| Message ID | 20220525145833.1165437-2-foss+kernel@0leil.net |
|---|---|
| State | New |
| Headers | show |
| Series | None | expand |
Hi Quentin, one more question On Wed, May 25, 2022 at 04:58:31PM +0200, Quentin Schulz wrote: > From: Quentin Schulz <quentin.schulz@theobroma-systems.com> > > Until now, this driver only supported ACPI. This adds support for > Device Tree too while enabling clock and regulators in runtime PM. > > Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> > --- > > v5: > - fixed -Wdeclaration-after-statement for delay_us, > > v4: > - added delays based on clock cycles as specified in datasheet for > pre-power-off and post-power-on, > - re-arranged clk handling, shutdown toggling and regulator handling to > better match power up/down sequence defined in datasheet, > - added comment on need for regulator being stable before releasing > shutdown pin, > > v3: > - added linux/mod_devicetable.h include, > - moved delay for reset pulse right after the regulators are enabled, > - removed check on is_acpi_node in favor of checks on presence of OF > properties (e.g. devm_clk_get_optional returns NULL), > - moved power management out of system suspend/resume into runtime PM > callbacks, > - removed ACPI specific comment since it's not specific to this driver, > - changed devm_clk_get to devm_clk_get_optional, > - remove OF use of clock-frequency (handled by devm_clk_get_optional > directly), > - removed name of clock (only one, so no need for anything explicit) > when requesting a clock from OF, > - wrapped lines to 80 chars, > > v2: > - fixed unused-const-variable warning by removing of_match_ptr in > of_match_table, reported by kernel test robot, > > drivers/media/i2c/ov5675.c | 149 +++++++++++++++++++++++++++++++------ > 1 file changed, 128 insertions(+), 21 deletions(-) > > diff --git a/drivers/media/i2c/ov5675.c b/drivers/media/i2c/ov5675.c > index 82ba9f56baec8..ea801edb8e408 100644 > --- a/drivers/media/i2c/ov5675.c > +++ b/drivers/media/i2c/ov5675.c > @@ -3,10 +3,14 @@ > > #include <asm/unaligned.h> > #include <linux/acpi.h> > +#include <linux/clk.h> > #include <linux/delay.h> > +#include <linux/gpio/consumer.h> > #include <linux/i2c.h> > +#include <linux/mod_devicetable.h> > #include <linux/module.h> > #include <linux/pm_runtime.h> > +#include <linux/regulator/consumer.h> > #include <media/v4l2-ctrls.h> > #include <media/v4l2-device.h> > #include <media/v4l2-fwnode.h> > @@ -17,7 +21,7 @@ > > #define OV5675_LINK_FREQ_450MHZ 450000000ULL > #define OV5675_SCLK 90000000LL > -#define OV5675_MCLK 19200000 > +#define OV5675_XVCLK_19_2 19200000 > #define OV5675_DATA_LANES 2 > #define OV5675_RGB_DEPTH 10 > > @@ -76,6 +80,14 @@ > > #define to_ov5675(_sd) container_of(_sd, struct ov5675, sd) > > +static const char * const ov5675_supply_names[] = { > + "avdd", /* Analog power */ > + "dovdd", /* Digital I/O power */ > + "dvdd", /* Digital core power */ > +}; > + > +#define OV5675_NUM_SUPPLIES ARRAY_SIZE(ov5675_supply_names) > + > enum { > OV5675_LINK_FREQ_900MBPS, > }; > @@ -484,6 +496,9 @@ struct ov5675 { > struct v4l2_subdev sd; > struct media_pad pad; > struct v4l2_ctrl_handler ctrl_handler; > + struct clk *xvclk; > + struct gpio_desc *reset_gpio; > + struct regulator_bulk_data supplies[OV5675_NUM_SUPPLIES]; > > /* V4L2 Controls */ > struct v4l2_ctrl *link_freq; > @@ -944,6 +959,56 @@ static int ov5675_set_stream(struct v4l2_subdev *sd, int enable) > return ret; > } > > +static int ov5675_power_off(struct device *dev) Does this (and power_on) require __maybe_unused to avoid a warning when compiling without CONFIG_PM support ? Have you tried that ? Thanks j > +{ > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > + struct ov5675 *ov5675 = to_ov5675(sd); > + /* 512 xvclk cycles after the last SCCB transation or MIPI frame end */ > + u32 delay_us = DIV_ROUND_UP(512, OV5675_XVCLK_19_2 / 1000 / 1000); > + > + usleep_range(delay_us, delay_us * 2); > + > + clk_disable_unprepare(ov5675->xvclk); > + gpiod_set_value_cansleep(ov5675->reset_gpio, 1); > + regulator_bulk_disable(OV5675_NUM_SUPPLIES, ov5675->supplies); > + > + return 0; > +} > + > +static int ov5675_power_on(struct device *dev) > +{ > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > + struct ov5675 *ov5675 = to_ov5675(sd); > + u32 delay_us = DIV_ROUND_UP(8192, OV5675_XVCLK_19_2 / 1000 / 1000); > + int ret; > + > + ret = clk_prepare_enable(ov5675->xvclk); > + if (ret < 0) { > + dev_err(dev, "failed to enable xvclk: %d\n", ret); > + return ret; > + } > + > + gpiod_set_value_cansleep(ov5675->reset_gpio, 1); > + > + ret = regulator_bulk_enable(OV5675_NUM_SUPPLIES, ov5675->supplies); > + if (ret) { > + clk_disable_unprepare(ov5675->xvclk); > + return ret; > + } > + > + /* Reset pulse should be at least 2ms and reset gpio released only once > + * regulators are stable. > + */ > + usleep_range(2000, 2200); > + > + gpiod_set_value_cansleep(ov5675->reset_gpio, 0); > + > + /* 8192 xvclk cycles prior to the first SCCB transation */ > + usleep_range(delay_us, delay_us * 2); > + > + return 0; > +} > + > static int __maybe_unused ov5675_suspend(struct device *dev) > { > struct v4l2_subdev *sd = dev_get_drvdata(dev); > @@ -1106,32 +1171,60 @@ static const struct v4l2_subdev_internal_ops ov5675_internal_ops = { > .open = ov5675_open, > }; > > -static int ov5675_check_hwcfg(struct device *dev) > +static int ov5675_get_hwcfg(struct ov5675 *ov5675, struct device *dev) > { > struct fwnode_handle *ep; > struct fwnode_handle *fwnode = dev_fwnode(dev); > struct v4l2_fwnode_endpoint bus_cfg = { > .bus_type = V4L2_MBUS_CSI2_DPHY > }; > - u32 mclk; > + u32 xvclk_rate; > int ret; > unsigned int i, j; > > if (!fwnode) > return -ENXIO; > > - ret = fwnode_property_read_u32(fwnode, "clock-frequency", &mclk); > + ov5675->xvclk = devm_clk_get_optional(dev, NULL); > + if (IS_ERR(ov5675->xvclk)) > + return dev_err_probe(dev, PTR_ERR(ov5675->xvclk), > + "failed to get xvclk: %ld\n", > + PTR_ERR(ov5675->xvclk)); > > - if (ret) { > - dev_err(dev, "can't get clock frequency"); > - return ret; > + if (ov5675->xvclk) { > + xvclk_rate = clk_get_rate(ov5675->xvclk); > + } else { > + ret = fwnode_property_read_u32(fwnode, "clock-frequency", > + &xvclk_rate); > + > + if (ret) { > + dev_err(dev, "can't get clock frequency"); > + return ret; > + } > } > > - if (mclk != OV5675_MCLK) { > - dev_err(dev, "external clock %d is not supported", mclk); > + if (xvclk_rate != OV5675_XVCLK_19_2) { > + dev_err(dev, "external clock rate %u is unsupported", > + xvclk_rate); > return -EINVAL; > } > > + ov5675->reset_gpio = devm_gpiod_get_optional(dev, "reset", > + GPIOD_OUT_HIGH); > + if (IS_ERR(ov5675->reset_gpio)) { > + ret = PTR_ERR(ov5675->reset_gpio); > + dev_err(dev, "failed to get reset-gpios: %d\n", ret); > + return ret; > + } > + > + for (i = 0; i < OV5675_NUM_SUPPLIES; i++) > + ov5675->supplies[i].supply = ov5675_supply_names[i]; > + > + ret = devm_regulator_bulk_get(dev, OV5675_NUM_SUPPLIES, > + ov5675->supplies); > + if (ret) > + return ret; > + > ep = fwnode_graph_get_next_endpoint(fwnode, NULL); > if (!ep) > return -ENXIO; > @@ -1186,6 +1279,9 @@ static int ov5675_remove(struct i2c_client *client) > pm_runtime_disable(&client->dev); > mutex_destroy(&ov5675->mutex); > > + if (!pm_runtime_status_suspended(&client->dev)) > + ov5675_power_off(&client->dev); > + > return 0; > } > > @@ -1195,25 +1291,31 @@ static int ov5675_probe(struct i2c_client *client) > bool full_power; > int ret; > > - ret = ov5675_check_hwcfg(&client->dev); > + ov5675 = devm_kzalloc(&client->dev, sizeof(*ov5675), GFP_KERNEL); > + if (!ov5675) > + return -ENOMEM; > + > + ret = ov5675_get_hwcfg(ov5675, &client->dev); > if (ret) { > - dev_err(&client->dev, "failed to check HW configuration: %d", > + dev_err(&client->dev, "failed to get HW configuration: %d", > ret); > return ret; > } > > - ov5675 = devm_kzalloc(&client->dev, sizeof(*ov5675), GFP_KERNEL); > - if (!ov5675) > - return -ENOMEM; > - > v4l2_i2c_subdev_init(&ov5675->sd, client, &ov5675_subdev_ops); > > + ret = ov5675_power_on(&client->dev); > + if (ret) { > + dev_err(&client->dev, "failed to power on: %d\n", ret); > + return ret; > + } > + > full_power = acpi_dev_state_d0(&client->dev); > if (full_power) { > ret = ov5675_identify_module(ov5675); > if (ret) { > dev_err(&client->dev, "failed to find sensor: %d", ret); > - return ret; > + goto probe_power_off; > } > } > > @@ -1243,11 +1345,6 @@ static int ov5675_probe(struct i2c_client *client) > goto probe_error_media_entity_cleanup; > } > > - /* > - * Device is already turned on by i2c-core with ACPI domain PM. > - * Enable runtime PM and turn off the device. > - */ > - > /* Set the device's state to active if it's in D0 state. */ > if (full_power) > pm_runtime_set_active(&client->dev); > @@ -1262,12 +1359,15 @@ static int ov5675_probe(struct i2c_client *client) > probe_error_v4l2_ctrl_handler_free: > v4l2_ctrl_handler_free(ov5675->sd.ctrl_handler); > mutex_destroy(&ov5675->mutex); > +probe_power_off: > + ov5675_power_off(&client->dev); > > return ret; > } > > static const struct dev_pm_ops ov5675_pm_ops = { > SET_SYSTEM_SLEEP_PM_OPS(ov5675_suspend, ov5675_resume) > + SET_RUNTIME_PM_OPS(ov5675_power_off, ov5675_power_on, NULL) > }; > > #ifdef CONFIG_ACPI > @@ -1279,11 +1379,18 @@ static const struct acpi_device_id ov5675_acpi_ids[] = { > MODULE_DEVICE_TABLE(acpi, ov5675_acpi_ids); > #endif > > +static const struct of_device_id ov5675_of_match[] = { > + { .compatible = "ovti,ov5675", }, > + { /* sentinel */ }, > +}; > +MODULE_DEVICE_TABLE(of, ov5675_of_match); > + > static struct i2c_driver ov5675_i2c_driver = { > .driver = { > .name = "ov5675", > .pm = &ov5675_pm_ops, > .acpi_match_table = ACPI_PTR(ov5675_acpi_ids), > + .of_match_table = ov5675_of_match, > }, > .probe_new = ov5675_probe, > .remove = ov5675_remove, > -- > 2.36.1 >
Hi Jacopo, On 5/31/22 15:16, Jacopo Mondi wrote: > Hi Quentin, > one more question > > On Wed, May 25, 2022 at 04:58:31PM +0200, Quentin Schulz wrote: >> From: Quentin Schulz <quentin.schulz@theobroma-systems.com> >> >> Until now, this driver only supported ACPI. This adds support for >> Device Tree too while enabling clock and regulators in runtime PM. >> >> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com> >> --- >> >> v5: >> - fixed -Wdeclaration-after-statement for delay_us, >> >> v4: >> - added delays based on clock cycles as specified in datasheet for >> pre-power-off and post-power-on, >> - re-arranged clk handling, shutdown toggling and regulator handling to >> better match power up/down sequence defined in datasheet, >> - added comment on need for regulator being stable before releasing >> shutdown pin, >> >> v3: >> - added linux/mod_devicetable.h include, >> - moved delay for reset pulse right after the regulators are enabled, >> - removed check on is_acpi_node in favor of checks on presence of OF >> properties (e.g. devm_clk_get_optional returns NULL), >> - moved power management out of system suspend/resume into runtime PM >> callbacks, >> - removed ACPI specific comment since it's not specific to this driver, >> - changed devm_clk_get to devm_clk_get_optional, >> - remove OF use of clock-frequency (handled by devm_clk_get_optional >> directly), >> - removed name of clock (only one, so no need for anything explicit) >> when requesting a clock from OF, >> - wrapped lines to 80 chars, >> >> v2: >> - fixed unused-const-variable warning by removing of_match_ptr in >> of_match_table, reported by kernel test robot, >> >> drivers/media/i2c/ov5675.c | 149 +++++++++++++++++++++++++++++++------ >> 1 file changed, 128 insertions(+), 21 deletions(-) >> >> diff --git a/drivers/media/i2c/ov5675.c b/drivers/media/i2c/ov5675.c >> index 82ba9f56baec8..ea801edb8e408 100644 >> --- a/drivers/media/i2c/ov5675.c >> +++ b/drivers/media/i2c/ov5675.c >> @@ -3,10 +3,14 @@ >> >> #include <asm/unaligned.h> >> #include <linux/acpi.h> >> +#include <linux/clk.h> >> #include <linux/delay.h> >> +#include <linux/gpio/consumer.h> >> #include <linux/i2c.h> >> +#include <linux/mod_devicetable.h> >> #include <linux/module.h> >> #include <linux/pm_runtime.h> >> +#include <linux/regulator/consumer.h> >> #include <media/v4l2-ctrls.h> >> #include <media/v4l2-device.h> >> #include <media/v4l2-fwnode.h> >> @@ -17,7 +21,7 @@ >> >> #define OV5675_LINK_FREQ_450MHZ 450000000ULL >> #define OV5675_SCLK 90000000LL >> -#define OV5675_MCLK 19200000 >> +#define OV5675_XVCLK_19_2 19200000 >> #define OV5675_DATA_LANES 2 >> #define OV5675_RGB_DEPTH 10 >> >> @@ -76,6 +80,14 @@ >> >> #define to_ov5675(_sd) container_of(_sd, struct ov5675, sd) >> >> +static const char * const ov5675_supply_names[] = { >> + "avdd", /* Analog power */ >> + "dovdd", /* Digital I/O power */ >> + "dvdd", /* Digital core power */ >> +}; >> + >> +#define OV5675_NUM_SUPPLIES ARRAY_SIZE(ov5675_supply_names) >> + >> enum { >> OV5675_LINK_FREQ_900MBPS, >> }; >> @@ -484,6 +496,9 @@ struct ov5675 { >> struct v4l2_subdev sd; >> struct media_pad pad; >> struct v4l2_ctrl_handler ctrl_handler; >> + struct clk *xvclk; >> + struct gpio_desc *reset_gpio; >> + struct regulator_bulk_data supplies[OV5675_NUM_SUPPLIES]; >> >> /* V4L2 Controls */ >> struct v4l2_ctrl *link_freq; >> @@ -944,6 +959,56 @@ static int ov5675_set_stream(struct v4l2_subdev *sd, int enable) >> return ret; >> } >> >> +static int ov5675_power_off(struct device *dev) > > Does this (and power_on) require __maybe_unused to avoid a warning > when compiling without CONFIG_PM support ? Have you tried that ? > It does not, because they are called manually in the probe function and its error path (but thanks for the heads up, because I definitely forgot about this one). I received some review outside of this mailing list telling me the error path is incorrect for pm_runtime so I'll have a look at it before sending a v6. Cheers, Quentin
diff --git a/drivers/media/i2c/ov5675.c b/drivers/media/i2c/ov5675.c index 82ba9f56baec8..ea801edb8e408 100644 --- a/drivers/media/i2c/ov5675.c +++ b/drivers/media/i2c/ov5675.c @@ -3,10 +3,14 @@ #include <asm/unaligned.h> #include <linux/acpi.h> +#include <linux/clk.h> #include <linux/delay.h> +#include <linux/gpio/consumer.h> #include <linux/i2c.h> +#include <linux/mod_devicetable.h> #include <linux/module.h> #include <linux/pm_runtime.h> +#include <linux/regulator/consumer.h> #include <media/v4l2-ctrls.h> #include <media/v4l2-device.h> #include <media/v4l2-fwnode.h> @@ -17,7 +21,7 @@ #define OV5675_LINK_FREQ_450MHZ 450000000ULL #define OV5675_SCLK 90000000LL -#define OV5675_MCLK 19200000 +#define OV5675_XVCLK_19_2 19200000 #define OV5675_DATA_LANES 2 #define OV5675_RGB_DEPTH 10 @@ -76,6 +80,14 @@ #define to_ov5675(_sd) container_of(_sd, struct ov5675, sd) +static const char * const ov5675_supply_names[] = { + "avdd", /* Analog power */ + "dovdd", /* Digital I/O power */ + "dvdd", /* Digital core power */ +}; + +#define OV5675_NUM_SUPPLIES ARRAY_SIZE(ov5675_supply_names) + enum { OV5675_LINK_FREQ_900MBPS, }; @@ -484,6 +496,9 @@ struct ov5675 { struct v4l2_subdev sd; struct media_pad pad; struct v4l2_ctrl_handler ctrl_handler; + struct clk *xvclk; + struct gpio_desc *reset_gpio; + struct regulator_bulk_data supplies[OV5675_NUM_SUPPLIES]; /* V4L2 Controls */ struct v4l2_ctrl *link_freq; @@ -944,6 +959,56 @@ static int ov5675_set_stream(struct v4l2_subdev *sd, int enable) return ret; } +static int ov5675_power_off(struct device *dev) +{ + struct v4l2_subdev *sd = dev_get_drvdata(dev); + struct ov5675 *ov5675 = to_ov5675(sd); + /* 512 xvclk cycles after the last SCCB transation or MIPI frame end */ + u32 delay_us = DIV_ROUND_UP(512, OV5675_XVCLK_19_2 / 1000 / 1000); + + usleep_range(delay_us, delay_us * 2); + + clk_disable_unprepare(ov5675->xvclk); + gpiod_set_value_cansleep(ov5675->reset_gpio, 1); + regulator_bulk_disable(OV5675_NUM_SUPPLIES, ov5675->supplies); + + return 0; +} + +static int ov5675_power_on(struct device *dev) +{ + struct v4l2_subdev *sd = dev_get_drvdata(dev); + struct ov5675 *ov5675 = to_ov5675(sd); + u32 delay_us = DIV_ROUND_UP(8192, OV5675_XVCLK_19_2 / 1000 / 1000); + int ret; + + ret = clk_prepare_enable(ov5675->xvclk); + if (ret < 0) { + dev_err(dev, "failed to enable xvclk: %d\n", ret); + return ret; + } + + gpiod_set_value_cansleep(ov5675->reset_gpio, 1); + + ret = regulator_bulk_enable(OV5675_NUM_SUPPLIES, ov5675->supplies); + if (ret) { + clk_disable_unprepare(ov5675->xvclk); + return ret; + } + + /* Reset pulse should be at least 2ms and reset gpio released only once + * regulators are stable. + */ + usleep_range(2000, 2200); + + gpiod_set_value_cansleep(ov5675->reset_gpio, 0); + + /* 8192 xvclk cycles prior to the first SCCB transation */ + usleep_range(delay_us, delay_us * 2); + + return 0; +} + static int __maybe_unused ov5675_suspend(struct device *dev) { struct v4l2_subdev *sd = dev_get_drvdata(dev); @@ -1106,32 +1171,60 @@ static const struct v4l2_subdev_internal_ops ov5675_internal_ops = { .open = ov5675_open, }; -static int ov5675_check_hwcfg(struct device *dev) +static int ov5675_get_hwcfg(struct ov5675 *ov5675, struct device *dev) { struct fwnode_handle *ep; struct fwnode_handle *fwnode = dev_fwnode(dev); struct v4l2_fwnode_endpoint bus_cfg = { .bus_type = V4L2_MBUS_CSI2_DPHY }; - u32 mclk; + u32 xvclk_rate; int ret; unsigned int i, j; if (!fwnode) return -ENXIO; - ret = fwnode_property_read_u32(fwnode, "clock-frequency", &mclk); + ov5675->xvclk = devm_clk_get_optional(dev, NULL); + if (IS_ERR(ov5675->xvclk)) + return dev_err_probe(dev, PTR_ERR(ov5675->xvclk), + "failed to get xvclk: %ld\n", + PTR_ERR(ov5675->xvclk)); - if (ret) { - dev_err(dev, "can't get clock frequency"); - return ret; + if (ov5675->xvclk) { + xvclk_rate = clk_get_rate(ov5675->xvclk); + } else { + ret = fwnode_property_read_u32(fwnode, "clock-frequency", + &xvclk_rate); + + if (ret) { + dev_err(dev, "can't get clock frequency"); + return ret; + } } - if (mclk != OV5675_MCLK) { - dev_err(dev, "external clock %d is not supported", mclk); + if (xvclk_rate != OV5675_XVCLK_19_2) { + dev_err(dev, "external clock rate %u is unsupported", + xvclk_rate); return -EINVAL; } + ov5675->reset_gpio = devm_gpiod_get_optional(dev, "reset", + GPIOD_OUT_HIGH); + if (IS_ERR(ov5675->reset_gpio)) { + ret = PTR_ERR(ov5675->reset_gpio); + dev_err(dev, "failed to get reset-gpios: %d\n", ret); + return ret; + } + + for (i = 0; i < OV5675_NUM_SUPPLIES; i++) + ov5675->supplies[i].supply = ov5675_supply_names[i]; + + ret = devm_regulator_bulk_get(dev, OV5675_NUM_SUPPLIES, + ov5675->supplies); + if (ret) + return ret; + ep = fwnode_graph_get_next_endpoint(fwnode, NULL); if (!ep) return -ENXIO; @@ -1186,6 +1279,9 @@ static int ov5675_remove(struct i2c_client *client) pm_runtime_disable(&client->dev); mutex_destroy(&ov5675->mutex); + if (!pm_runtime_status_suspended(&client->dev)) + ov5675_power_off(&client->dev); + return 0; } @@ -1195,25 +1291,31 @@ static int ov5675_probe(struct i2c_client *client) bool full_power; int ret; - ret = ov5675_check_hwcfg(&client->dev); + ov5675 = devm_kzalloc(&client->dev, sizeof(*ov5675), GFP_KERNEL); + if (!ov5675) + return -ENOMEM; + + ret = ov5675_get_hwcfg(ov5675, &client->dev); if (ret) { - dev_err(&client->dev, "failed to check HW configuration: %d", + dev_err(&client->dev, "failed to get HW configuration: %d", ret); return ret; } - ov5675 = devm_kzalloc(&client->dev, sizeof(*ov5675), GFP_KERNEL); - if (!ov5675) - return -ENOMEM; - v4l2_i2c_subdev_init(&ov5675->sd, client, &ov5675_subdev_ops); + ret = ov5675_power_on(&client->dev); + if (ret) { + dev_err(&client->dev, "failed to power on: %d\n", ret); + return ret; + } + full_power = acpi_dev_state_d0(&client->dev); if (full_power) { ret = ov5675_identify_module(ov5675); if (ret) { dev_err(&client->dev, "failed to find sensor: %d", ret); - return ret; + goto probe_power_off; } } @@ -1243,11 +1345,6 @@ static int ov5675_probe(struct i2c_client *client) goto probe_error_media_entity_cleanup; } - /* - * Device is already turned on by i2c-core with ACPI domain PM. - * Enable runtime PM and turn off the device. - */ - /* Set the device's state to active if it's in D0 state. */ if (full_power) pm_runtime_set_active(&client->dev); @@ -1262,12 +1359,15 @@ static int ov5675_probe(struct i2c_client *client) probe_error_v4l2_ctrl_handler_free: v4l2_ctrl_handler_free(ov5675->sd.ctrl_handler); mutex_destroy(&ov5675->mutex); +probe_power_off: + ov5675_power_off(&client->dev); return ret; } static const struct dev_pm_ops ov5675_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(ov5675_suspend, ov5675_resume) + SET_RUNTIME_PM_OPS(ov5675_power_off, ov5675_power_on, NULL) }; #ifdef CONFIG_ACPI @@ -1279,11 +1379,18 @@ static const struct acpi_device_id ov5675_acpi_ids[] = { MODULE_DEVICE_TABLE(acpi, ov5675_acpi_ids); #endif +static const struct of_device_id ov5675_of_match[] = { + { .compatible = "ovti,ov5675", }, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, ov5675_of_match); + static struct i2c_driver ov5675_i2c_driver = { .driver = { .name = "ov5675", .pm = &ov5675_pm_ops, .acpi_match_table = ACPI_PTR(ov5675_acpi_ids), + .of_match_table = ov5675_of_match, }, .probe_new = ov5675_probe, .remove = ov5675_remove,