mbox series

[RESEND,v2,0/9] imx: thermal: Allow trip point configuration from DT

Message ID 20220617071411.187542-1-francesco.dolcini@toradex.com
Headers show
Series imx: thermal: Allow trip point configuration from DT | expand

Message

Francesco Dolcini June 17, 2022, 7:14 a.m. UTC 
This series allows to specify the imx thermal drivers trip point from the device tree,
without this change the threshold are hard-coded and this might not be correct given the
thermal design of the final system.

This change is backward compatible with the existing device tree, and even
with this change in by default the thresholds are the same as before.

Toradex board are also updated to use a system-specific thresholds.

Discussion on the current design is here:
https://lore.kernel.org/all/4ba1d7d2-3e8c-ba60-37fd-9598f415c076@linaro.org/

One side note, after this change the dtbs checker starts complaining with this message

```
linux/arch/arm/boot/dts/imx6dl-alti6p.dtb: tempmon: '#thermal-sensor-cells' does not match any of the regexes: '^(automotive|commercial|extended-commercial|industrial)-thermal$', 'pinctrl-[0-9]+'
	From schema: linux/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
```

to my understanding this is just a side effect, '#thermal-sensor-cells' is not changed in
any way by this series. I can fix that, I wonder if I should remove the property from the
imx dtsi files or add it to the binding yaml definition, not sure about it.
Anybody can advise?

Changes in v2:
 - fix build error without CONFIG_THERMAL_OF
 - more verbose error reporting in case the dts is not correct
 - additional comment on the threshold fixup in case the passive threshold is
   higher than critical
 - while parsing the dts thermal, return immediately if the node is not there


Francesco Dolcini (9):
  dt-bindings: thermal: Define trips node in $defs
  thermal: thermal: Export OF trip helper function
  dt-bindings: thermal: imx: Add trips point
  imx: thermal: Configure trip point from DT
  ARM: dts: imx[67]: Add trips points
  ARM: dts: imx6qdl-apalis: Set CPU critical trip point
  ARM: dts: imx7-colibri: Set CPU critical trip point
  ARM: dts: imx6ull-colibri: Set CPU critical trip point
  ARM: dts: imx6qdl-colibri: Set CPU critical trip point

 .../bindings/thermal/imx-thermal.yaml         |  27 ++++
 .../bindings/thermal/thermal-zones.yaml       | 130 +++++++++---------
 arch/arm/boot/dts/imx-thermal.dtsi            |  61 ++++++++
 arch/arm/boot/dts/imx6qdl-apalis.dtsi         |  12 ++
 arch/arm/boot/dts/imx6qdl-colibri.dtsi        |  12 ++
 arch/arm/boot/dts/imx6qdl.dtsi                |   2 +
 arch/arm/boot/dts/imx6sl.dtsi                 |   2 +
 arch/arm/boot/dts/imx6sll.dtsi                |   2 +
 arch/arm/boot/dts/imx6sx.dtsi                 |   2 +
 arch/arm/boot/dts/imx6ul.dtsi                 |   2 +
 arch/arm/boot/dts/imx6ull-colibri.dtsi        |  12 ++
 arch/arm/boot/dts/imx7-colibri.dtsi           |  12 ++
 arch/arm/boot/dts/imx7s.dtsi                  |   2 +
 drivers/thermal/imx_thermal.c                 |  58 ++++++++
 drivers/thermal/thermal_core.h                |   7 +
 drivers/thermal/thermal_of.c                  |   5 +-
 16 files changed, 283 insertions(+), 65 deletions(-)
 create mode 100644 arch/arm/boot/dts/imx-thermal.dtsi

Comments

Francesco Dolcini June 20, 2022, 3:02 p.m. UTC | #1 
On Fri, Jun 17, 2022 at 06:06:40PM -0700, Krzysztof Kozlowski wrote:
> On 17/06/2022 00:14, Francesco Dolcini wrote:
> > This series allows to specify the imx thermal drivers trip point from the device tree,
> > without this change the threshold are hard-coded and this might not be correct given the
> > thermal design of the final system.
> 
> Why resending? What was wrong with your v2 to which I replied?

Wrong subject in the cover letter, I had v1 instead of v2.
I thought this was going to confuse people, therefore I resent.

My mistake to not have explicitly written the reason of the resend.

Francesco