diff mbox series

[v2,4/4] arm64: dts: qcom: sm8350-sagami: Wire up SDHCI2

Message ID 20221116123612.34302-4-konrad.dybcio@linaro.org
State Superseded
Headers show
Series [v2,1/4] dt-bindings: mmc: sdhci-msm: Document SM8350 SDHCI | expand

Commit Message

Konrad Dybcio Nov. 16, 2022, 12:36 p.m. UTC 
Adjust regulators, add required pin setup and finally enable SDHCI2
to get the SD Card slot going on Sagami Xperias.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
Changes in v2:
- drop stray newline

 .../dts/qcom/sm8350-sony-xperia-sagami.dtsi   | 29 ++++++++++++++++++-
 1 file changed, 28 insertions(+), 1 deletion(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
index a428ce31ab4e..6ae700e72d1e 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
@@ -312,7 +312,8 @@  pm8350c_l8: ldo8 {
 		pm8350c_l9: ldo9 {
 			regulator-name = "pm8350c_l9";
 			regulator-min-microvolt = <2960000>;
-			regulator-max-microvolt = <3008000>;
+			/* Originally max = 3008000 but SDHCI expects 2960000 */
+			regulator-max-microvolt = <2960000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 
@@ -558,6 +559,18 @@  &qupv3_id_2 {
 	status = "okay";
 };
 
+&sdhc_2 {
+	cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_default_state &sdc2_card_det_active>;
+	pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_sleep>;
+	vmmc-supply = <&pm8350c_l9>;
+	vqmmc-supply = <&pm8350c_l6>;
+	no-sdio;
+	no-mmc;
+	status = "okay";
+};
+
 &slpi {
 	status = "okay";
 	firmware-name = "qcom/sm8350/Sony/sagami/slpi.mbn";
@@ -782,6 +795,20 @@  ts_int_default: ts-int-default-state {
 		bias-disable;
 		input-enable;
 	};
+
+	sdc2_card_det_active: sd-card-det-active-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	sdc2_card_det_sleep: sd-card-det-sleep-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
 };
 
 /* BIG WARNING! DO NOT TOUCH UFS, YOUR DEVICE WILL DIE! */