@@ -14376,6 +14376,14 @@ W: https://linuxtv.org
T: git git://linuxtv.org/media_tree.git
F: drivers/media/dvb-frontends/stv6111*
+MEDIA DRIVERS FOR STM32 - CSI
+M: Alain Volmat <alain.volmat@foss.st.com>
+L: linux-media@vger.kernel.org
+S: Supported
+T: git git://linuxtv.org/media_tree.git
+F: Documentation/devicetree/bindings/media/st,stm32mp25-csi.yaml
+F: drivers/media/platform/stm32/stm32-csi.c
+
MEDIA DRIVERS FOR STM32 - DCMI / DCMIPP
M: Hugues Fruchet <hugues.fruchet@foss.st.com>
M: Alain Volmat <alain.volmat@foss.st.com>
@@ -1,6 +1,20 @@
# SPDX-License-Identifier: GPL-2.0-only
# V4L drivers
+config VIDEO_STM32_CSI
+ tristate "STM32 Camera Serial Interface (CSI) support"
+ depends on V4L_PLATFORM_DRIVERS
+ depends on VIDEO_DEV && OF
+ depends on ARCH_STM32 || COMPILE_TEST
+ select MEDIA_CONTROLLER
+ select V4L2_FWNODE
+ help
+ This module makes the STM32 Camera Serial Interface (CSI)
+ available as a v4l2 device.
+
+ To compile this driver as a module, choose M here: the module
+ will be called stm32-csi.
+
config VIDEO_STM32_DCMI
tristate "STM32 Digital Camera Memory Interface (DCMI) support"
depends on V4L_PLATFORM_DRIVERS
@@ -1,4 +1,5 @@
# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_VIDEO_STM32_CSI) += stm32-csi.o
obj-$(CONFIG_VIDEO_STM32_DCMI) += stm32-dcmi.o
obj-$(CONFIG_VIDEO_STM32_DCMIPP) += stm32-dcmipp/
stm32-dma2d-objs := dma2d/dma2d.o dma2d/dma2d-hw.o
new file mode 100644
@@ -0,0 +1,1137 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for STM32 Camera Serial Interface
+ *
+ * Copyright (C) STMicroelectronics SA 2024
+ * Author: Alain Volmat <alain.volmat@foss.st.com>
+ * for STMicroelectronics.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#include <media/mipi-csi2.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-subdev.h>
+
+#define STM32_CSI_CR 0x0000
+#define STM32_CSI_CR_CSIEN BIT(0)
+#define STM32_CSI_CR_VCXSTART(x) BIT(2 + ((x) * 4))
+#define STM32_CSI_CR_VCXSTOP(x) BIT(3 + ((x) * 4))
+#define STM32_CSI_PCR 0x0004
+#define STM32_CSI_PCR_DL1EN BIT(3)
+#define STM32_CSI_PCR_DL0EN BIT(2)
+#define STM32_CSI_PCR_CLEN BIT(1)
+#define STM32_CSI_PCR_PWRDOWN BIT(0)
+#define STM32_CSI_VCXCFGR1(x) ((((x) + 1) * 0x0010) + 0x0)
+#define STM32_CSI_VCXCFGR1_ALLDT BIT(0)
+#define STM32_CSI_VCXCFGR1_DT0EN BIT(1)
+#define STM32_CSI_VCXCFGR1_DT1EN BIT(2)
+#define STM32_CSI_VCXCFGR1_CDTFT_SHIFT 8
+#define STM32_CSI_VCXCFGR1_DT0_SHIFT 16
+#define STM32_CSI_VCXCFGR1_DT0FT_SHIFT 24
+#define STM32_CSI_VCXCFGR2(x) ((((x) + 1) * 0x0010) + 0x4)
+#define STM32_CSI_VCXCFGR2_DT1_SHIFT 0
+#define STM32_CSI_VCXCFGR2_DT1FT_SHIFT 8
+#define STM32_CSI_INPUT_BPP8 2
+#define STM32_CSI_INPUT_BPP10 3
+#define STM32_CSI_INPUT_BPP12 4
+#define STM32_CSI_INPUT_BPP14 5
+#define STM32_CSI_LMCFGR 0x0070
+#define STM32_CSI_LMCFGR_LANENB_SHIFT 8
+#define STM32_CSI_LMCFGR_DLMAP_SHIFT 16
+#define STM32_CSI_IER0 0x0080
+#define STM32_CSI_IER1 0x0084
+#define STM32_CSI_SR0 0x0090
+#define STM32_CSI_SR0_SYNCERRF BIT(30)
+#define STM32_CSI_SR0_SPKTERRF BIT(28)
+#define STM32_CSI_SR0_IDERRF BIT(27)
+#define STM32_CSI_SR0_CECCERRF BIT(26)
+#define STM32_CSI_SR0_ECCERRF BIT(25)
+#define STM32_CSI_SR0_CRCERRF BIT(24)
+#define STM32_CSI_SR0_CCFIFOFF BIT(21)
+#define STM32_CSI_SR0_VCXSTATEF(x) BIT(17 + (x))
+#define STM32_CSI_SR1 0x0094
+#define STM32_CSI_SR1_ECTRLDL1F BIT(12)
+#define STM32_CSI_SR1_ESYNCESCDL1F BIT(11)
+#define STM32_CSI_SR1_EESCDL1F BIT(10)
+#define STM32_CSI_SR1_ESOTSYNCDL1F BIT(9)
+#define STM32_CSI_SR1_ESOTDL1F BIT(8)
+#define STM32_CSI_SR1_ECTRLDL0F BIT(4)
+#define STM32_CSI_SR1_ESYNCESCDL0F BIT(3)
+#define STM32_CSI_SR1_EESCDL0F BIT(2)
+#define STM32_CSI_SR1_ESOTSYNCDL0F BIT(1)
+#define STM32_CSI_SR1_ESOTDL0F BIT(0)
+#define STM32_CSI_FCR0 0x0100
+#define STM32_CSI_FCR1 0x0104
+#define STM32_CSI_SPDFR 0x0110
+#define STM32_CSI_DT_MASK 0x3f
+#define STM32_CSI_VC_MASK 0x03
+#define STM32_CSI_ERR1 0x0114
+#define STM32_CSI_ERR1_IDVCERR_SHIFT 22
+#define STM32_CSI_ERR1_IDDTERR_SHIFT 16
+#define STM32_CSI_ERR1_CECCVCERR_SHIFT 14
+#define STM32_CSI_ERR1_CECCDTERR_SHIFT 8
+#define STM32_CSI_ERR1_CRCVCERR_SHIFT 6
+#define STM32_CSI_ERR1_CRCDTERR_SHIFT 0
+#define STM32_CSI_ERR2 0x0118
+#define STM32_CSI_ERR2_SYNCVCERR_SHIFT 18
+#define STM32_CSI_ERR2_SPKTVCERR_SHIFT 6
+#define STM32_CSI_ERR2_SPKTDTERR_SHIFT 0
+#define STM32_CSI_PRCR 0x1000
+#define STM32_CSI_PRCR_PEN BIT(1)
+#define STM32_CSI_PMCR 0x1004
+#define STM32_CSI_PFCR 0x1008
+#define STM32_CSI_PFCR_CCFR_MASK GENMASK(5, 0)
+#define STM32_CSI_PFCR_CCFR_SHIFT 0
+#define STM32_CSI_PFCR_HSFR_MASK GENMASK(14, 8)
+#define STM32_CSI_PFCR_HSFR_SHIFT 8
+#define STM32_CSI_PFCR_DLD BIT(16)
+#define STM32_CSI_PTCR0 0x1010
+#define STM32_CSI_PTCR0_TCKEN BIT(0)
+#define STM32_CSI_PTCR1 0x1014
+#define STM32_CSI_PTCR1_TWM BIT(16)
+#define STM32_CSI_PTCR1_TDI_MASK GENMASK(7, 0)
+#define STM32_CSI_PTCR1_TDI_SHIFT 0
+#define STM32_CSI_PTSR 0x1018
+
+#define STM32_CSI_LANES_MAX 2
+
+#define STM32_CSI_SR0_ERRORS (STM32_CSI_SR0_SYNCERRF | STM32_CSI_SR0_SPKTERRF |\
+ STM32_CSI_SR0_IDERRF | STM32_CSI_SR0_CECCERRF |\
+ STM32_CSI_SR0_ECCERRF | STM32_CSI_SR0_CRCERRF |\
+ STM32_CSI_SR0_CCFIFOFF)
+#define STM32_CSI_SR1_DL0_ERRORS (STM32_CSI_SR1_ECTRLDL0F | STM32_CSI_SR1_ESYNCESCDL0F |\
+ STM32_CSI_SR1_EESCDL0F | STM32_CSI_SR1_ESOTSYNCDL0F |\
+ STM32_CSI_SR1_ESOTDL0F)
+#define STM32_CSI_SR1_DL1_ERRORS (STM32_CSI_SR1_ECTRLDL1F | STM32_CSI_SR1_ESYNCESCDL1F |\
+ STM32_CSI_SR1_EESCDL1F | STM32_CSI_SR1_ESOTSYNCDL1F |\
+ STM32_CSI_SR1_ESOTDL1F)
+#define STM32_CSI_SR1_ERRORS (STM32_CSI_SR1_DL0_ERRORS | STM32_CSI_SR1_DL1_ERRORS)
+
+enum stm32_csi_pads {
+ STM32_CSI_PAD_SINK,
+ STM32_CSI_PAD_SOURCE,
+ STM32_CSI_PAD_MAX,
+};
+
+struct stm32_csi_event {
+ u32 mask;
+ const char * const name;
+};
+
+static const struct stm32_csi_event stm32_csi_events_sr0[] = {
+ {STM32_CSI_SR0_SYNCERRF, "Synchronization error"},
+ {STM32_CSI_SR0_SPKTERRF, "Short packet error"},
+ {STM32_CSI_SR0_IDERRF, "Data type ID error"},
+ {STM32_CSI_SR0_CECCERRF, "Corrected ECC error"},
+ {STM32_CSI_SR0_ECCERRF, "ECC error"},
+ {STM32_CSI_SR0_CRCERRF, "CRC error"},
+ {STM32_CSI_SR0_CCFIFOFF, "Clk changer FIFO full error"},
+};
+
+#define STM32_CSI_NUM_SR0_EVENTS ARRAY_SIZE(stm32_csi_events_sr0)
+
+static const struct stm32_csi_event stm32_csi_events_sr1[] = {
+ {STM32_CSI_SR1_ECTRLDL1F, "L1: D-PHY control error"},
+ {STM32_CSI_SR1_ESYNCESCDL1F,
+ "L1: D-PHY low power data transmission synchro error"},
+ {STM32_CSI_SR1_EESCDL1F, "L1: D-PHY escape entry error"},
+ {STM32_CSI_SR1_ESOTSYNCDL1F,
+ "L1: Start of transmission synchro error"},
+ {STM32_CSI_SR1_ESOTDL1F, "L1: Start of transmission error"},
+ {STM32_CSI_SR1_ECTRLDL0F, "L0: D-PHY control error"},
+ {STM32_CSI_SR1_ESYNCESCDL0F,
+ "L0: D-PHY low power data transmission synchro error"},
+ {STM32_CSI_SR1_EESCDL0F, "L0: D-PHY escape entry error"},
+ {STM32_CSI_SR1_ESOTSYNCDL0F,
+ "L0: Start of transmission synchro error"},
+ {STM32_CSI_SR1_ESOTDL0F, "L0: Start of transmission error"},
+};
+
+#define STM32_CSI_NUM_SR1_EVENTS ARRAY_SIZE(stm32_csi_events_sr1)
+
+enum stm32_csi_clk {
+ STM32_CSI_CLK_PCLK,
+ STM32_CSI_CLK_TXESC,
+ STM32_CSI_CLK_CSI2PHY,
+ STM32_CSI_CLK_NB,
+};
+
+static const char * const stm32_csi_clks_id[] = {
+ "pclk",
+ "txesc",
+ "csi2phy",
+};
+
+struct stm32_csi_dev {
+ struct device *dev;
+
+ void __iomem *base;
+
+ struct clk_bulk_data clks[STM32_CSI_CLK_NB];
+ struct regulator_bulk_data supplies[2];
+
+ u8 lanes[STM32_CSI_LANES_MAX];
+ u8 num_lanes;
+
+ /*
+ * spinlock slock is used to protect to srX_counters tables being
+ * accessed from log_status and interrupt context
+ */
+ spinlock_t slock;
+
+ u32 sr0_counters[STM32_CSI_NUM_SR0_EVENTS];
+ u32 sr1_counters[STM32_CSI_NUM_SR1_EVENTS];
+
+ struct v4l2_subdev sd;
+ struct v4l2_async_notifier notifier;
+ struct media_pad pads[STM32_CSI_PAD_MAX];
+
+ /* Remote source */
+ struct v4l2_subdev *s_subdev;
+ u32 s_subdev_pad_nb;
+};
+
+struct stm32_csi_fmts {
+ u32 code;
+ u32 datatype;
+ u32 input_fmt;
+ u8 bpp;
+};
+
+#define FMT_MBUS_DT_DTFMT_BPP(mbus, dt, input, byteperpixel) \
+ { \
+ .code = MEDIA_BUS_FMT_##mbus, \
+ .datatype = MIPI_CSI2_DT_##dt, \
+ .input_fmt = STM32_CSI_INPUT_##input, \
+ .bpp = byteperpixel, \
+ }
+static const struct stm32_csi_fmts stm32_csi_formats[] = {
+ /* YUV 422 8 bit */
+ FMT_MBUS_DT_DTFMT_BPP(UYVY8_1X16, YUV422_8B, BPP8, 8),
+ FMT_MBUS_DT_DTFMT_BPP(YUYV8_1X16, YUV422_8B, BPP8, 8),
+ FMT_MBUS_DT_DTFMT_BPP(YVYU8_1X16, YUV422_8B, BPP8, 8),
+ FMT_MBUS_DT_DTFMT_BPP(VYUY8_1X16, YUV422_8B, BPP8, 8),
+
+ /* Raw Bayer */
+ /* 8 bit */
+ FMT_MBUS_DT_DTFMT_BPP(SBGGR8_1X8, RAW8, BPP8, 8),
+ FMT_MBUS_DT_DTFMT_BPP(SGBRG8_1X8, RAW8, BPP8, 8),
+ FMT_MBUS_DT_DTFMT_BPP(SGRBG8_1X8, RAW8, BPP8, 8),
+ FMT_MBUS_DT_DTFMT_BPP(SRGGB8_1X8, RAW8, BPP8, 8),
+ /* 10 bit */
+ FMT_MBUS_DT_DTFMT_BPP(SRGGB10_1X10, RAW10, BPP10, 10),
+ FMT_MBUS_DT_DTFMT_BPP(SGBRG10_1X10, RAW10, BPP10, 10),
+ FMT_MBUS_DT_DTFMT_BPP(SGRBG10_1X10, RAW10, BPP10, 10),
+ FMT_MBUS_DT_DTFMT_BPP(SRGGB10_1X10, RAW10, BPP10, 10),
+ /* 12 bit */
+ FMT_MBUS_DT_DTFMT_BPP(SRGGB12_1X12, RAW12, BPP12, 12),
+ FMT_MBUS_DT_DTFMT_BPP(SGBRG12_1X12, RAW12, BPP12, 12),
+ FMT_MBUS_DT_DTFMT_BPP(SGRBG12_1X12, RAW12, BPP12, 12),
+ FMT_MBUS_DT_DTFMT_BPP(SRGGB12_1X12, RAW12, BPP12, 12),
+ /* 14 bit */
+ FMT_MBUS_DT_DTFMT_BPP(SRGGB14_1X14, RAW14, BPP14, 14),
+ FMT_MBUS_DT_DTFMT_BPP(SGBRG14_1X14, RAW14, BPP14, 14),
+ FMT_MBUS_DT_DTFMT_BPP(SGRBG14_1X14, RAW14, BPP14, 14),
+ FMT_MBUS_DT_DTFMT_BPP(SRGGB14_1X14, RAW14, BPP14, 14),
+
+ /* RGB 565 */
+ FMT_MBUS_DT_DTFMT_BPP(RGB565_1X16, RGB565, BPP8, 8),
+
+ /* JPEG (datatype isn't used) */
+ FMT_MBUS_DT_DTFMT_BPP(JPEG_1X8, NULL, BPP8, 8),
+};
+
+struct stm32_csi_mbps_phy_reg {
+ unsigned int mbps;
+ unsigned int hsfreqrange;
+ unsigned int osc_freq_target;
+};
+
+/*
+ * Table describing configuration of the PHY depending on the
+ * intended Bit Rate. From table 5-8 Frequency Ranges and Defaults
+ * of the Synopsis DWC MIPI PHY databook
+ */
+static const struct stm32_csi_mbps_phy_reg snps_stm32mp25[] = {
+ { .mbps = 80, .hsfreqrange = 0x00, .osc_freq_target = 460 },
+ { .mbps = 90, .hsfreqrange = 0x10, .osc_freq_target = 460 },
+ { .mbps = 100, .hsfreqrange = 0x20, .osc_freq_target = 460 },
+ { .mbps = 110, .hsfreqrange = 0x30, .osc_freq_target = 460 },
+ { .mbps = 120, .hsfreqrange = 0x01, .osc_freq_target = 460 },
+ { .mbps = 130, .hsfreqrange = 0x11, .osc_freq_target = 460 },
+ { .mbps = 140, .hsfreqrange = 0x21, .osc_freq_target = 460 },
+ { .mbps = 150, .hsfreqrange = 0x31, .osc_freq_target = 460 },
+ { .mbps = 160, .hsfreqrange = 0x02, .osc_freq_target = 460 },
+ { .mbps = 170, .hsfreqrange = 0x12, .osc_freq_target = 460 },
+ { .mbps = 180, .hsfreqrange = 0x22, .osc_freq_target = 460 },
+ { .mbps = 190, .hsfreqrange = 0x32, .osc_freq_target = 460 },
+ { .mbps = 205, .hsfreqrange = 0x03, .osc_freq_target = 460 },
+ { .mbps = 220, .hsfreqrange = 0x13, .osc_freq_target = 460 },
+ { .mbps = 235, .hsfreqrange = 0x23, .osc_freq_target = 460 },
+ { .mbps = 250, .hsfreqrange = 0x33, .osc_freq_target = 460 },
+ { .mbps = 275, .hsfreqrange = 0x04, .osc_freq_target = 460 },
+ { .mbps = 300, .hsfreqrange = 0x14, .osc_freq_target = 460 },
+ { .mbps = 325, .hsfreqrange = 0x25, .osc_freq_target = 460 },
+ { .mbps = 350, .hsfreqrange = 0x35, .osc_freq_target = 460 },
+ { .mbps = 400, .hsfreqrange = 0x05, .osc_freq_target = 460 },
+ { .mbps = 450, .hsfreqrange = 0x16, .osc_freq_target = 460 },
+ { .mbps = 500, .hsfreqrange = 0x26, .osc_freq_target = 460 },
+ { .mbps = 550, .hsfreqrange = 0x37, .osc_freq_target = 460 },
+ { .mbps = 600, .hsfreqrange = 0x07, .osc_freq_target = 460 },
+ { .mbps = 650, .hsfreqrange = 0x18, .osc_freq_target = 460 },
+ { .mbps = 700, .hsfreqrange = 0x28, .osc_freq_target = 460 },
+ { .mbps = 750, .hsfreqrange = 0x39, .osc_freq_target = 460 },
+ { .mbps = 800, .hsfreqrange = 0x09, .osc_freq_target = 460 },
+ { .mbps = 850, .hsfreqrange = 0x19, .osc_freq_target = 460 },
+ { .mbps = 900, .hsfreqrange = 0x29, .osc_freq_target = 460 },
+ { .mbps = 950, .hsfreqrange = 0x3a, .osc_freq_target = 460 },
+ { .mbps = 1000, .hsfreqrange = 0x0a, .osc_freq_target = 460 },
+ { .mbps = 1050, .hsfreqrange = 0x1a, .osc_freq_target = 460 },
+ { .mbps = 1100, .hsfreqrange = 0x2a, .osc_freq_target = 460 },
+ { .mbps = 1150, .hsfreqrange = 0x3b, .osc_freq_target = 460 },
+ { .mbps = 1200, .hsfreqrange = 0x0b, .osc_freq_target = 460 },
+ { .mbps = 1250, .hsfreqrange = 0x1b, .osc_freq_target = 460 },
+ { .mbps = 1300, .hsfreqrange = 0x2b, .osc_freq_target = 460 },
+ { .mbps = 1350, .hsfreqrange = 0x3c, .osc_freq_target = 460 },
+ { .mbps = 1400, .hsfreqrange = 0x0c, .osc_freq_target = 460 },
+ { .mbps = 1450, .hsfreqrange = 0x1c, .osc_freq_target = 460 },
+ { .mbps = 1500, .hsfreqrange = 0x2c, .osc_freq_target = 460 },
+ { .mbps = 1550, .hsfreqrange = 0x3d, .osc_freq_target = 285 },
+ { .mbps = 1600, .hsfreqrange = 0x0d, .osc_freq_target = 295 },
+ { .mbps = 1650, .hsfreqrange = 0x1d, .osc_freq_target = 304 },
+ { .mbps = 1700, .hsfreqrange = 0x2e, .osc_freq_target = 313 },
+ { .mbps = 1750, .hsfreqrange = 0x3e, .osc_freq_target = 322 },
+ { .mbps = 1800, .hsfreqrange = 0x0e, .osc_freq_target = 331 },
+ { .mbps = 1850, .hsfreqrange = 0x1e, .osc_freq_target = 341 },
+ { .mbps = 1900, .hsfreqrange = 0x2f, .osc_freq_target = 350 },
+ { .mbps = 1950, .hsfreqrange = 0x3f, .osc_freq_target = 359 },
+ { .mbps = 2000, .hsfreqrange = 0x0f, .osc_freq_target = 368 },
+ { .mbps = 2050, .hsfreqrange = 0x40, .osc_freq_target = 377 },
+ { .mbps = 2100, .hsfreqrange = 0x41, .osc_freq_target = 387 },
+ { .mbps = 2150, .hsfreqrange = 0x42, .osc_freq_target = 396 },
+ { .mbps = 2200, .hsfreqrange = 0x43, .osc_freq_target = 405 },
+ { .mbps = 2250, .hsfreqrange = 0x44, .osc_freq_target = 414 },
+ { .mbps = 2300, .hsfreqrange = 0x45, .osc_freq_target = 423 },
+ { .mbps = 2350, .hsfreqrange = 0x46, .osc_freq_target = 432 },
+ { .mbps = 2400, .hsfreqrange = 0x47, .osc_freq_target = 442 },
+ { .mbps = 2450, .hsfreqrange = 0x48, .osc_freq_target = 451 },
+ { .mbps = 2500, .hsfreqrange = 0x49, .osc_freq_target = 460 },
+ { /* sentinel */ }
+};
+
+static const struct v4l2_mbus_framefmt fmt_default = {
+ .width = 640,
+ .height = 480,
+ .code = MEDIA_BUS_FMT_RGB565_1X16,
+ .field = V4L2_FIELD_NONE,
+ .colorspace = V4L2_COLORSPACE_REC709,
+ .ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT,
+ .quantization = V4L2_QUANTIZATION_DEFAULT,
+ .xfer_func = V4L2_XFER_FUNC_DEFAULT,
+};
+
+static const struct stm32_csi_fmts *stm32_csi_code_to_fmt(unsigned int code)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(stm32_csi_formats); i++)
+ if (stm32_csi_formats[i].code == code)
+ return &stm32_csi_formats[i];
+
+ return NULL;
+}
+
+static inline struct stm32_csi_dev *to_csidev(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct stm32_csi_dev, sd);
+}
+
+static int stm32_csi_setup_lane_merger(struct stm32_csi_dev *csidev)
+{
+ u32 lmcfgr = 0;
+ int i;
+
+ for (i = 0; i < csidev->num_lanes; i++) {
+ if (!csidev->lanes[i] || csidev->lanes[i] > STM32_CSI_LANES_MAX) {
+ dev_err(csidev->dev, "Invalid lane id (%d)\n", csidev->lanes[i]);
+ return -EINVAL;
+ }
+ lmcfgr |= (csidev->lanes[i] << ((i * 4) + STM32_CSI_LMCFGR_DLMAP_SHIFT));
+ }
+
+ lmcfgr |= (csidev->num_lanes << STM32_CSI_LMCFGR_LANENB_SHIFT);
+
+ writel_relaxed(lmcfgr, csidev->base + STM32_CSI_LMCFGR);
+
+ return 0;
+}
+
+static void stm32_csi_phy_reg_write(struct stm32_csi_dev *csidev,
+ u32 addr, u32 val)
+{
+ /* Based on sequence described at section 5.2.3.2 of DesignWave document */
+ /* For writing the 4-bit testcode MSBs */
+ /* Set testen to high */
+ writel_relaxed(STM32_CSI_PTCR1_TWM, csidev->base + STM32_CSI_PTCR1);
+
+ /* Set testclk to high */
+ writel_relaxed(STM32_CSI_PTCR0_TCKEN, csidev->base + STM32_CSI_PTCR0);
+
+ /* Place 0x00 in testdin */
+ writel_relaxed(STM32_CSI_PTCR1_TWM, csidev->base + STM32_CSI_PTCR1);
+
+ /*
+ * Set testclk to low (with the falling edge on testclk, the testdin
+ * signal content is latched internally)
+ */
+ writel_relaxed(0, csidev->base + STM32_CSI_PTCR0);
+
+ /* Set testen to low */
+ writel_relaxed(0, csidev->base + STM32_CSI_PTCR1);
+
+ /* Place the 8-bit word corresponding to the testcode MSBs in testdin */
+ writel_relaxed(((addr >> 8) & STM32_CSI_PTCR1_TDI_MASK) << STM32_CSI_PTCR1_TDI_SHIFT,
+ csidev->base + STM32_CSI_PTCR1);
+
+ /* Set testclk to high */
+ writel_relaxed(STM32_CSI_PTCR0_TCKEN, csidev->base + STM32_CSI_PTCR0);
+
+ /* For writing the 8-bit testcode LSBs */
+ /* Set testclk to low */
+ writel_relaxed(0, csidev->base + STM32_CSI_PTCR0);
+
+ /* Set testen to high */
+ writel_relaxed(STM32_CSI_PTCR1_TWM, csidev->base + STM32_CSI_PTCR1);
+
+ /* Set testclk to high */
+ writel_relaxed(STM32_CSI_PTCR0_TCKEN, csidev->base + STM32_CSI_PTCR0);
+
+ /* Place the 8-bit word test data in testdin */
+ writel_relaxed((addr & STM32_CSI_PTCR1_TDI_MASK) <<
+ STM32_CSI_PTCR1_TDI_SHIFT | STM32_CSI_PTCR1_TWM,
+ csidev->base + STM32_CSI_PTCR1);
+
+ /*
+ * Set testclk to low (with the falling edge on testclk, the testdin
+ * signal content is latched internally)
+ */
+ writel_relaxed(0, csidev->base + STM32_CSI_PTCR0);
+
+ /* Set testen to low */
+ writel_relaxed(0, csidev->base + STM32_CSI_PTCR1);
+
+ /* For writing the data */
+ /* Place the 8-bit word corresponding to the page offset in testdin */
+ writel_relaxed((val & STM32_CSI_PTCR1_TDI_MASK) << STM32_CSI_PTCR1_TDI_SHIFT,
+ csidev->base + STM32_CSI_PTCR1);
+
+ /* Set testclk to high (test data is programmed internally */
+ writel_relaxed(STM32_CSI_PTCR0_TCKEN, csidev->base + STM32_CSI_PTCR0);
+
+ /* Finish by setting testclk to low */
+ writel_relaxed(0, csidev->base + STM32_CSI_PTCR0);
+}
+
+static int stm32_csi_start(struct stm32_csi_dev *csidev,
+ struct v4l2_subdev_state *state)
+{
+ const struct stm32_csi_mbps_phy_reg *phy_regs;
+ struct v4l2_mbus_framefmt *sink_fmt;
+ const struct stm32_csi_fmts *fmt;
+ unsigned long phy_clk_frate;
+ unsigned int mbps;
+ u32 lanes_ie = 0;
+ u32 lanes_en = 0;
+ s64 link_freq;
+ int ret;
+ u32 ccfr;
+
+ dev_dbg(csidev->dev, "Starting the CSI2\n");
+
+ /* Get the bpp value on pad0 (input of CSI) */
+ sink_fmt = v4l2_subdev_state_get_format(state, STM32_CSI_PAD_SINK);
+ fmt = stm32_csi_code_to_fmt(sink_fmt->code);
+
+ /* Get the remote sensor link frequency */
+ if (!csidev->s_subdev)
+ return -EIO;
+
+ link_freq = v4l2_get_link_freq(csidev->s_subdev->ctrl_handler,
+ fmt->bpp, 2 * csidev->num_lanes);
+ if (link_freq < 0)
+ return link_freq;
+
+ /* MBPS is expressed in Mbps, hence link_freq / 100000 * 2 */
+ mbps = div_s64(link_freq, 500000);
+ dev_dbg(csidev->dev, "Computed Mbps: %u\n", mbps);
+
+ for (phy_regs = snps_stm32mp25; phy_regs->mbps != 0; phy_regs++)
+ if (phy_regs->mbps >= mbps)
+ break;
+
+ if (!phy_regs->mbps) {
+ dev_err(csidev->dev, "Unsupported PHY speed (%u Mbps)", mbps);
+ return -ERANGE;
+ }
+
+ dev_dbg(csidev->dev, "PHY settings: (%u Mbps, %u HS FRange, %u OSC Freq)\n",
+ phy_regs->mbps, phy_regs->hsfreqrange,
+ phy_regs->osc_freq_target);
+
+ /* Prepare lanes related configuration bits */
+ lanes_ie |= STM32_CSI_SR1_DL0_ERRORS;
+ lanes_en |= STM32_CSI_PCR_DL0EN;
+ if (csidev->num_lanes == 2) {
+ lanes_ie |= STM32_CSI_SR1_DL1_ERRORS;
+ lanes_en |= STM32_CSI_PCR_DL1EN;
+ }
+
+ ret = pm_runtime_get_sync(csidev->dev);
+ if (ret < 0)
+ return ret;
+
+ /* Retrieve CSI2PHY clock rate to compute CCFR value */
+ phy_clk_frate = clk_get_rate(csidev->clks[STM32_CSI_CLK_CSI2PHY].clk);
+ if (!phy_clk_frate) {
+ pm_runtime_put(csidev->dev);
+ dev_err(csidev->dev, "CSI2PHY clock rate invalid (0)\n");
+ return ret;
+ }
+
+ ret = stm32_csi_setup_lane_merger(csidev);
+ if (ret) {
+ pm_runtime_put(csidev->dev);
+ return ret;
+ }
+
+ /* Enable the CSI */
+ writel_relaxed(STM32_CSI_CR_CSIEN, csidev->base + STM32_CSI_CR);
+
+ /* Enable some global CSI related interrupts - bits are same as SR0 */
+ writel_relaxed(STM32_CSI_SR0_ERRORS, csidev->base + STM32_CSI_IER0);
+
+ /* Enable lanes related error interrupts */
+ writel_relaxed(lanes_ie, csidev->base + STM32_CSI_IER1);
+
+ /* Initialization of the D-PHY */
+ /* Stop the D-PHY */
+ writel_relaxed(0, csidev->base + STM32_CSI_PRCR);
+
+ /* Keep the D-PHY in power down state */
+ writel_relaxed(0, csidev->base + STM32_CSI_PCR);
+
+ /* Enable testclr clock during 15ns */
+ writel_relaxed(STM32_CSI_PTCR0_TCKEN, csidev->base + STM32_CSI_PTCR0);
+ udelay(1);
+ writel_relaxed(0, csidev->base + STM32_CSI_PTCR0);
+
+ /* Set hsfreqrange */
+ phy_clk_frate /= 1000000;
+ ccfr = (phy_clk_frate - 17) * 4;
+ writel_relaxed((ccfr << STM32_CSI_PFCR_CCFR_SHIFT) |
+ (phy_regs->hsfreqrange << STM32_CSI_PFCR_HSFR_SHIFT),
+ csidev->base + STM32_CSI_PFCR);
+
+ /* set reg @08 deskew_polarity_rw 1'b1 */
+ stm32_csi_phy_reg_write(csidev, 0x08, 0x38);
+
+ /* set reg @0xE4 counter_for_des_en_config_if_rx 0x10 + DLL prog EN */
+ /* This is because 13<= cfgclkfreqrange[5:0]<=38 */
+ stm32_csi_phy_reg_write(csidev, 0xe4, 0x11);
+
+ /* set reg @0xe2 & reg @0xe3 value DLL target oscilation freq */
+ /* Based on the table page 77, osc_freq_target */
+ stm32_csi_phy_reg_write(csidev, 0xe2, phy_regs->osc_freq_target & 0xFF);
+ stm32_csi_phy_reg_write(csidev, 0xe3, (phy_regs->osc_freq_target >> 8) & 0x0F);
+
+ writel_relaxed(STM32_CSI_PFCR_DLD | readl_relaxed(csidev->base + STM32_CSI_PFCR),
+ csidev->base + STM32_CSI_PFCR);
+
+ /* Enable Lanes */
+ writel_relaxed(lanes_en | STM32_CSI_PCR_CLEN, csidev->base + STM32_CSI_PCR);
+ writel_relaxed(lanes_en | STM32_CSI_PCR_CLEN | STM32_CSI_PCR_PWRDOWN,
+ csidev->base + STM32_CSI_PCR);
+
+ writel_relaxed(STM32_CSI_PRCR_PEN, csidev->base + STM32_CSI_PRCR);
+
+ /* Remove the force */
+ writel_relaxed(0, csidev->base + STM32_CSI_PMCR);
+
+ return ret;
+}
+
+static void stm32_csi_stop(struct stm32_csi_dev *csidev)
+{
+ dev_dbg(csidev->dev, "Stopping the CSI2\n");
+
+ /* Disable the D-PHY */
+ writel_relaxed(0, csidev->base + STM32_CSI_PCR);
+
+ /* Disable ITs */
+ writel_relaxed(0, csidev->base + STM32_CSI_IER0);
+ writel_relaxed(0, csidev->base + STM32_CSI_IER1);
+
+ /* Disable the CSI */
+ writel_relaxed(0, csidev->base + STM32_CSI_CR);
+
+ pm_runtime_put(csidev->dev);
+}
+
+static int stm32_csi_start_vc(struct stm32_csi_dev *csidev,
+ struct v4l2_subdev_state *state, u32 vc)
+{
+ struct v4l2_mbus_framefmt *mbus_fmt;
+ const struct stm32_csi_fmts *fmt;
+ u32 cfgr1 = 0;
+ int ret = 0;
+ u32 status;
+
+ mbus_fmt = v4l2_subdev_state_get_format(state, STM32_CSI_PAD_SOURCE);
+ fmt = stm32_csi_code_to_fmt(mbus_fmt->code);
+
+ /* If the mbus code is JPEG, don't enable filtering */
+ if (mbus_fmt->code == MEDIA_BUS_FMT_JPEG_1X8) {
+ cfgr1 |= STM32_CSI_VCXCFGR1_ALLDT;
+ cfgr1 |= fmt->input_fmt << STM32_CSI_VCXCFGR1_CDTFT_SHIFT;
+ dev_dbg(csidev->dev, "VC%d: enable AllDT mode\n", vc);
+ } else {
+ cfgr1 |= fmt->datatype << STM32_CSI_VCXCFGR1_DT0_SHIFT;
+ cfgr1 |= fmt->input_fmt << STM32_CSI_VCXCFGR1_DT0FT_SHIFT;
+ cfgr1 |= STM32_CSI_VCXCFGR1_DT0EN;
+ dev_dbg(csidev->dev, "VC%d: enable DT0(0x%x)/DT0FT(0x%x)\n",
+ vc, fmt->datatype, fmt->input_fmt);
+ }
+ writel_relaxed(cfgr1, csidev->base + STM32_CSI_VCXCFGR1(vc));
+
+ /* Enable processing of the virtual-channel and wait for its status */
+ writel_relaxed(STM32_CSI_CR_VCXSTART(vc) | STM32_CSI_CR_CSIEN,
+ csidev->base + STM32_CSI_CR);
+
+ ret = readl_relaxed_poll_timeout(csidev->base + STM32_CSI_SR0,
+ status,
+ status & STM32_CSI_SR0_VCXSTATEF(vc),
+ 1000, 1000000);
+ if (ret) {
+ dev_err(csidev->dev, "failed to start VC(%d)\n", vc);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int stm32_csi_stop_vc(struct stm32_csi_dev *csidev, u32 vc)
+{
+ int ret = 0;
+ u32 status;
+
+ /* Stop the Virtual Channel */
+ writel_relaxed(STM32_CSI_CR_VCXSTOP(vc) | STM32_CSI_CR_CSIEN,
+ csidev->base + STM32_CSI_CR);
+
+ ret = readl_relaxed_poll_timeout(csidev->base + STM32_CSI_SR0,
+ status,
+ !(status & STM32_CSI_SR0_VCXSTATEF(vc)),
+ 1000, 1000000);
+ if (ret) {
+ dev_err(csidev->dev, "failed to stop VC(%d)\n", vc);
+ return ret;
+ }
+
+ /* Disable all DTs */
+ writel_relaxed(0, csidev->base + STM32_CSI_VCXCFGR1(vc));
+ writel_relaxed(0, csidev->base + STM32_CSI_VCXCFGR2(vc));
+
+ return 0;
+}
+
+static int stm32_csi_disable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct stm32_csi_dev *csidev = to_csidev(sd);
+ int ret;
+
+ ret = v4l2_subdev_disable_streams(csidev->s_subdev,
+ csidev->s_subdev_pad_nb, BIT_ULL(0));
+ if (ret)
+ return ret;
+
+ /* Stop the VC0 */
+ ret = stm32_csi_stop_vc(csidev, 0);
+ if (ret)
+ dev_err(csidev->dev, "Failed to stop VC0\n");
+
+ stm32_csi_stop(csidev);
+
+ return 0;
+}
+
+static int stm32_csi_enable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct stm32_csi_dev *csidev = to_csidev(sd);
+ int ret;
+
+ ret = stm32_csi_start(csidev, state);
+ if (ret)
+ return ret;
+
+ /* Configure & start the VC0 */
+ ret = stm32_csi_start_vc(csidev, state, 0);
+ if (ret) {
+ dev_err(csidev->dev, "Failed to start VC0\n");
+ stm32_csi_stop(csidev);
+ return ret;
+ }
+
+ ret = v4l2_subdev_enable_streams(csidev->s_subdev,
+ csidev->s_subdev_pad_nb, BIT_ULL(0));
+ if (ret) {
+ stm32_csi_stop_vc(csidev, 0);
+ stm32_csi_stop(csidev);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int stm32_csi_init_state(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ int i;
+
+ for (i = 0; i < sd->entity.num_pads; i++)
+ *v4l2_subdev_state_get_format(state, i) = fmt_default;
+
+ return 0;
+}
+
+static int stm32_csi_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->index >= ARRAY_SIZE(stm32_csi_formats))
+ return -EINVAL;
+
+ code->code = stm32_csi_formats[code->index].code;
+ return 0;
+}
+
+static int stm32_csi_set_pad_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_format *format)
+{
+ struct stm32_csi_dev *csidev = to_csidev(sd);
+ struct v4l2_mbus_framefmt *framefmt;
+ const struct stm32_csi_fmts *fmt;
+
+ fmt = stm32_csi_code_to_fmt(format->format.code);
+ if (!fmt) {
+ dev_dbg(csidev->dev, "Unsupported code %d, use default\n",
+ format->format.code);
+ format->format.code = fmt_default.code;
+ }
+
+ framefmt = v4l2_subdev_state_get_format(state, STM32_CSI_PAD_SINK);
+
+ if (format->pad == STM32_CSI_PAD_SOURCE)
+ format->format = *framefmt;
+ else
+ *framefmt = format->format;
+
+ framefmt = v4l2_subdev_state_get_format(state, STM32_CSI_PAD_SOURCE);
+ *framefmt = format->format;
+
+ return 0;
+}
+
+static int stm32_csi_log_status(struct v4l2_subdev *sd)
+{
+ struct stm32_csi_dev *csidev = to_csidev(sd);
+ unsigned long flags;
+ unsigned int i;
+
+ spin_lock_irqsave(&csidev->slock, flags);
+
+ for (i = 0; i < STM32_CSI_NUM_SR0_EVENTS; i++) {
+ if (csidev->sr0_counters[i])
+ dev_info(csidev->dev, "%s events: %d\n",
+ stm32_csi_events_sr0[i].name,
+ csidev->sr0_counters[i]);
+ }
+
+ for (i = 0; i < STM32_CSI_NUM_SR1_EVENTS; i++) {
+ if (csidev->sr1_counters[i])
+ dev_info(csidev->dev, "%s events: %d\n",
+ stm32_csi_events_sr1[i].name,
+ csidev->sr1_counters[i]);
+ }
+
+ spin_unlock_irqrestore(&csidev->slock, flags);
+
+ return 0;
+}
+
+static const struct v4l2_subdev_core_ops stm32_csi_core_ops = {
+ .log_status = stm32_csi_log_status,
+};
+
+static const struct v4l2_subdev_video_ops stm32_csi_video_ops = {
+ .s_stream = v4l2_subdev_s_stream_helper,
+};
+
+static const struct v4l2_subdev_pad_ops stm32_csi_pad_ops = {
+ .enum_mbus_code = stm32_csi_enum_mbus_code,
+ .set_fmt = stm32_csi_set_pad_format,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .enable_streams = stm32_csi_enable_streams,
+ .disable_streams = stm32_csi_disable_streams,
+};
+
+static const struct v4l2_subdev_ops stm32_csi_subdev_ops = {
+ .core = &stm32_csi_core_ops,
+ .pad = &stm32_csi_pad_ops,
+ .video = &stm32_csi_video_ops,
+};
+
+static const struct v4l2_subdev_internal_ops stm32_csi_subdev_internal_ops = {
+ .init_state = stm32_csi_init_state,
+};
+
+static int stm32_csi_async_bound(struct v4l2_async_notifier *notifier,
+ struct v4l2_subdev *s_subdev,
+ struct v4l2_async_connection *asd)
+{
+ struct v4l2_subdev *sd = notifier->sd;
+ struct stm32_csi_dev *csidev = to_csidev(sd);
+ int remote_pad;
+
+ remote_pad = media_entity_get_fwnode_pad(&s_subdev->entity,
+ s_subdev->fwnode,
+ MEDIA_PAD_FL_SOURCE);
+ if (remote_pad < 0) {
+ dev_err(csidev->dev, "Couldn't find output pad for subdev %s\n",
+ s_subdev->name);
+ return remote_pad;
+ }
+
+ csidev->s_subdev = s_subdev;
+ csidev->s_subdev_pad_nb = remote_pad;
+
+ return media_create_pad_link(&csidev->s_subdev->entity,
+ remote_pad, &csidev->sd.entity,
+ STM32_CSI_PAD_SINK,
+ MEDIA_LNK_FL_ENABLED |
+ MEDIA_LNK_FL_IMMUTABLE);
+}
+
+static const struct v4l2_async_notifier_operations stm32_csi_notifier_ops = {
+ .bound = stm32_csi_async_bound,
+};
+
+static irqreturn_t stm32_csi_irq_thread(int irq, void *arg)
+{
+ struct stm32_csi_dev *csidev = arg;
+ unsigned long flags;
+ u32 sr0, sr1;
+ int i;
+
+ sr0 = readl_relaxed(csidev->base + STM32_CSI_SR0);
+ sr1 = readl_relaxed(csidev->base + STM32_CSI_SR1);
+
+ /* Clear interrupt */
+ writel_relaxed(sr0 & STM32_CSI_SR0_ERRORS,
+ csidev->base + STM32_CSI_FCR0);
+ writel_relaxed(sr1 & STM32_CSI_SR1_ERRORS,
+ csidev->base + STM32_CSI_FCR1);
+
+ spin_lock_irqsave(&csidev->slock, flags);
+
+ for (i = 0; i < STM32_CSI_NUM_SR0_EVENTS; i++)
+ if (sr0 & stm32_csi_events_sr0[i].mask)
+ csidev->sr0_counters[i]++;
+
+ for (i = 0; i < STM32_CSI_NUM_SR1_EVENTS; i++)
+ if (sr1 & stm32_csi_events_sr1[i].mask)
+ csidev->sr1_counters[i]++;
+
+ spin_unlock_irqrestore(&csidev->slock, flags);
+
+ return IRQ_HANDLED;
+}
+
+static int stm32_csi_get_resources(struct stm32_csi_dev *csidev,
+ struct platform_device *pdev)
+{
+ int irq, ret, i;
+
+ csidev->base = devm_platform_get_and_ioremap_resource(pdev, 0, NULL);
+ if (IS_ERR(csidev->base))
+ return dev_err_probe(&pdev->dev, PTR_ERR(csidev->base),
+ "Failed to ioremap resource\n");
+
+ for (i = 0; i < STM32_CSI_CLK_NB; i++)
+ csidev->clks[i].id = stm32_csi_clks_id[i];
+
+ ret = devm_clk_bulk_get(&pdev->dev, STM32_CSI_CLK_NB,
+ csidev->clks);
+ if (ret < 0)
+ return dev_err_probe(&pdev->dev, ret, "Couldn't get clks\n");
+
+ csidev->supplies[0].supply = "vdd";
+ csidev->supplies[1].supply = "vdda18";
+ ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(csidev->supplies),
+ csidev->supplies);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret,
+ "Failed to request regulator vdd\n");
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+ stm32_csi_irq_thread, IRQF_ONESHOT,
+ dev_name(&pdev->dev), csidev);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret,
+ "Unable to request irq");
+
+ return 0;
+}
+
+static int stm32_csi_parse_dt(struct stm32_csi_dev *csidev)
+{
+ struct v4l2_fwnode_endpoint v4l2_ep = { .bus_type = V4L2_MBUS_CSI2_DPHY };
+ struct v4l2_async_connection *asd;
+ struct fwnode_handle *ep;
+ int ret;
+
+ /* Get bus characteristics from devicetree */
+ ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(csidev->dev), 0, 0,
+ FWNODE_GRAPH_ENDPOINT_NEXT);
+ if (!ep) {
+ dev_err(csidev->dev, "Could not find the endpoint\n");
+ return -ENODEV;
+ }
+
+ ret = v4l2_fwnode_endpoint_parse(ep, &v4l2_ep);
+ fwnode_handle_put(ep);
+ if (ret) {
+ dev_err(csidev->dev, "Could not parse v4l2 endpoint\n");
+ return ret;
+ }
+
+ csidev->num_lanes = v4l2_ep.bus.mipi_csi2.num_data_lanes;
+ if (csidev->num_lanes > STM32_CSI_LANES_MAX) {
+ dev_err(csidev->dev, "Unsupported number of data-lanes: %d\n",
+ csidev->num_lanes);
+ return -EINVAL;
+ }
+
+ memcpy(csidev->lanes, v4l2_ep.bus.mipi_csi2.data_lanes,
+ sizeof(csidev->lanes));
+
+ ep = fwnode_graph_get_next_endpoint(dev_fwnode(csidev->dev), NULL);
+ if (!ep) {
+ dev_err(csidev->dev, "Failed to get next endpoint\n");
+ return -EINVAL;
+ }
+
+ v4l2_async_subdev_nf_init(&csidev->notifier, &csidev->sd);
+
+ asd = v4l2_async_nf_add_fwnode_remote(&csidev->notifier, ep,
+ struct v4l2_async_connection);
+
+ fwnode_handle_put(ep);
+
+ if (IS_ERR(asd)) {
+ dev_err(csidev->dev, "Failed to add fwnode remote subdev\n");
+ return PTR_ERR(asd);
+ }
+
+ csidev->notifier.ops = &stm32_csi_notifier_ops;
+
+ ret = v4l2_async_nf_register(&csidev->notifier);
+ if (ret) {
+ dev_err(csidev->dev, "Failed to register notifier\n");
+ v4l2_async_nf_cleanup(&csidev->notifier);
+ return ret;
+ }
+
+ return ret;
+}
+
+static int stm32_csi_probe(struct platform_device *pdev)
+{
+ struct stm32_csi_dev *csidev;
+ struct reset_control *rstc;
+ int ret;
+
+ csidev = devm_kzalloc(&pdev->dev, sizeof(*csidev), GFP_KERNEL);
+ if (!csidev)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, csidev);
+ csidev->dev = &pdev->dev;
+
+ spin_lock_init(&csidev->slock);
+
+ ret = stm32_csi_get_resources(csidev, pdev);
+ if (ret)
+ goto err_free_priv;
+
+ ret = stm32_csi_parse_dt(csidev);
+ if (ret)
+ goto err_free_priv;
+
+ csidev->sd.owner = THIS_MODULE;
+ csidev->sd.dev = &pdev->dev;
+ csidev->sd.internal_ops = &stm32_csi_subdev_internal_ops;
+ v4l2_subdev_init(&csidev->sd, &stm32_csi_subdev_ops);
+ v4l2_set_subdevdata(&csidev->sd, &pdev->dev);
+ snprintf(csidev->sd.name, sizeof(csidev->sd.name), "%s",
+ dev_name(&pdev->dev));
+
+ /* Create our media pads */
+ csidev->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+ csidev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ csidev->pads[STM32_CSI_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+ csidev->pads[STM32_CSI_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
+
+ ret = media_entity_pads_init(&csidev->sd.entity, STM32_CSI_PAD_MAX,
+ csidev->pads);
+ if (ret)
+ goto err_cleanup;
+
+ ret = v4l2_subdev_init_finalize(&csidev->sd);
+ if (ret < 0)
+ goto err_cleanup;
+
+ ret = v4l2_async_register_subdev(&csidev->sd);
+ if (ret < 0)
+ goto err_cleanup;
+
+ /* Reset device */
+ rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+ if (IS_ERR(rstc)) {
+ ret = dev_err_probe(&pdev->dev, PTR_ERR(rstc),
+ "Couldn't get reset control\n");
+ goto err_cleanup;
+ }
+
+ ret = reset_control_assert(rstc);
+ if (ret) {
+ ret = dev_err_probe(&pdev->dev, ret,
+ "Failed to assert the reset line\n");
+ goto err_cleanup;
+ }
+
+ usleep_range(3000, 5000);
+
+ ret = reset_control_deassert(rstc);
+ if (ret) {
+ ret = dev_err_probe(&pdev->dev, ret,
+ "Failed to deassert the reset line\n");
+ goto err_cleanup;
+ }
+
+ pm_runtime_enable(&pdev->dev);
+
+ dev_info(&pdev->dev,
+ "Probed CSI with %u lanes\n", csidev->num_lanes);
+
+ return 0;
+
+err_cleanup:
+ v4l2_async_nf_cleanup(&csidev->notifier);
+err_free_priv:
+ return ret;
+}
+
+static void stm32_csi_remove(struct platform_device *pdev)
+{
+ struct stm32_csi_dev *csidev = platform_get_drvdata(pdev);
+
+ v4l2_async_unregister_subdev(&csidev->sd);
+
+ pm_runtime_disable(&pdev->dev);
+}
+
+static int stm32_csi_runtime_suspend(struct device *dev)
+{
+ struct stm32_csi_dev *csidev = dev_get_drvdata(dev);
+ int ret;
+
+ clk_bulk_disable_unprepare(STM32_CSI_CLK_NB, csidev->clks);
+
+ ret = regulator_bulk_disable(ARRAY_SIZE(csidev->supplies),
+ csidev->supplies);
+ if (ret < 0)
+ dev_err(dev, "cannot disable regulators %d\n", ret);
+
+ return 0;
+}
+
+static int stm32_csi_runtime_resume(struct device *dev)
+{
+ struct stm32_csi_dev *csidev = dev_get_drvdata(dev);
+ int ret;
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(csidev->supplies),
+ csidev->supplies);
+ if (ret)
+ goto error_out;
+
+ ret = clk_bulk_prepare_enable(STM32_CSI_CLK_NB, csidev->clks);
+ if (ret)
+ goto error_disable_supplies;
+
+ return 0;
+
+error_disable_supplies:
+ ret = regulator_bulk_disable(ARRAY_SIZE(csidev->supplies), csidev->supplies);
+ if (ret < 0)
+ dev_err(dev, "cannot disable regulators %d\n", ret);
+error_out:
+ dev_err(csidev->dev, "Failed to resume: %d\n", ret);
+
+ return ret;
+}
+
+static const struct of_device_id stm32_csi_of_table[] = {
+ { .compatible = "st,stm32mp25-csi", },
+ { /* end node */ },
+};
+MODULE_DEVICE_TABLE(of, stm32_csi_of_table);
+
+static const struct dev_pm_ops stm32_csi_pm_ops = {
+ RUNTIME_PM_OPS(stm32_csi_runtime_suspend,
+ stm32_csi_runtime_resume, NULL)
+};
+
+static struct platform_driver stm32_csi_driver = {
+ .driver = {
+ .name = "stm32-csi",
+ .of_match_table = stm32_csi_of_table,
+ .pm = pm_ptr(&stm32_csi_pm_ops),
+ },
+ .probe = stm32_csi_probe,
+ .remove = stm32_csi_remove,
+};
+
+module_platform_driver(stm32_csi_driver);
+
+MODULE_AUTHOR("Alain Volmat <alain.volmat@foss.st.com>");
+MODULE_DESCRIPTION("STM32 CSI controller");
+MODULE_LICENSE("GPL");
The STM32 CSI controller is tightly coupled with the DCMIPP and act as an input stage to receive data coming from the sensor and transferring them into the DCMIPP. Signed-off-by: Alain Volmat <alain.volmat@foss.st.com> --- v3: get reset controller within probe function and remove it from the driver structure use devm_clk_bulk apis rather 3 separate clks v2: correct data-lanes handling, using values 1 & 2 update yaml filename in MAINTAINERS --- MAINTAINERS | 8 + drivers/media/platform/st/stm32/Kconfig | 14 + drivers/media/platform/st/stm32/Makefile | 1 + drivers/media/platform/st/stm32/stm32-csi.c | 1137 +++++++++++++++++++++++++++ 4 files changed, 1160 insertions(+)