deleted file mode 100644
@@ -1,75 +0,0 @@
-* MTK MMC controller
-
-The MTK MSDC can act as a MMC controller
-to support MMC, SD, and SDIO types of memory cards.
-
-This file documents differences between the core properties in mmc.txt
-and the properties used by the msdc driver.
-
-Required properties:
-- compatible: value should be either of the following.
- "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
- "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
- "mediatek,mt8183-mmc": for mmc host ip compatible with mt8183
- "mediatek,mt8516-mmc": for mmc host ip compatible with mt8516
- "mediatek,mt6779-mmc": for mmc host ip compatible with mt6779
- "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
- "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
- "mediatek,mt7622-mmc": for MT7622 SoC
- "mediatek,mt7623-mmc", "mediatek,mt2701-mmc": for MT7623 SoC
- "mediatek,mt7620-mmc", for MT7621 SoC (and others)
-
-- reg: physical base address of the controller and length
-- interrupts: Should contain MSDC interrupt number
-- clocks: Should contain phandle for the clock feeding the MMC controller
-- clock-names: Should contain the following:
- "source" - source clock (required)
- "hclk" - HCLK which used for host (required)
- "source_cg" - independent source clock gate (required for MT2712)
- "bus_clk" - bus clock used for internal register access (required for MT2712 MSDC0/3)
-- pinctrl-names: should be "default", "state_uhs"
-- pinctrl-0: should contain default/high speed pin ctrl
-- pinctrl-1: should contain uhs mode pin ctrl
-- vmmc-supply: power to the Core
-- vqmmc-supply: power to the IO
-
-Optional properties:
-- assigned-clocks: PLL of the source clock
-- assigned-clock-parents: parent of source clock, used for HS400 mode to get 400Mhz source clock
-- hs400-ds-delay: HS400 DS delay setting
-- mediatek,hs200-cmd-int-delay: HS200 command internal delay setting.
- This field has total 32 stages.
- The value is an integer from 0 to 31.
-- mediatek,hs400-cmd-int-delay: HS400 command internal delay setting
- This field has total 32 stages.
- The value is an integer from 0 to 31.
-- mediatek,hs400-cmd-resp-sel-rising: HS400 command response sample selection
- If present,HS400 command responses are sampled on rising edges.
- If not present,HS400 command responses are sampled on falling edges.
-- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc
- error caused by stop clock(fifo full)
- Valid range = [0:0x7]. if not present, default value is 0.
- applied to compatible "mediatek,mt2701-mmc".
-- resets: Phandle and reset specifier pair to softreset line of MSDC IP.
-- reset-names: Should be "hrst".
-
-Examples:
-mmc0: mmc@11230000 {
- compatible = "mediatek,mt8173-mmc", "mediatek,mt8135-mmc";
- reg = <0 0x11230000 0 0x108>;
- interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>;
- vmmc-supply = <&mt6397_vemc_3v3_reg>;
- vqmmc-supply = <&mt6397_vio18_reg>;
- clocks = <&pericfg CLK_PERI_MSDC30_0>,
- <&topckgen CLK_TOP_MSDC50_0_H_SEL>;
- clock-names = "source", "hclk";
- pinctrl-names = "default", "state_uhs";
- pinctrl-0 = <&mmc0_pins_default>;
- pinctrl-1 = <&mmc0_pins_uhs>;
- assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
- assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
- hs400-ds-delay = <0x14015>;
- mediatek,hs200-cmd-int-delay = <26>;
- mediatek,hs400-cmd-int-delay = <14>;
- mediatek,hs400-cmd-resp-sel-rising;
-};
new file mode 100644
@@ -0,0 +1,165 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/mtk-sd.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MTK MSDC Storage Host Controller Binding
+
+maintainers:
+ - Chaotian Jing <chaotian.jing@mediatek.com>
+ - Wenbin Mei <wenbin.mei@mediatek.com>
+
+allOf:
+ - $ref: mmc-controller.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - mediatek,mt2701-mmc
+ - mediatek,mt2712-mmc
+ - mediatek,mt6779-mmc
+ - mediatek,mt7620-mmc
+ - mediatek,mt7622-mmc
+ - mediatek,mt8135-mmc
+ - mediatek,mt8173-mmc
+ - mediatek,mt8183-mmc
+ - mediatek,mt8516-mmc
+ - items:
+ - const: mediatek,mt7623-mmc
+ - const: mediatek,mt2701-mmc
+
+ clocks:
+ description:
+ Should contain phandle for the clock feeding the MMC controller.
+ minItems: 2
+ maxItems: 4
+ items:
+ - description: source clock (required).
+ - description: HCLK which used for host (required).
+ - description: independent source clock gate (required for MT2712).
+ - description: bus clock used for internal register access (required for MT2712 MSDC0/3).
+
+ clock-names:
+ minItems: 2
+ maxItems: 4
+ items:
+ - const: source
+ - const: hclk
+ - const: source_cg
+ - const: bus_clk
+
+ pinctrl-names:
+ items:
+ - const: default
+ - const: state_uhs
+
+ pinctrl-0:
+ description:
+ should contain default/high speed pin ctrl.
+ maxItems: 1
+
+ pinctrl-1:
+ description:
+ should contain uhs mode pin ctrl.
+ maxItems: 1
+
+ assigned-clocks:
+ description:
+ PLL of the source clock.
+ maxItems: 1
+
+ assigned-clock-parents:
+ description:
+ parent of source clock, used for HS400 mode to get 400Mhz source clock.
+ maxItems: 1
+
+ hs400-ds-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ HS400 DS delay setting.
+ minimum: 0
+ maximum: 0xffffffff
+
+ mediatek,hs200-cmd-int-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ HS200 command internal delay setting.
+ This field has total 32 stages.
+ The value is an integer from 0 to 31.
+ minimum: 0
+ maximum: 31
+
+ mediatek,hs400-cmd-int-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ HS400 command internal delay setting.
+ This field has total 32 stages.
+ The value is an integer from 0 to 31.
+ minimum: 0
+ maximum: 31
+
+ mediatek,hs400-cmd-resp-sel-rising:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ HS400 command response sample selection.
+ If present, HS400 command responses are sampled on rising edges.
+ If not present, HS400 command responses are sampled on falling edges.
+
+ mediatek,latch-ck:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Some SoCs do not support enhance_rx, need set correct latch-ck to avoid
+ data crc error caused by stop clock(fifo full) Valid range = [0:0x7].
+ if not present, default value is 0.
+ applied to compatible "mediatek,mt2701-mmc".
+ minimum: 0
+ maximum: 7
+
+ resets:
+ maxItems: 1
+
+ reset-names:
+ const: hrst
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - pinctrl-names
+ - pinctrl-0
+ - pinctrl-1
+ - vmmc-supply
+ - vqmmc-supply
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/mt8173-clk.h>
+ mmc0: mmc@11230000 {
+ compatible = "mediatek,mt8173-mmc";
+ reg = <0x11230000 0x1000>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>;
+ vmmc-supply = <&mt6397_vemc_3v3_reg>;
+ vqmmc-supply = <&mt6397_vio18_reg>;
+ clocks = <&pericfg CLK_PERI_MSDC30_0>,
+ <&topckgen CLK_TOP_MSDC50_0_H_SEL>;
+ clock-names = "source", "hclk";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_pins_default>;
+ pinctrl-1 = <&mmc0_pins_uhs>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
+ assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
+ hs400-ds-delay = <0x14015>;
+ mediatek,hs200-cmd-int-delay = <26>;
+ mediatek,hs400-cmd-int-delay = <14>;
+ mediatek,hs400-cmd-resp-sel-rising;
+ };
+
+...