| Message ID | 20201106022726.19831-10-takahiro.akashi@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | Add support UHS-II for GL9755 | expand |
On 6/11/20 4:27 am, AKASHI Takahiro wrote: > Add UHS-II related definitions in shdci.h and sdhci-uhs2.h. > > Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw> > Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> > --- > drivers/mmc/host/sdhci-uhs2.h | 210 ++++++++++++++++++++++++++++++++++ > drivers/mmc/host/sdhci.h | 73 +++++++++++- > 2 files changed, 282 insertions(+), 1 deletion(-) > create mode 100644 drivers/mmc/host/sdhci-uhs2.h > > diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h > new file mode 100644 > index 000000000000..3b157df9c89c > --- /dev/null > +++ b/drivers/mmc/host/sdhci-uhs2.h > @@ -0,0 +1,210 @@ > +/* SPDX-License-Identifier: GPL-2.0-or-later */ > +/* > + * linux/drivers/mmc/host/sdhci-uhs2.h - Secure Digital Host Controller > + * Interface driver > + * > + * Header file for Host Controller UHS2 related registers and I/O accessors. > + * > + * Copyright (C) 2014 Intel Corp, All Rights Reserved. > + */ > +#ifndef __SDHCI_UHS2_H > +#define __SDHCI_UHS2_H > + > +#include <linux/bits.h> > + > +/* > + * UHS-II Controller registers > + * 0x74 preset in sdhci.h > + * 0x80 > + * 0x84-0xB4 > + * 0xB8-0xCF > + * 0xE0-0xE7 > + */ > +/* UHS2 */ > +#define SDHCI_UHS2_BLOCK_SIZE 0x80 > +#define SDHCI_UHS2_MAKE_BLKSZ(dma, blksz) \ > + ((((dma) & 0x7) << 12) | ((blksz) & 0xFFF)) > + > +#define SDHCI_UHS2_BLOCK_COUNT 0x84 > + > +#define SDHCI_UHS2_CMD_PACKET 0x88 > +#define SDHCI_UHS2_CMD_PACK_MAX_LEN 20 > + > +#define SDHCI_UHS2_TRANS_MODE 0x9C > +#define SDHCI_UHS2_TRNS_DMA BIT(0) > +#define SDHCI_UHS2_TRNS_BLK_CNT_EN BIT(1) > +#define SDHCI_UHS2_TRNS_DATA_TRNS_WRT BIT(4) > +#define SDHCI_UHS2_TRNS_BLK_BYTE_MODE BIT(5) > +#define SDHCI_UHS2_TRNS_RES_R5 BIT(6) > +#define SDHCI_UHS2_TRNS_RES_ERR_CHECK_EN BIT(7) > +#define SDHCI_UHS2_TRNS_RES_INT_DIS BIT(8) > +#define SDHCI_UHS2_TRNS_WAIT_EBSY BIT(14) > +#define SDHCI_UHS2_TRNS_2L_HD BIT(15) > + > +#define SDHCI_UHS2_COMMAND 0x9E > +#define SDHCI_UHS2_COMMAND_SUB_CMD 0x0004 > +#define SDHCI_UHS2_COMMAND_DATA 0x0020 > +#define SDHCI_UHS2_COMMAND_TRNS_ABORT 0x0040 > +#define SDHCI_UHS2_COMMAND_CMD12 0x0080 > +#define SDHCI_UHS2_COMMAND_DORMANT 0x00C0 > +#define SDHCI_UHS2_COMMAND_PACK_LEN_MASK GENMASK(12,8) > +#define SDHCI_UHS2_COMMAND_PACK_LEN_SHIFT 8 > + > +#define SDHCI_UHS2_RESPONSE 0xA0 > +#define SDHCI_UHS2_RESPONSE_MAX_LEN 20 > + > +#define SDHCI_UHS2_MSG_SELECT 0xB4 > +#define SDHCI_UHS2_MSG_SELECT_CURR 0x0 > +#define SDHCI_UHS2_MSG_SELECT_ONE 0x1 > +#define SDHCI_UHS2_MSG_SELECT_TWO 0x2 > +#define SDHCI_UHS2_MSG_SELECT_THREE 0x3 > + > +#define SDHCI_UHS2_MSG 0xB8 > + > +#define SDHCI_UHS2_DEV_INT_STATUS 0xBC > + > +#define SDHCI_UHS2_DEV_SELECT 0xBE > +#define SDHCI_UHS2_DEV_SELECT_DEV_SEL_MASK GENMASK(3,0) > +#define SDHCI_UHS2_DEV_SELECT_INT_MSG_EN BIT(7) > + > +#define SDHCI_UHS2_DEV_INT_CODE 0xBF > + > +#define SDHCI_UHS2_SW_RESET 0xC0 > +#define SDHCI_UHS2_SW_RESET_FULL 0x0001 > +#define SDHCI_UHS2_SW_RESET_SD 0x0002 > + > +#define SDHCI_UHS2_TIMER_CTRL 0xC2 > +#define SDHCI_UHS2_TIMER_CTRL_DEADLOCK_SHIFT 4 > + > +#define SDHCI_UHS2_ERR_INT_STATUS 0xC4 > +#define SDHCI_UHS2_ERR_INT_STATUS_EN 0xC8 > +#define SDHCI_UHS2_ERR_INT_SIG_EN 0xCC > +#define SDHCI_UHS2_ERR_INT_STATUS_HEADER BIT(0) > +#define SDHCI_UHS2_ERR_INT_STATUS_RES BIT(1) > +#define SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP BIT(2) > +#define SDHCI_UHS2_ERR_INT_STATUS_CRC BIT(3) > +#define SDHCI_UHS2_ERR_INT_STATUS_FRAME BIT(4) > +#define SDHCI_UHS2_ERR_INT_STATUS_TID BIT(5) > +#define SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER BIT(7) > +#define SDHCI_UHS2_ERR_INT_STATUS_EBUSY BIT(8) > +#define SDHCI_UHS2_ERR_INT_STATUS_ADMA BIT(15) > +#define SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT BIT(16) > +#define SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT BIT(17) > +#define SDHCI_UHS2_ERR_INT_STATUS_VENDOR BIT(27) > +#define SDHCI_UHS2_ERR_INT_STATUS_MASK \ > + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \ > + SDHCI_UHS2_ERR_INT_STATUS_RES | \ > + SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \ > + SDHCI_UHS2_ERR_INT_STATUS_CRC | \ > + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \ > + SDHCI_UHS2_ERR_INT_STATUS_TID | \ > + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \ > + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \ > + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \ > + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT | \ > + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT) > +#define SDHCI_UHS2_ERR_INT_STATUS_CMD_MASK \ > + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \ > + SDHCI_UHS2_ERR_INT_STATUS_RES | \ > + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \ > + SDHCI_UHS2_ERR_INT_STATUS_TID | \ > + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT) > +/* CRC Error occurs during a packet receiving */ > +#define SDHCI_UHS2_ERR_INT_STATUS_DATA_MASK \ > + (SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \ > + SDHCI_UHS2_ERR_INT_STATUS_CRC | \ > + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \ > + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \ > + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \ > + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT) > + > +#define SDHCI_UHS2_SET_PTR 0xE0 > +#define SDHCI_UHS2_GEN_SET_POWER_LOW 0x0001 > +#define SDHCI_UHS2_GEN_SET_N_LANES_POS 8 > +#define SDHCI_UHS2_GEN_SET_2L_FD_HD 0x0 > +#define SDHCI_UHS2_GEN_SET_2D1U_FD 0x2 > +#define SDHCI_UHS2_GEN_SET_1D2U_FD 0x3 > +#define SDHCI_UHS2_GEN_SET_2D2U_FD 0x4 > + > +#define SDHCI_UHS2_PHY_SET_SPEED_POS 6 > +#define SDHCI_UHS2_PHY_SET_HIBER_EN BIT(12) > +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_MASK GENMASK(19,16) > +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_POS 16 > +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_MASK GENMASK(23,20) > +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_POS 20 > + > +#define SDHCI_UHS2_TRAN_SET_N_FCU_MASK GENMASK(15,8) > +#define SDHCI_UHS2_TRAN_SET_N_FCU_POS 8 > +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_MASK GENMASK(17,16) > +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_POS 16 > + > +#define SDHCI_UHS2_TRAN_SET_1_N_DAT_GAP_MASK GENMASK(7,0) > + > +#define SDHCI_UHS2_HOST_CAPS_PTR 0xE2 > +#define SDHCI_UHS2_HOST_CAPS_GEN_OFFSET 0 > +#define SDHCI_UHS2_HOST_CAPS_GEN_DAP_MASK GENMASK(3,0) > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_MASK GENMASK(7,4) > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP(gap) ((gap) * 360) > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_SHIFT 4 > +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_MASK GENMASK(13,8) > +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_SHIFT 8 > +#define SDHCI_UHS2_HOST_CAPS_GEN_2L_HD_FD 1 > +#define SDHCI_UHS2_HOST_CAPS_GEN_2D1U_FD 2 > +#define SDHCI_UHS2_HOST_CAPS_GEN_1D2U_FD 4 > +#define SDHCI_UHS2_HOST_CAPS_GEN_2D2U_FD 8 > +#define SDHCI_UHS2_HOST_CAPS_GEN_ADDR_64 BIT(14) > +#define SDHCI_UHS2_HOST_CAPS_GEN_BOOT BIT(15) > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_MASK GENMASK(17,16) > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_SHIFT 16 > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_RMV 0 > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB 1 > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB_RMV 2 > +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_MASK GENMASK(21,18) > +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_SHIFT 18 > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_MASK GENMASK(23,22) > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_SHIFT 22 > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_P2P 0 > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_RING 1 > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB 2 > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB_RING 3 > + > +#define SDHCI_UHS2_HOST_CAPS_PHY_OFFSET 4 > +#define SDHCI_UHS2_HOST_CAPS_PHY_REV_MASK GENMASK(5,0) > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_MASK GENMASK(7,6) > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_SHIFT 6 > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_A 0 > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_B 1 > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_MASK GENMASK(19,16) > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_SHIFT 16 > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_MASK GENMASK(23,20) > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_SHIFT 20 > +#define SDHCI_UHS2_HOST_CAPS_TRAN_OFFSET 8 > +#define SDHCI_UHS2_HOST_CAPS_TRAN_LINK_REV_MASK GENMASK(5,0) > +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_MASK GENMASK(15,8) > +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_SHIFT 8 > +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_MASK GENMASK(18,16) > +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_SHIFT 16 > +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_MASK GENMASK(31,20) > +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_SHIFT 20 > + > +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_OFFSET 12 > +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_N_DATA_GAP_MASK GENMASK(7,0) > + > +#define SDHCI_UHS2_TEST_PTR 0xE4 > +#define SDHCI_UHS2_TEST_ERR_HEADER BIT(0) > +#define SDHCI_UHS2_TEST_ERR_RES BIT(1) > +#define SDHCI_UHS2_TEST_ERR_RETRY_EXP BIT(2) > +#define SDHCI_UHS2_TEST_ERR_CRC BIT(3) > +#define SDHCI_UHS2_TEST_ERR_FRAME BIT(4) > +#define SDHCI_UHS2_TEST_ERR_TID BIT(5) > +#define SDHCI_UHS2_TEST_ERR_UNRECOVER BIT(7) > +#define SDHCI_UHS2_TEST_ERR_EBUSY BIT(8) > +#define SDHCI_UHS2_TEST_ERR_ADMA BIT(15) > +#define SDHCI_UHS2_TEST_ERR_RES_TIMEOUT BIT(16) > +#define SDHCI_UHS2_TEST_ERR_DEADLOCK_TIMEOUT BIT(17) > +#define SDHCI_UHS2_TEST_ERR_VENDOR BIT(27) > + > +#define SDHCI_UHS2_EMBED_CTRL 0xE6 > +#define SDHCI_UHS2_VENDOR 0xE8 > + > +#endif /* __SDHCI_UHS2_H */ > diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h > index 0770c036e2ff..d9d7a76cedc1 100644 > --- a/drivers/mmc/host/sdhci.h > +++ b/drivers/mmc/host/sdhci.h > @@ -43,8 +43,27 @@ > #define SDHCI_TRNS_READ 0x10 > #define SDHCI_TRNS_MULTI 0x20 > > +/* > + * Defined in Host Version 4.10. > + * 1 - R5 (SDIO) > + * 0 - R1 (Memory) > + */ > +#define SDHCI_TRNS_RES_TYPE 0x40 > +#define SDHCI_TRNS_RES_ERR_CHECK 0x80 > +#define SDHCI_TRNS_RES_INT_DIS 0x0100 > + > #define SDHCI_COMMAND 0x0E > #define SDHCI_CMD_RESP_MASK 0x03 > + > +/* > + * Host Version 4.10 adds this bit to distinguish a main command or > + * sub command. > + * CMD53(SDIO) - main command > + * CMD52(SDIO) - sub command which doesn't have data block or doesn't > + * indicate busy. > + */ > +#define SDHCI_CMD_SUB_CMD 0x04 > + > #define SDHCI_CMD_CRC 0x08 > #define SDHCI_CMD_INDEX 0x10 > #define SDHCI_CMD_DATA 0x20 > @@ -60,11 +79,19 @@ > > #define SDHCI_RESPONSE 0x10 > > +#define SDHCI_RESPONSE_CM_TRAN_ABORT_OFFSET 0x10 > +#define SDHCI_RESPONSE_CM_TRAN_ABORT_SIZE 4 > +#define SDHCI_RESPONSE_SD_TRAN_ABORT_OFFSET 0x18 > +#define SDHCI_RESPONSE_SD_TRAN_ABORT_SIZE 8 I would prefer to have all the UHS2 definitions in sdhci-uhs2. If they belong to an existing register, just put a comment saying what register. > + > #define SDHCI_BUFFER 0x20 > > #define SDHCI_PRESENT_STATE 0x24 > #define SDHCI_CMD_INHIBIT 0x00000001 > #define SDHCI_DATA_INHIBIT 0x00000002 > + > +#define SDHCI_DATA_HIGH_LVL_MASK 0x000000F0 > + > #define SDHCI_DOING_WRITE 0x00000100 > #define SDHCI_DOING_READ 0x00000200 > #define SDHCI_SPACE_AVAILABLE 0x00000400 > @@ -80,6 +107,13 @@ > #define SDHCI_DATA_0_LVL_MASK 0x00100000 > #define SDHCI_CMD_LVL 0x01000000 > > +#define SDHCI_HOST_REGULATOR_STABLE 0x02000000 > +#define SDHCI_CMD_NOT_ISSUE_ERR 0x08000000 > +#define SDHCI_SUB_CMD_STATUS 0x10000000 > +#define SDHCI_UHS2_IN_DORMANT_STATE 0x20000000 > +#define SDHCI_UHS2_LANE_SYNC 0x40000000 > +#define SDHCI_UHS2_IF_DETECT 0x80000000 > + > #define SDHCI_HOST_CONTROL 0x28 > #define SDHCI_CTRL_LED 0x01 > #define SDHCI_CTRL_4BITBUS 0x02 > @@ -100,6 +134,11 @@ > #define SDHCI_POWER_300 0x0C > #define SDHCI_POWER_330 0x0E > > +/* VDD2 - UHS2 */ > +#define SDHCI_VDD2_POWER_ON 0x10 > +#define SDHCI_VDD2_POWER_180 0xA0 > +#define SDHCI_VDD2_POWER_120 0x80 > + > #define SDHCI_BLOCK_GAP_CONTROL 0x2A > > #define SDHCI_WAKE_UP_CONTROL 0x2B > @@ -110,7 +149,7 @@ > #define SDHCI_CLOCK_CONTROL 0x2C > #define SDHCI_DIVIDER_SHIFT 8 > #define SDHCI_DIVIDER_HI_SHIFT 6 > -#define SDHCI_DIV_MASK 0xFF > +#define SDHCI_DIV_MASK 0xFF > #define SDHCI_DIV_MASK_LEN 8 > #define SDHCI_DIV_HI_MASK 0x300 > #define SDHCI_PROG_CLOCK_MODE 0x0020 > @@ -139,6 +178,10 @@ > #define SDHCI_INT_CARD_REMOVE 0x00000080 > #define SDHCI_INT_CARD_INT 0x00000100 > #define SDHCI_INT_RETUNE 0x00001000 > + > +/* Host Version 4.10 */ > +#define SDHCI_INT_FX_EVENT 0x00002000 > + > #define SDHCI_INT_CQE 0x00004000 > #define SDHCI_INT_ERROR 0x00008000 > #define SDHCI_INT_TIMEOUT 0x00010000 > @@ -152,6 +195,9 @@ > #define SDHCI_INT_AUTO_CMD_ERR 0x01000000 > #define SDHCI_INT_ADMA_ERROR 0x02000000 > > +/* Host Version 4.0 */ > +#define SDHCI_INT_RESPONSE_ERROR 0x08000000 > + > #define SDHCI_INT_NORMAL_MASK 0x00007FFF > #define SDHCI_INT_ERROR_MASK 0xFFFF8000 > > @@ -178,6 +224,9 @@ > #define SDHCI_AUTO_CMD_END_BIT 0x00000008 > #define SDHCI_AUTO_CMD_INDEX 0x00000010 > > +/* Host Version 4.10 */ > +#define SDHCI_ACMD_RESPONSE_ERROR 0x0020 > + > #define SDHCI_HOST_CONTROL2 0x3E > #define SDHCI_CTRL_UHS_MASK 0x0007 > #define SDHCI_CTRL_UHS_SDR12 0x0000 > @@ -186,6 +235,7 @@ > #define SDHCI_CTRL_UHS_SDR104 0x0003 > #define SDHCI_CTRL_UHS_DDR50 0x0004 > #define SDHCI_CTRL_HS400 0x0005 /* Non-standard */ > +#define SDHCI_CTRL_UHS_2 0x0007 /* UHS-2 */ > #define SDHCI_CTRL_VDD_180 0x0008 > #define SDHCI_CTRL_DRV_TYPE_MASK 0x0030 > #define SDHCI_CTRL_DRV_TYPE_B 0x0000 > @@ -194,9 +244,12 @@ > #define SDHCI_CTRL_DRV_TYPE_D 0x0030 > #define SDHCI_CTRL_EXEC_TUNING 0x0040 > #define SDHCI_CTRL_TUNED_CLK 0x0080 > +#define SDHCI_CTRL_UHS2_INTERFACE_EN 0x0100 /* UHS-2 */ > +#define SDHCI_CTRL_ADMA2_LEN_MODE 0x0400 > #define SDHCI_CMD23_ENABLE 0x0800 > #define SDHCI_CTRL_V4_MODE 0x1000 > #define SDHCI_CTRL_64BIT_ADDR 0x2000 > +#define SDHCI_CTRL_ASYNC_INT_EN 0x4000 > #define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000 > > #define SDHCI_CAPABILITIES 0x40 > @@ -217,11 +270,13 @@ > #define SDHCI_CAN_VDD_180 0x04000000 > #define SDHCI_CAN_64BIT_V4 0x08000000 > #define SDHCI_CAN_64BIT 0x10000000 > +#define SDHCI_CAN_ASYNC_INT 0x20000000 > > #define SDHCI_CAPABILITIES_1 0x44 > #define SDHCI_SUPPORT_SDR50 0x00000001 > #define SDHCI_SUPPORT_SDR104 0x00000002 > #define SDHCI_SUPPORT_DDR50 0x00000004 > +#define SDHCI_SUPPORT_UHS2 0x00000008 /* UHS-2 support */ > #define SDHCI_DRIVER_TYPE_A 0x00000010 > #define SDHCI_DRIVER_TYPE_C 0x00000020 > #define SDHCI_DRIVER_TYPE_D 0x00000040 > @@ -230,19 +285,28 @@ > #define SDHCI_RETUNING_MODE_MASK GENMASK(15, 14) > #define SDHCI_CLOCK_MUL_MASK GENMASK(23, 16) > #define SDHCI_CAN_DO_ADMA3 0x08000000 > +#define SDHCI_SUPPORT_VDD2_180 0x10000000 /* UHS-2 1.8V VDD2 */ > +#define SDHCI_RSVD_FOR_VDD2 0x20000000 /* Rsvd for future VDD2 */ > #define SDHCI_SUPPORT_HS400 0x80000000 /* Non-standard */ > > #define SDHCI_MAX_CURRENT 0x48 > +#define SDHCI_MAX_CURRENT_1 0x4C > #define SDHCI_MAX_CURRENT_LIMIT GENMASK(7, 0) > #define SDHCI_MAX_CURRENT_330_MASK GENMASK(7, 0) > #define SDHCI_MAX_CURRENT_300_MASK GENMASK(15, 8) > #define SDHCI_MAX_CURRENT_180_MASK GENMASK(23, 16) > +#define SDHCI_MAX_CURRENT_VDD2_180_MASK GENMASK(7, 0) /* UHS2 */ > #define SDHCI_MAX_CURRENT_MULTIPLIER 4 > > /* 4C-4F reserved for more max current */ > > #define SDHCI_SET_ACMD12_ERROR 0x50 > +/* Host Version 4.10 */ > +#define SDHCI_SET_ACMD_RESPONSE_ERROR 0x20 > #define SDHCI_SET_INT_ERROR 0x52 > +/* Host Version 4.10 */ > +#define SDHCI_SET_INT_TUNING_ERROR 0x0400 > +#define SDHCI_SET_INT_RESPONSE_ERROR 0x0800 > > #define SDHCI_ADMA_ERROR 0x54 > > @@ -259,10 +323,16 @@ > #define SDHCI_PRESET_FOR_SDR104 0x6C > #define SDHCI_PRESET_FOR_DDR50 0x6E > #define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */ > + > +/* TODO: 0x74 is used for UHS2 in 4.10. How about HS400? */ > +/* UHS2 */ > +#define SDHCI_PRESET_FOR_UHS2 0x74 > #define SDHCI_PRESET_DRV_MASK GENMASK(15, 14) > #define SDHCI_PRESET_CLKGEN_SEL BIT(10) > #define SDHCI_PRESET_SDCLK_FREQ_MASK GENMASK(9, 0) > > +#define SDHCI_ADMA3_ADDRESS 0x78 > + > #define SDHCI_SLOT_INT_STATUS 0xFC > > #define SDHCI_HOST_VERSION 0xFE > @@ -652,6 +722,7 @@ struct sdhci_ops { > void (*request_done)(struct sdhci_host *host, > struct mmc_request *mrq); > void (*dump_vendor_regs)(struct sdhci_host *host); > + void (*dump_uhs2_regs)(struct sdhci_host *host); > }; > > #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS >
On Thu, Nov 26, 2020 at 10:15:29AM +0200, Adrian Hunter wrote: > On 6/11/20 4:27 am, AKASHI Takahiro wrote: > > Add UHS-II related definitions in shdci.h and sdhci-uhs2.h. > > > > Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw> > > Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> > > --- > > drivers/mmc/host/sdhci-uhs2.h | 210 ++++++++++++++++++++++++++++++++++ > > drivers/mmc/host/sdhci.h | 73 +++++++++++- > > 2 files changed, 282 insertions(+), 1 deletion(-) > > create mode 100644 drivers/mmc/host/sdhci-uhs2.h > > > > diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h > > new file mode 100644 > > index 000000000000..3b157df9c89c > > --- /dev/null > > +++ b/drivers/mmc/host/sdhci-uhs2.h > > @@ -0,0 +1,210 @@ > > +/* SPDX-License-Identifier: GPL-2.0-or-later */ > > +/* > > + * linux/drivers/mmc/host/sdhci-uhs2.h - Secure Digital Host Controller > > + * Interface driver > > + * > > + * Header file for Host Controller UHS2 related registers and I/O accessors. > > + * > > + * Copyright (C) 2014 Intel Corp, All Rights Reserved. > > + */ > > +#ifndef __SDHCI_UHS2_H > > +#define __SDHCI_UHS2_H > > + > > +#include <linux/bits.h> > > + > > +/* > > + * UHS-II Controller registers > > + * 0x74 preset in sdhci.h > > + * 0x80 > > + * 0x84-0xB4 > > + * 0xB8-0xCF > > + * 0xE0-0xE7 > > + */ > > +/* UHS2 */ > > +#define SDHCI_UHS2_BLOCK_SIZE 0x80 > > +#define SDHCI_UHS2_MAKE_BLKSZ(dma, blksz) \ > > + ((((dma) & 0x7) << 12) | ((blksz) & 0xFFF)) > > + > > +#define SDHCI_UHS2_BLOCK_COUNT 0x84 > > + > > +#define SDHCI_UHS2_CMD_PACKET 0x88 > > +#define SDHCI_UHS2_CMD_PACK_MAX_LEN 20 > > + > > +#define SDHCI_UHS2_TRANS_MODE 0x9C > > +#define SDHCI_UHS2_TRNS_DMA BIT(0) > > +#define SDHCI_UHS2_TRNS_BLK_CNT_EN BIT(1) > > +#define SDHCI_UHS2_TRNS_DATA_TRNS_WRT BIT(4) > > +#define SDHCI_UHS2_TRNS_BLK_BYTE_MODE BIT(5) > > +#define SDHCI_UHS2_TRNS_RES_R5 BIT(6) > > +#define SDHCI_UHS2_TRNS_RES_ERR_CHECK_EN BIT(7) > > +#define SDHCI_UHS2_TRNS_RES_INT_DIS BIT(8) > > +#define SDHCI_UHS2_TRNS_WAIT_EBSY BIT(14) > > +#define SDHCI_UHS2_TRNS_2L_HD BIT(15) > > + > > +#define SDHCI_UHS2_COMMAND 0x9E > > +#define SDHCI_UHS2_COMMAND_SUB_CMD 0x0004 > > +#define SDHCI_UHS2_COMMAND_DATA 0x0020 > > +#define SDHCI_UHS2_COMMAND_TRNS_ABORT 0x0040 > > +#define SDHCI_UHS2_COMMAND_CMD12 0x0080 > > +#define SDHCI_UHS2_COMMAND_DORMANT 0x00C0 > > +#define SDHCI_UHS2_COMMAND_PACK_LEN_MASK GENMASK(12,8) > > +#define SDHCI_UHS2_COMMAND_PACK_LEN_SHIFT 8 > > + > > +#define SDHCI_UHS2_RESPONSE 0xA0 > > +#define SDHCI_UHS2_RESPONSE_MAX_LEN 20 > > + > > +#define SDHCI_UHS2_MSG_SELECT 0xB4 > > +#define SDHCI_UHS2_MSG_SELECT_CURR 0x0 > > +#define SDHCI_UHS2_MSG_SELECT_ONE 0x1 > > +#define SDHCI_UHS2_MSG_SELECT_TWO 0x2 > > +#define SDHCI_UHS2_MSG_SELECT_THREE 0x3 > > + > > +#define SDHCI_UHS2_MSG 0xB8 > > + > > +#define SDHCI_UHS2_DEV_INT_STATUS 0xBC > > + > > +#define SDHCI_UHS2_DEV_SELECT 0xBE > > +#define SDHCI_UHS2_DEV_SELECT_DEV_SEL_MASK GENMASK(3,0) > > +#define SDHCI_UHS2_DEV_SELECT_INT_MSG_EN BIT(7) > > + > > +#define SDHCI_UHS2_DEV_INT_CODE 0xBF > > + > > +#define SDHCI_UHS2_SW_RESET 0xC0 > > +#define SDHCI_UHS2_SW_RESET_FULL 0x0001 > > +#define SDHCI_UHS2_SW_RESET_SD 0x0002 > > + > > +#define SDHCI_UHS2_TIMER_CTRL 0xC2 > > +#define SDHCI_UHS2_TIMER_CTRL_DEADLOCK_SHIFT 4 > > + > > +#define SDHCI_UHS2_ERR_INT_STATUS 0xC4 > > +#define SDHCI_UHS2_ERR_INT_STATUS_EN 0xC8 > > +#define SDHCI_UHS2_ERR_INT_SIG_EN 0xCC > > +#define SDHCI_UHS2_ERR_INT_STATUS_HEADER BIT(0) > > +#define SDHCI_UHS2_ERR_INT_STATUS_RES BIT(1) > > +#define SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP BIT(2) > > +#define SDHCI_UHS2_ERR_INT_STATUS_CRC BIT(3) > > +#define SDHCI_UHS2_ERR_INT_STATUS_FRAME BIT(4) > > +#define SDHCI_UHS2_ERR_INT_STATUS_TID BIT(5) > > +#define SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER BIT(7) > > +#define SDHCI_UHS2_ERR_INT_STATUS_EBUSY BIT(8) > > +#define SDHCI_UHS2_ERR_INT_STATUS_ADMA BIT(15) > > +#define SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT BIT(16) > > +#define SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT BIT(17) > > +#define SDHCI_UHS2_ERR_INT_STATUS_VENDOR BIT(27) > > +#define SDHCI_UHS2_ERR_INT_STATUS_MASK \ > > + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \ > > + SDHCI_UHS2_ERR_INT_STATUS_RES | \ > > + SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \ > > + SDHCI_UHS2_ERR_INT_STATUS_CRC | \ > > + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \ > > + SDHCI_UHS2_ERR_INT_STATUS_TID | \ > > + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \ > > + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \ > > + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \ > > + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT | \ > > + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT) > > +#define SDHCI_UHS2_ERR_INT_STATUS_CMD_MASK \ > > + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \ > > + SDHCI_UHS2_ERR_INT_STATUS_RES | \ > > + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \ > > + SDHCI_UHS2_ERR_INT_STATUS_TID | \ > > + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT) > > +/* CRC Error occurs during a packet receiving */ > > +#define SDHCI_UHS2_ERR_INT_STATUS_DATA_MASK \ > > + (SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \ > > + SDHCI_UHS2_ERR_INT_STATUS_CRC | \ > > + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \ > > + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \ > > + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \ > > + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT) > > + > > +#define SDHCI_UHS2_SET_PTR 0xE0 > > +#define SDHCI_UHS2_GEN_SET_POWER_LOW 0x0001 > > +#define SDHCI_UHS2_GEN_SET_N_LANES_POS 8 > > +#define SDHCI_UHS2_GEN_SET_2L_FD_HD 0x0 > > +#define SDHCI_UHS2_GEN_SET_2D1U_FD 0x2 > > +#define SDHCI_UHS2_GEN_SET_1D2U_FD 0x3 > > +#define SDHCI_UHS2_GEN_SET_2D2U_FD 0x4 > > + > > +#define SDHCI_UHS2_PHY_SET_SPEED_POS 6 > > +#define SDHCI_UHS2_PHY_SET_HIBER_EN BIT(12) > > +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_MASK GENMASK(19,16) > > +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_POS 16 > > +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_MASK GENMASK(23,20) > > +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_POS 20 > > + > > +#define SDHCI_UHS2_TRAN_SET_N_FCU_MASK GENMASK(15,8) > > +#define SDHCI_UHS2_TRAN_SET_N_FCU_POS 8 > > +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_MASK GENMASK(17,16) > > +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_POS 16 > > + > > +#define SDHCI_UHS2_TRAN_SET_1_N_DAT_GAP_MASK GENMASK(7,0) > > + > > +#define SDHCI_UHS2_HOST_CAPS_PTR 0xE2 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_OFFSET 0 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_DAP_MASK GENMASK(3,0) > > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_MASK GENMASK(7,4) > > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP(gap) ((gap) * 360) > > +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_SHIFT 4 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_MASK GENMASK(13,8) > > +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_SHIFT 8 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_2L_HD_FD 1 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_2D1U_FD 2 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_1D2U_FD 4 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_2D2U_FD 8 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_ADDR_64 BIT(14) > > +#define SDHCI_UHS2_HOST_CAPS_GEN_BOOT BIT(15) > > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_MASK GENMASK(17,16) > > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_SHIFT 16 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_RMV 0 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB 1 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB_RMV 2 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_MASK GENMASK(21,18) > > +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_SHIFT 18 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_MASK GENMASK(23,22) > > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_SHIFT 22 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_P2P 0 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_RING 1 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB 2 > > +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB_RING 3 > > + > > +#define SDHCI_UHS2_HOST_CAPS_PHY_OFFSET 4 > > +#define SDHCI_UHS2_HOST_CAPS_PHY_REV_MASK GENMASK(5,0) > > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_MASK GENMASK(7,6) > > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_SHIFT 6 > > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_A 0 > > +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_B 1 > > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_MASK GENMASK(19,16) > > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_SHIFT 16 > > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_MASK GENMASK(23,20) > > +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_SHIFT 20 > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_OFFSET 8 > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_LINK_REV_MASK GENMASK(5,0) > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_MASK GENMASK(15,8) > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_SHIFT 8 > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_MASK GENMASK(18,16) > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_SHIFT 16 > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_MASK GENMASK(31,20) > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_SHIFT 20 > > + > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_OFFSET 12 > > +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_N_DATA_GAP_MASK GENMASK(7,0) > > + > > +#define SDHCI_UHS2_TEST_PTR 0xE4 > > +#define SDHCI_UHS2_TEST_ERR_HEADER BIT(0) > > +#define SDHCI_UHS2_TEST_ERR_RES BIT(1) > > +#define SDHCI_UHS2_TEST_ERR_RETRY_EXP BIT(2) > > +#define SDHCI_UHS2_TEST_ERR_CRC BIT(3) > > +#define SDHCI_UHS2_TEST_ERR_FRAME BIT(4) > > +#define SDHCI_UHS2_TEST_ERR_TID BIT(5) > > +#define SDHCI_UHS2_TEST_ERR_UNRECOVER BIT(7) > > +#define SDHCI_UHS2_TEST_ERR_EBUSY BIT(8) > > +#define SDHCI_UHS2_TEST_ERR_ADMA BIT(15) > > +#define SDHCI_UHS2_TEST_ERR_RES_TIMEOUT BIT(16) > > +#define SDHCI_UHS2_TEST_ERR_DEADLOCK_TIMEOUT BIT(17) > > +#define SDHCI_UHS2_TEST_ERR_VENDOR BIT(27) > > + > > +#define SDHCI_UHS2_EMBED_CTRL 0xE6 > > +#define SDHCI_UHS2_VENDOR 0xE8 > > + > > +#endif /* __SDHCI_UHS2_H */ > > diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h > > index 0770c036e2ff..d9d7a76cedc1 100644 > > --- a/drivers/mmc/host/sdhci.h > > +++ b/drivers/mmc/host/sdhci.h > > @@ -43,8 +43,27 @@ > > #define SDHCI_TRNS_READ 0x10 > > #define SDHCI_TRNS_MULTI 0x20 > > > > +/* > > + * Defined in Host Version 4.10. > > + * 1 - R5 (SDIO) > > + * 0 - R1 (Memory) > > + */ > > +#define SDHCI_TRNS_RES_TYPE 0x40 > > +#define SDHCI_TRNS_RES_ERR_CHECK 0x80 > > +#define SDHCI_TRNS_RES_INT_DIS 0x0100 > > + > > #define SDHCI_COMMAND 0x0E > > #define SDHCI_CMD_RESP_MASK 0x03 > > + > > +/* > > + * Host Version 4.10 adds this bit to distinguish a main command or > > + * sub command. > > + * CMD53(SDIO) - main command > > + * CMD52(SDIO) - sub command which doesn't have data block or doesn't > > + * indicate busy. > > + */ > > +#define SDHCI_CMD_SUB_CMD 0x04 > > + > > #define SDHCI_CMD_CRC 0x08 > > #define SDHCI_CMD_INDEX 0x10 > > #define SDHCI_CMD_DATA 0x20 > > @@ -60,11 +79,19 @@ > > > > #define SDHCI_RESPONSE 0x10 > > > > +#define SDHCI_RESPONSE_CM_TRAN_ABORT_OFFSET 0x10 > > +#define SDHCI_RESPONSE_CM_TRAN_ABORT_SIZE 4 > > +#define SDHCI_RESPONSE_SD_TRAN_ABORT_OFFSET 0x18 > > +#define SDHCI_RESPONSE_SD_TRAN_ABORT_SIZE 8 > > I would prefer to have all the UHS2 definitions in sdhci-uhs2. If they > belong to an existing register, just put a comment saying what register. I would disagree, but if you really want, I'd defer to you. -Takahiro Akashi > > > + > > #define SDHCI_BUFFER 0x20 > > > > #define SDHCI_PRESENT_STATE 0x24 > > #define SDHCI_CMD_INHIBIT 0x00000001 > > #define SDHCI_DATA_INHIBIT 0x00000002 > > + > > +#define SDHCI_DATA_HIGH_LVL_MASK 0x000000F0 > > + > > #define SDHCI_DOING_WRITE 0x00000100 > > #define SDHCI_DOING_READ 0x00000200 > > #define SDHCI_SPACE_AVAILABLE 0x00000400 > > @@ -80,6 +107,13 @@ > > #define SDHCI_DATA_0_LVL_MASK 0x00100000 > > #define SDHCI_CMD_LVL 0x01000000 > > > > +#define SDHCI_HOST_REGULATOR_STABLE 0x02000000 > > +#define SDHCI_CMD_NOT_ISSUE_ERR 0x08000000 > > +#define SDHCI_SUB_CMD_STATUS 0x10000000 > > +#define SDHCI_UHS2_IN_DORMANT_STATE 0x20000000 > > +#define SDHCI_UHS2_LANE_SYNC 0x40000000 > > +#define SDHCI_UHS2_IF_DETECT 0x80000000 > > + > > #define SDHCI_HOST_CONTROL 0x28 > > #define SDHCI_CTRL_LED 0x01 > > #define SDHCI_CTRL_4BITBUS 0x02 > > @@ -100,6 +134,11 @@ > > #define SDHCI_POWER_300 0x0C > > #define SDHCI_POWER_330 0x0E > > > > +/* VDD2 - UHS2 */ > > +#define SDHCI_VDD2_POWER_ON 0x10 > > +#define SDHCI_VDD2_POWER_180 0xA0 > > +#define SDHCI_VDD2_POWER_120 0x80 > > + > > #define SDHCI_BLOCK_GAP_CONTROL 0x2A > > > > #define SDHCI_WAKE_UP_CONTROL 0x2B > > @@ -110,7 +149,7 @@ > > #define SDHCI_CLOCK_CONTROL 0x2C > > #define SDHCI_DIVIDER_SHIFT 8 > > #define SDHCI_DIVIDER_HI_SHIFT 6 > > -#define SDHCI_DIV_MASK 0xFF > > +#define SDHCI_DIV_MASK 0xFF > > #define SDHCI_DIV_MASK_LEN 8 > > #define SDHCI_DIV_HI_MASK 0x300 > > #define SDHCI_PROG_CLOCK_MODE 0x0020 > > @@ -139,6 +178,10 @@ > > #define SDHCI_INT_CARD_REMOVE 0x00000080 > > #define SDHCI_INT_CARD_INT 0x00000100 > > #define SDHCI_INT_RETUNE 0x00001000 > > + > > +/* Host Version 4.10 */ > > +#define SDHCI_INT_FX_EVENT 0x00002000 > > + > > #define SDHCI_INT_CQE 0x00004000 > > #define SDHCI_INT_ERROR 0x00008000 > > #define SDHCI_INT_TIMEOUT 0x00010000 > > @@ -152,6 +195,9 @@ > > #define SDHCI_INT_AUTO_CMD_ERR 0x01000000 > > #define SDHCI_INT_ADMA_ERROR 0x02000000 > > > > +/* Host Version 4.0 */ > > +#define SDHCI_INT_RESPONSE_ERROR 0x08000000 > > + > > #define SDHCI_INT_NORMAL_MASK 0x00007FFF > > #define SDHCI_INT_ERROR_MASK 0xFFFF8000 > > > > @@ -178,6 +224,9 @@ > > #define SDHCI_AUTO_CMD_END_BIT 0x00000008 > > #define SDHCI_AUTO_CMD_INDEX 0x00000010 > > > > +/* Host Version 4.10 */ > > +#define SDHCI_ACMD_RESPONSE_ERROR 0x0020 > > + > > #define SDHCI_HOST_CONTROL2 0x3E > > #define SDHCI_CTRL_UHS_MASK 0x0007 > > #define SDHCI_CTRL_UHS_SDR12 0x0000 > > @@ -186,6 +235,7 @@ > > #define SDHCI_CTRL_UHS_SDR104 0x0003 > > #define SDHCI_CTRL_UHS_DDR50 0x0004 > > #define SDHCI_CTRL_HS400 0x0005 /* Non-standard */ > > +#define SDHCI_CTRL_UHS_2 0x0007 /* UHS-2 */ > > #define SDHCI_CTRL_VDD_180 0x0008 > > #define SDHCI_CTRL_DRV_TYPE_MASK 0x0030 > > #define SDHCI_CTRL_DRV_TYPE_B 0x0000 > > @@ -194,9 +244,12 @@ > > #define SDHCI_CTRL_DRV_TYPE_D 0x0030 > > #define SDHCI_CTRL_EXEC_TUNING 0x0040 > > #define SDHCI_CTRL_TUNED_CLK 0x0080 > > +#define SDHCI_CTRL_UHS2_INTERFACE_EN 0x0100 /* UHS-2 */ > > +#define SDHCI_CTRL_ADMA2_LEN_MODE 0x0400 > > #define SDHCI_CMD23_ENABLE 0x0800 > > #define SDHCI_CTRL_V4_MODE 0x1000 > > #define SDHCI_CTRL_64BIT_ADDR 0x2000 > > +#define SDHCI_CTRL_ASYNC_INT_EN 0x4000 > > #define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000 > > > > #define SDHCI_CAPABILITIES 0x40 > > @@ -217,11 +270,13 @@ > > #define SDHCI_CAN_VDD_180 0x04000000 > > #define SDHCI_CAN_64BIT_V4 0x08000000 > > #define SDHCI_CAN_64BIT 0x10000000 > > +#define SDHCI_CAN_ASYNC_INT 0x20000000 > > > > #define SDHCI_CAPABILITIES_1 0x44 > > #define SDHCI_SUPPORT_SDR50 0x00000001 > > #define SDHCI_SUPPORT_SDR104 0x00000002 > > #define SDHCI_SUPPORT_DDR50 0x00000004 > > +#define SDHCI_SUPPORT_UHS2 0x00000008 /* UHS-2 support */ > > #define SDHCI_DRIVER_TYPE_A 0x00000010 > > #define SDHCI_DRIVER_TYPE_C 0x00000020 > > #define SDHCI_DRIVER_TYPE_D 0x00000040 > > @@ -230,19 +285,28 @@ > > #define SDHCI_RETUNING_MODE_MASK GENMASK(15, 14) > > #define SDHCI_CLOCK_MUL_MASK GENMASK(23, 16) > > #define SDHCI_CAN_DO_ADMA3 0x08000000 > > +#define SDHCI_SUPPORT_VDD2_180 0x10000000 /* UHS-2 1.8V VDD2 */ > > +#define SDHCI_RSVD_FOR_VDD2 0x20000000 /* Rsvd for future VDD2 */ > > #define SDHCI_SUPPORT_HS400 0x80000000 /* Non-standard */ > > > > #define SDHCI_MAX_CURRENT 0x48 > > +#define SDHCI_MAX_CURRENT_1 0x4C > > #define SDHCI_MAX_CURRENT_LIMIT GENMASK(7, 0) > > #define SDHCI_MAX_CURRENT_330_MASK GENMASK(7, 0) > > #define SDHCI_MAX_CURRENT_300_MASK GENMASK(15, 8) > > #define SDHCI_MAX_CURRENT_180_MASK GENMASK(23, 16) > > +#define SDHCI_MAX_CURRENT_VDD2_180_MASK GENMASK(7, 0) /* UHS2 */ > > #define SDHCI_MAX_CURRENT_MULTIPLIER 4 > > > > /* 4C-4F reserved for more max current */ > > > > #define SDHCI_SET_ACMD12_ERROR 0x50 > > +/* Host Version 4.10 */ > > +#define SDHCI_SET_ACMD_RESPONSE_ERROR 0x20 > > #define SDHCI_SET_INT_ERROR 0x52 > > +/* Host Version 4.10 */ > > +#define SDHCI_SET_INT_TUNING_ERROR 0x0400 > > +#define SDHCI_SET_INT_RESPONSE_ERROR 0x0800 > > > > #define SDHCI_ADMA_ERROR 0x54 > > > > @@ -259,10 +323,16 @@ > > #define SDHCI_PRESET_FOR_SDR104 0x6C > > #define SDHCI_PRESET_FOR_DDR50 0x6E > > #define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */ > > + > > +/* TODO: 0x74 is used for UHS2 in 4.10. How about HS400? */ > > +/* UHS2 */ > > +#define SDHCI_PRESET_FOR_UHS2 0x74 > > #define SDHCI_PRESET_DRV_MASK GENMASK(15, 14) > > #define SDHCI_PRESET_CLKGEN_SEL BIT(10) > > #define SDHCI_PRESET_SDCLK_FREQ_MASK GENMASK(9, 0) > > > > +#define SDHCI_ADMA3_ADDRESS 0x78 > > + > > #define SDHCI_SLOT_INT_STATUS 0xFC > > > > #define SDHCI_HOST_VERSION 0xFE > > @@ -652,6 +722,7 @@ struct sdhci_ops { > > void (*request_done)(struct sdhci_host *host, > > struct mmc_request *mrq); > > void (*dump_vendor_regs)(struct sdhci_host *host); > > + void (*dump_uhs2_regs)(struct sdhci_host *host); > > }; > > > > #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS > > >
diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h new file mode 100644 index 000000000000..3b157df9c89c --- /dev/null +++ b/drivers/mmc/host/sdhci-uhs2.h @@ -0,0 +1,210 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* + * linux/drivers/mmc/host/sdhci-uhs2.h - Secure Digital Host Controller + * Interface driver + * + * Header file for Host Controller UHS2 related registers and I/O accessors. + * + * Copyright (C) 2014 Intel Corp, All Rights Reserved. + */ +#ifndef __SDHCI_UHS2_H +#define __SDHCI_UHS2_H + +#include <linux/bits.h> + +/* + * UHS-II Controller registers + * 0x74 preset in sdhci.h + * 0x80 + * 0x84-0xB4 + * 0xB8-0xCF + * 0xE0-0xE7 + */ +/* UHS2 */ +#define SDHCI_UHS2_BLOCK_SIZE 0x80 +#define SDHCI_UHS2_MAKE_BLKSZ(dma, blksz) \ + ((((dma) & 0x7) << 12) | ((blksz) & 0xFFF)) + +#define SDHCI_UHS2_BLOCK_COUNT 0x84 + +#define SDHCI_UHS2_CMD_PACKET 0x88 +#define SDHCI_UHS2_CMD_PACK_MAX_LEN 20 + +#define SDHCI_UHS2_TRANS_MODE 0x9C +#define SDHCI_UHS2_TRNS_DMA BIT(0) +#define SDHCI_UHS2_TRNS_BLK_CNT_EN BIT(1) +#define SDHCI_UHS2_TRNS_DATA_TRNS_WRT BIT(4) +#define SDHCI_UHS2_TRNS_BLK_BYTE_MODE BIT(5) +#define SDHCI_UHS2_TRNS_RES_R5 BIT(6) +#define SDHCI_UHS2_TRNS_RES_ERR_CHECK_EN BIT(7) +#define SDHCI_UHS2_TRNS_RES_INT_DIS BIT(8) +#define SDHCI_UHS2_TRNS_WAIT_EBSY BIT(14) +#define SDHCI_UHS2_TRNS_2L_HD BIT(15) + +#define SDHCI_UHS2_COMMAND 0x9E +#define SDHCI_UHS2_COMMAND_SUB_CMD 0x0004 +#define SDHCI_UHS2_COMMAND_DATA 0x0020 +#define SDHCI_UHS2_COMMAND_TRNS_ABORT 0x0040 +#define SDHCI_UHS2_COMMAND_CMD12 0x0080 +#define SDHCI_UHS2_COMMAND_DORMANT 0x00C0 +#define SDHCI_UHS2_COMMAND_PACK_LEN_MASK GENMASK(12,8) +#define SDHCI_UHS2_COMMAND_PACK_LEN_SHIFT 8 + +#define SDHCI_UHS2_RESPONSE 0xA0 +#define SDHCI_UHS2_RESPONSE_MAX_LEN 20 + +#define SDHCI_UHS2_MSG_SELECT 0xB4 +#define SDHCI_UHS2_MSG_SELECT_CURR 0x0 +#define SDHCI_UHS2_MSG_SELECT_ONE 0x1 +#define SDHCI_UHS2_MSG_SELECT_TWO 0x2 +#define SDHCI_UHS2_MSG_SELECT_THREE 0x3 + +#define SDHCI_UHS2_MSG 0xB8 + +#define SDHCI_UHS2_DEV_INT_STATUS 0xBC + +#define SDHCI_UHS2_DEV_SELECT 0xBE +#define SDHCI_UHS2_DEV_SELECT_DEV_SEL_MASK GENMASK(3,0) +#define SDHCI_UHS2_DEV_SELECT_INT_MSG_EN BIT(7) + +#define SDHCI_UHS2_DEV_INT_CODE 0xBF + +#define SDHCI_UHS2_SW_RESET 0xC0 +#define SDHCI_UHS2_SW_RESET_FULL 0x0001 +#define SDHCI_UHS2_SW_RESET_SD 0x0002 + +#define SDHCI_UHS2_TIMER_CTRL 0xC2 +#define SDHCI_UHS2_TIMER_CTRL_DEADLOCK_SHIFT 4 + +#define SDHCI_UHS2_ERR_INT_STATUS 0xC4 +#define SDHCI_UHS2_ERR_INT_STATUS_EN 0xC8 +#define SDHCI_UHS2_ERR_INT_SIG_EN 0xCC +#define SDHCI_UHS2_ERR_INT_STATUS_HEADER BIT(0) +#define SDHCI_UHS2_ERR_INT_STATUS_RES BIT(1) +#define SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP BIT(2) +#define SDHCI_UHS2_ERR_INT_STATUS_CRC BIT(3) +#define SDHCI_UHS2_ERR_INT_STATUS_FRAME BIT(4) +#define SDHCI_UHS2_ERR_INT_STATUS_TID BIT(5) +#define SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER BIT(7) +#define SDHCI_UHS2_ERR_INT_STATUS_EBUSY BIT(8) +#define SDHCI_UHS2_ERR_INT_STATUS_ADMA BIT(15) +#define SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT BIT(16) +#define SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT BIT(17) +#define SDHCI_UHS2_ERR_INT_STATUS_VENDOR BIT(27) +#define SDHCI_UHS2_ERR_INT_STATUS_MASK \ + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \ + SDHCI_UHS2_ERR_INT_STATUS_RES | \ + SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \ + SDHCI_UHS2_ERR_INT_STATUS_CRC | \ + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \ + SDHCI_UHS2_ERR_INT_STATUS_TID | \ + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \ + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \ + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \ + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT | \ + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT) +#define SDHCI_UHS2_ERR_INT_STATUS_CMD_MASK \ + (SDHCI_UHS2_ERR_INT_STATUS_HEADER | \ + SDHCI_UHS2_ERR_INT_STATUS_RES | \ + SDHCI_UHS2_ERR_INT_STATUS_FRAME | \ + SDHCI_UHS2_ERR_INT_STATUS_TID | \ + SDHCI_UHS2_ERR_INT_STATUS_RES_TIMEOUT) +/* CRC Error occurs during a packet receiving */ +#define SDHCI_UHS2_ERR_INT_STATUS_DATA_MASK \ + (SDHCI_UHS2_ERR_INT_STATUS_RETRY_EXP | \ + SDHCI_UHS2_ERR_INT_STATUS_CRC | \ + SDHCI_UHS2_ERR_INT_STATUS_UNRECOVER | \ + SDHCI_UHS2_ERR_INT_STATUS_EBUSY | \ + SDHCI_UHS2_ERR_INT_STATUS_ADMA | \ + SDHCI_UHS2_ERR_INT_STATUS_DEADLOCK_TIMEOUT) + +#define SDHCI_UHS2_SET_PTR 0xE0 +#define SDHCI_UHS2_GEN_SET_POWER_LOW 0x0001 +#define SDHCI_UHS2_GEN_SET_N_LANES_POS 8 +#define SDHCI_UHS2_GEN_SET_2L_FD_HD 0x0 +#define SDHCI_UHS2_GEN_SET_2D1U_FD 0x2 +#define SDHCI_UHS2_GEN_SET_1D2U_FD 0x3 +#define SDHCI_UHS2_GEN_SET_2D2U_FD 0x4 + +#define SDHCI_UHS2_PHY_SET_SPEED_POS 6 +#define SDHCI_UHS2_PHY_SET_HIBER_EN BIT(12) +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_MASK GENMASK(19,16) +#define SDHCI_UHS2_PHY_SET_N_LSS_SYN_POS 16 +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_MASK GENMASK(23,20) +#define SDHCI_UHS2_PHY_SET_N_LSS_DIR_POS 20 + +#define SDHCI_UHS2_TRAN_SET_N_FCU_MASK GENMASK(15,8) +#define SDHCI_UHS2_TRAN_SET_N_FCU_POS 8 +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_MASK GENMASK(17,16) +#define SDHCI_UHS2_TRAN_SET_RETRY_CNT_POS 16 + +#define SDHCI_UHS2_TRAN_SET_1_N_DAT_GAP_MASK GENMASK(7,0) + +#define SDHCI_UHS2_HOST_CAPS_PTR 0xE2 +#define SDHCI_UHS2_HOST_CAPS_GEN_OFFSET 0 +#define SDHCI_UHS2_HOST_CAPS_GEN_DAP_MASK GENMASK(3,0) +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_MASK GENMASK(7,4) +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP(gap) ((gap) * 360) +#define SDHCI_UHS2_HOST_CAPS_GEN_GAP_SHIFT 4 +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_MASK GENMASK(13,8) +#define SDHCI_UHS2_HOST_CAPS_GEN_LANE_SHIFT 8 +#define SDHCI_UHS2_HOST_CAPS_GEN_2L_HD_FD 1 +#define SDHCI_UHS2_HOST_CAPS_GEN_2D1U_FD 2 +#define SDHCI_UHS2_HOST_CAPS_GEN_1D2U_FD 4 +#define SDHCI_UHS2_HOST_CAPS_GEN_2D2U_FD 8 +#define SDHCI_UHS2_HOST_CAPS_GEN_ADDR_64 BIT(14) +#define SDHCI_UHS2_HOST_CAPS_GEN_BOOT BIT(15) +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_MASK GENMASK(17,16) +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_SHIFT 16 +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_RMV 0 +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB 1 +#define SDHCI_UHS2_HOST_CAPS_GEN_DEV_TYPE_EMB_RMV 2 +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_MASK GENMASK(21,18) +#define SDHCI_UHS2_HOST_CAPS_GEN_NUM_DEV_SHIFT 18 +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_MASK GENMASK(23,22) +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_SHIFT 22 +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_P2P 0 +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_RING 1 +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB 2 +#define SDHCI_UHS2_HOST_CAPS_GEN_BUS_TOPO_HUB_RING 3 + +#define SDHCI_UHS2_HOST_CAPS_PHY_OFFSET 4 +#define SDHCI_UHS2_HOST_CAPS_PHY_REV_MASK GENMASK(5,0) +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_MASK GENMASK(7,6) +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_SHIFT 6 +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_A 0 +#define SDHCI_UHS2_HOST_CAPS_PHY_RANGE_B 1 +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_MASK GENMASK(19,16) +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_SYN_SHIFT 16 +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_MASK GENMASK(23,20) +#define SDHCI_UHS2_HOST_CAPS_PHY_N_LSS_DIR_SHIFT 20 +#define SDHCI_UHS2_HOST_CAPS_TRAN_OFFSET 8 +#define SDHCI_UHS2_HOST_CAPS_TRAN_LINK_REV_MASK GENMASK(5,0) +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_MASK GENMASK(15,8) +#define SDHCI_UHS2_HOST_CAPS_TRAN_N_FCU_SHIFT 8 +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_MASK GENMASK(18,16) +#define SDHCI_UHS2_HOST_CAPS_TRAN_HOST_TYPE_SHIFT 16 +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_MASK GENMASK(31,20) +#define SDHCI_UHS2_HOST_CAPS_TRAN_BLK_LEN_SHIFT 20 + +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_OFFSET 12 +#define SDHCI_UHS2_HOST_CAPS_TRAN_1_N_DATA_GAP_MASK GENMASK(7,0) + +#define SDHCI_UHS2_TEST_PTR 0xE4 +#define SDHCI_UHS2_TEST_ERR_HEADER BIT(0) +#define SDHCI_UHS2_TEST_ERR_RES BIT(1) +#define SDHCI_UHS2_TEST_ERR_RETRY_EXP BIT(2) +#define SDHCI_UHS2_TEST_ERR_CRC BIT(3) +#define SDHCI_UHS2_TEST_ERR_FRAME BIT(4) +#define SDHCI_UHS2_TEST_ERR_TID BIT(5) +#define SDHCI_UHS2_TEST_ERR_UNRECOVER BIT(7) +#define SDHCI_UHS2_TEST_ERR_EBUSY BIT(8) +#define SDHCI_UHS2_TEST_ERR_ADMA BIT(15) +#define SDHCI_UHS2_TEST_ERR_RES_TIMEOUT BIT(16) +#define SDHCI_UHS2_TEST_ERR_DEADLOCK_TIMEOUT BIT(17) +#define SDHCI_UHS2_TEST_ERR_VENDOR BIT(27) + +#define SDHCI_UHS2_EMBED_CTRL 0xE6 +#define SDHCI_UHS2_VENDOR 0xE8 + +#endif /* __SDHCI_UHS2_H */ diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 0770c036e2ff..d9d7a76cedc1 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -43,8 +43,27 @@ #define SDHCI_TRNS_READ 0x10 #define SDHCI_TRNS_MULTI 0x20 +/* + * Defined in Host Version 4.10. + * 1 - R5 (SDIO) + * 0 - R1 (Memory) + */ +#define SDHCI_TRNS_RES_TYPE 0x40 +#define SDHCI_TRNS_RES_ERR_CHECK 0x80 +#define SDHCI_TRNS_RES_INT_DIS 0x0100 + #define SDHCI_COMMAND 0x0E #define SDHCI_CMD_RESP_MASK 0x03 + +/* + * Host Version 4.10 adds this bit to distinguish a main command or + * sub command. + * CMD53(SDIO) - main command + * CMD52(SDIO) - sub command which doesn't have data block or doesn't + * indicate busy. + */ +#define SDHCI_CMD_SUB_CMD 0x04 + #define SDHCI_CMD_CRC 0x08 #define SDHCI_CMD_INDEX 0x10 #define SDHCI_CMD_DATA 0x20 @@ -60,11 +79,19 @@ #define SDHCI_RESPONSE 0x10 +#define SDHCI_RESPONSE_CM_TRAN_ABORT_OFFSET 0x10 +#define SDHCI_RESPONSE_CM_TRAN_ABORT_SIZE 4 +#define SDHCI_RESPONSE_SD_TRAN_ABORT_OFFSET 0x18 +#define SDHCI_RESPONSE_SD_TRAN_ABORT_SIZE 8 + #define SDHCI_BUFFER 0x20 #define SDHCI_PRESENT_STATE 0x24 #define SDHCI_CMD_INHIBIT 0x00000001 #define SDHCI_DATA_INHIBIT 0x00000002 + +#define SDHCI_DATA_HIGH_LVL_MASK 0x000000F0 + #define SDHCI_DOING_WRITE 0x00000100 #define SDHCI_DOING_READ 0x00000200 #define SDHCI_SPACE_AVAILABLE 0x00000400 @@ -80,6 +107,13 @@ #define SDHCI_DATA_0_LVL_MASK 0x00100000 #define SDHCI_CMD_LVL 0x01000000 +#define SDHCI_HOST_REGULATOR_STABLE 0x02000000 +#define SDHCI_CMD_NOT_ISSUE_ERR 0x08000000 +#define SDHCI_SUB_CMD_STATUS 0x10000000 +#define SDHCI_UHS2_IN_DORMANT_STATE 0x20000000 +#define SDHCI_UHS2_LANE_SYNC 0x40000000 +#define SDHCI_UHS2_IF_DETECT 0x80000000 + #define SDHCI_HOST_CONTROL 0x28 #define SDHCI_CTRL_LED 0x01 #define SDHCI_CTRL_4BITBUS 0x02 @@ -100,6 +134,11 @@ #define SDHCI_POWER_300 0x0C #define SDHCI_POWER_330 0x0E +/* VDD2 - UHS2 */ +#define SDHCI_VDD2_POWER_ON 0x10 +#define SDHCI_VDD2_POWER_180 0xA0 +#define SDHCI_VDD2_POWER_120 0x80 + #define SDHCI_BLOCK_GAP_CONTROL 0x2A #define SDHCI_WAKE_UP_CONTROL 0x2B @@ -110,7 +149,7 @@ #define SDHCI_CLOCK_CONTROL 0x2C #define SDHCI_DIVIDER_SHIFT 8 #define SDHCI_DIVIDER_HI_SHIFT 6 -#define SDHCI_DIV_MASK 0xFF +#define SDHCI_DIV_MASK 0xFF #define SDHCI_DIV_MASK_LEN 8 #define SDHCI_DIV_HI_MASK 0x300 #define SDHCI_PROG_CLOCK_MODE 0x0020 @@ -139,6 +178,10 @@ #define SDHCI_INT_CARD_REMOVE 0x00000080 #define SDHCI_INT_CARD_INT 0x00000100 #define SDHCI_INT_RETUNE 0x00001000 + +/* Host Version 4.10 */ +#define SDHCI_INT_FX_EVENT 0x00002000 + #define SDHCI_INT_CQE 0x00004000 #define SDHCI_INT_ERROR 0x00008000 #define SDHCI_INT_TIMEOUT 0x00010000 @@ -152,6 +195,9 @@ #define SDHCI_INT_AUTO_CMD_ERR 0x01000000 #define SDHCI_INT_ADMA_ERROR 0x02000000 +/* Host Version 4.0 */ +#define SDHCI_INT_RESPONSE_ERROR 0x08000000 + #define SDHCI_INT_NORMAL_MASK 0x00007FFF #define SDHCI_INT_ERROR_MASK 0xFFFF8000 @@ -178,6 +224,9 @@ #define SDHCI_AUTO_CMD_END_BIT 0x00000008 #define SDHCI_AUTO_CMD_INDEX 0x00000010 +/* Host Version 4.10 */ +#define SDHCI_ACMD_RESPONSE_ERROR 0x0020 + #define SDHCI_HOST_CONTROL2 0x3E #define SDHCI_CTRL_UHS_MASK 0x0007 #define SDHCI_CTRL_UHS_SDR12 0x0000 @@ -186,6 +235,7 @@ #define SDHCI_CTRL_UHS_SDR104 0x0003 #define SDHCI_CTRL_UHS_DDR50 0x0004 #define SDHCI_CTRL_HS400 0x0005 /* Non-standard */ +#define SDHCI_CTRL_UHS_2 0x0007 /* UHS-2 */ #define SDHCI_CTRL_VDD_180 0x0008 #define SDHCI_CTRL_DRV_TYPE_MASK 0x0030 #define SDHCI_CTRL_DRV_TYPE_B 0x0000 @@ -194,9 +244,12 @@ #define SDHCI_CTRL_DRV_TYPE_D 0x0030 #define SDHCI_CTRL_EXEC_TUNING 0x0040 #define SDHCI_CTRL_TUNED_CLK 0x0080 +#define SDHCI_CTRL_UHS2_INTERFACE_EN 0x0100 /* UHS-2 */ +#define SDHCI_CTRL_ADMA2_LEN_MODE 0x0400 #define SDHCI_CMD23_ENABLE 0x0800 #define SDHCI_CTRL_V4_MODE 0x1000 #define SDHCI_CTRL_64BIT_ADDR 0x2000 +#define SDHCI_CTRL_ASYNC_INT_EN 0x4000 #define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000 #define SDHCI_CAPABILITIES 0x40 @@ -217,11 +270,13 @@ #define SDHCI_CAN_VDD_180 0x04000000 #define SDHCI_CAN_64BIT_V4 0x08000000 #define SDHCI_CAN_64BIT 0x10000000 +#define SDHCI_CAN_ASYNC_INT 0x20000000 #define SDHCI_CAPABILITIES_1 0x44 #define SDHCI_SUPPORT_SDR50 0x00000001 #define SDHCI_SUPPORT_SDR104 0x00000002 #define SDHCI_SUPPORT_DDR50 0x00000004 +#define SDHCI_SUPPORT_UHS2 0x00000008 /* UHS-2 support */ #define SDHCI_DRIVER_TYPE_A 0x00000010 #define SDHCI_DRIVER_TYPE_C 0x00000020 #define SDHCI_DRIVER_TYPE_D 0x00000040 @@ -230,19 +285,28 @@ #define SDHCI_RETUNING_MODE_MASK GENMASK(15, 14) #define SDHCI_CLOCK_MUL_MASK GENMASK(23, 16) #define SDHCI_CAN_DO_ADMA3 0x08000000 +#define SDHCI_SUPPORT_VDD2_180 0x10000000 /* UHS-2 1.8V VDD2 */ +#define SDHCI_RSVD_FOR_VDD2 0x20000000 /* Rsvd for future VDD2 */ #define SDHCI_SUPPORT_HS400 0x80000000 /* Non-standard */ #define SDHCI_MAX_CURRENT 0x48 +#define SDHCI_MAX_CURRENT_1 0x4C #define SDHCI_MAX_CURRENT_LIMIT GENMASK(7, 0) #define SDHCI_MAX_CURRENT_330_MASK GENMASK(7, 0) #define SDHCI_MAX_CURRENT_300_MASK GENMASK(15, 8) #define SDHCI_MAX_CURRENT_180_MASK GENMASK(23, 16) +#define SDHCI_MAX_CURRENT_VDD2_180_MASK GENMASK(7, 0) /* UHS2 */ #define SDHCI_MAX_CURRENT_MULTIPLIER 4 /* 4C-4F reserved for more max current */ #define SDHCI_SET_ACMD12_ERROR 0x50 +/* Host Version 4.10 */ +#define SDHCI_SET_ACMD_RESPONSE_ERROR 0x20 #define SDHCI_SET_INT_ERROR 0x52 +/* Host Version 4.10 */ +#define SDHCI_SET_INT_TUNING_ERROR 0x0400 +#define SDHCI_SET_INT_RESPONSE_ERROR 0x0800 #define SDHCI_ADMA_ERROR 0x54 @@ -259,10 +323,16 @@ #define SDHCI_PRESET_FOR_SDR104 0x6C #define SDHCI_PRESET_FOR_DDR50 0x6E #define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */ + +/* TODO: 0x74 is used for UHS2 in 4.10. How about HS400? */ +/* UHS2 */ +#define SDHCI_PRESET_FOR_UHS2 0x74 #define SDHCI_PRESET_DRV_MASK GENMASK(15, 14) #define SDHCI_PRESET_CLKGEN_SEL BIT(10) #define SDHCI_PRESET_SDCLK_FREQ_MASK GENMASK(9, 0) +#define SDHCI_ADMA3_ADDRESS 0x78 + #define SDHCI_SLOT_INT_STATUS 0xFC #define SDHCI_HOST_VERSION 0xFE @@ -652,6 +722,7 @@ struct sdhci_ops { void (*request_done)(struct sdhci_host *host, struct mmc_request *mrq); void (*dump_vendor_regs)(struct sdhci_host *host); + void (*dump_uhs2_regs)(struct sdhci_host *host); }; #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS