@@ -10,7 +10,8 @@
* - Use grouped parameter hold to update controls atomically
* - Expose debug information through debugfs (FRAME_COUNT, FRAME_STATUS, ...)
* - Make MIPI D-PHY timings configurable
- * - Support the parallel interface
+ * - Program additional parallel interface parameters (slew rates, polarities,
+ * ...)
* - Expose additional controls (in particular the temperature sensor and the
* on-chip black level correction)
*/
@@ -298,6 +299,8 @@
#define AR0144_MIN_CSI2_LINK_FREQ 150000000U
#define AR0144_MAX_CSI2_LINK_FREQ 384000000U
+#define AR0144_MAX_PARALLEL_LINK_FREQ 74250000U
+
/*
* The pixel array contains 1300x820 optically transparent pixels, with 6 dummy
* pixels on each side that can't be read out. The active size is 1288x808.
@@ -464,6 +467,12 @@ static int ar0144_configure_pll(struct ar0144 *sensor)
return ret;
}
+static int ar0144_configure_parallel(struct ar0144 *sensor,
+ const struct ar0144_format_info *info)
+{
+ return cci_write(sensor->regmap, AR0144_SERIAL_FORMAT, 0x0200, NULL);
+}
+
static int ar0144_configure_mipi(struct ar0144 *sensor,
const struct ar0144_format_info *info)
{
@@ -550,13 +559,19 @@ static int ar0144_start_streaming(struct ar0144 *sensor,
if (ret)
return ret;
- ret = ar0144_configure_mipi(sensor, info);
+ if (sensor->bus_cfg.bus_type == V4L2_MBUS_PARALLEL)
+ ret = ar0144_configure_parallel(sensor, info);
+ else
+ ret = ar0144_configure_mipi(sensor, info);
/*
* We're all set, start streaming. Mask bad frames and keep read-only
* registers locked.
*/
val = AR0144_MASK_BAD | AR0144_LOCK_REG | AR0144_STREAM | 0x2010;
+ if (sensor->bus_cfg.bus_type == V4L2_MBUS_PARALLEL)
+ val |= AR0144_SMIA_SERIALIZER_DIS | AR0144_PARALLEL_EN
+ | AR0144_DRIVE_PINS;
cci_write(sensor->regmap, AR0144_RESET_REGISTER, val, &ret);
return ret;
@@ -581,6 +596,10 @@ static int ar0144_stop_streaming(struct ar0144 *sensor)
* Initiate the transition to standby by clearing the STREAM bit. Don't
* clear the bits that affect the output interface yet.
*/
+ if (sensor->bus_cfg.bus_type == V4L2_MBUS_PARALLEL)
+ val |= AR0144_SMIA_SERIALIZER_DIS | AR0144_PARALLEL_EN
+ | AR0144_DRIVE_PINS;
+
ret = cci_write(sensor->regmap, AR0144_RESET_REGISTER, reset_bits, NULL);
if (ret)
return ret;
@@ -1268,6 +1287,10 @@ static int ar0144_get_mbus_config(struct v4l2_subdev *sd, unsigned int pad,
default:
cfg->bus.mipi_csi2 = sensor->bus_cfg.bus.mipi_csi2;
break;
+
+ case V4L2_MBUS_PARALLEL:
+ cfg->bus.parallel = sensor->bus_cfg.bus.parallel;
+ break;
}
return 0;
@@ -1607,6 +1630,10 @@ static int ar0144_parse_dt(struct ar0144 *sensor)
}
break;
+ case V4L2_MBUS_PARALLEL:
+ nlanes = ep->bus.parallel.bus_width ? : 12;
+ break;
+
default:
dev_err(sensor->dev, "Unsupported bus type %u\n", ep->bus_type);
goto error;
Add basic support for the parallel interface. This hasn't been tested due to the lack of a test platform, and will thus likely not work out of the box. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> --- drivers/media/i2c/ar0144.c | 31 +++++++++++++++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-)