 44000;
+ break;
+ case 2:
+ wdt_ms = 88000;
+ break;
+ case 3:
+ wdt_ms = 175000;
+ break;
+ }
+
+ if (charger->poll_interval > wdt_ms) {
+ dev_err(&client->dev,
+ "Poll interval greater than WDT timeout\n");
+ return -EINVAL;
+ }
+ }
ret = devm_delayed_work_autocancel(&client->dev, &charger->poll,
bq24735_poll);
@@ -12,6 +12,7 @@ struct bq24735_platform {
uint32_t charge_current;
uint32_t charge_voltage;
uint32_t input_current;
+ uint32_t wdt_timeout;
const char *name;
The BQ24735 charger allows the user to set the watchdog timer delay between two consecutives ChargeCurrent or ChargeVoltage command writes, if the IC doesn't receive any command before the timeout happens, the charge is turned off. This patch adds the support to the user to change the default/POR value with four discrete values: 0 - disabled 1 - enabled, 44 sec 2 - enabled, 88 sec 3 - enabled, 175 sec (default at POR) These are the options supported in the ChargeOptions register bits 13&14. Also, this patch make one additional check when poll-interval is set by the user: if the interval set is greater than the WDT timeout it'll fail during the probe stage, preventing the user to set non-compatible values between the two options. Signed-off-by: Bruno Meneguele <bmeneg@redhat.com> --- Changelog: v1 - corrected the type of new bq24735_platform member wdt_timeout .../bindings/power/supply/bq24735.yaml | 13 +++++ drivers/power/supply/bq24735-charger.c | 48 +++++++++++++++++++ include/linux/power/bq24735-charger.h | 1 + 3 files changed, 62 insertions(+)