@@ -104,7 +104,6 @@ struct ov5647 {
struct v4l2_subdev sd;
struct media_pad pad;
struct mutex lock;
- int power_count;
struct clk *xclk;
struct gpio_desc *pwdn;
bool clock_ncont;
@@ -1354,6 +1353,8 @@ static int ov5647_s_ctrl(struct v4l2_ctrl *ctrl)
struct ov5647, ctrls);
struct v4l2_subdev *sd = &sensor->sd;
struct i2c_client *client = v4l2_get_subdevdata(sd);
+ int ret = 0;
+
/* v4l2_ctrl_lock() locks our own mutex */
@@ -1370,33 +1371,40 @@ static int ov5647_s_ctrl(struct v4l2_ctrl *ctrl)
}
/*
- * If the device is not powered up by the host driver do
- * not apply any controls to H/W at this time. Instead
- * the controls will be restored at s_stream(1) time.
+ * If the device is not powered up do not apply any controls
+ * to H/W at this time. Instead the controls will be restored
+ * at s_stream(1) time.
*/
- if (!sensor->power_count)
+ if (pm_runtime_get_if_in_use(&client->dev) == 0)
return 0;
switch (ctrl->id) {
case V4L2_CID_AUTO_WHITE_BALANCE:
- return ov5647_s_auto_white_balance(sd, ctrl->val);
+ ret = ov5647_s_auto_white_balance(sd, ctrl->val);
+ break;
case V4L2_CID_AUTOGAIN:
- return ov5647_s_autogain(sd, ctrl->val);
+ ret = ov5647_s_autogain(sd, ctrl->val);
+ break;
case V4L2_CID_EXPOSURE_AUTO:
- return ov5647_s_exposure_auto(sd, ctrl->val);
+ ret = ov5647_s_exposure_auto(sd, ctrl->val);
+ break;
case V4L2_CID_ANALOGUE_GAIN:
- return ov5647_s_analogue_gain(sd, ctrl->val);
+ ret = ov5647_s_analogue_gain(sd, ctrl->val);
+ break;
case V4L2_CID_EXPOSURE:
- return ov5647_s_exposure(sd, ctrl->val);
+ ret = ov5647_s_exposure(sd, ctrl->val);
+ break;
+ case V4L2_CID_VBLANK:
+ ret = ov5647_write16(sd, OV5647_REG_VTS_HI,
+ sensor->mode->format.height + ctrl->val);
+ break;
+
+ /* Read-only, but we adjust it based on mode. */
case V4L2_CID_PIXEL_RATE:
- /* Read-only, but we adjust it based on mode. */
- return 0;
case V4L2_CID_HBLANK:
/* Read-only, but we adjust it based on mode. */
- return 0;
- case V4L2_CID_VBLANK:
- return ov5647_write16(sd, OV5647_REG_VTS_HI,
- sensor->mode->format.height + ctrl->val);
+ break;
+
default:
dev_info(&client->dev,
"Control (id:0x%x, val:0x%x) not supported\n",
@@ -1404,7 +1412,9 @@ static int ov5647_s_ctrl(struct v4l2_ctrl *ctrl)
return -EINVAL;
}
- return 0;
+ pm_runtime_put(&client->dev);
+
+ return ret;
}
static const struct v4l2_ctrl_ops ov5647_ctrl_ops = {
Use pm_runtime_get_if_in_use() in s_ctrl to apply controls only when the device is powered on. Rework the control set function to balance the pm_runtime_get_if_in_use() call with pm_runtime_put() at the end of the function. Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> --- drivers/media/i2c/ov5647.c | 44 +++++++++++++++++++++++--------------- 1 file changed, 27 insertions(+), 17 deletions(-)