| Message ID | 20191011035613.13598-1-manivannan.sadhasivam@linaro.org |
|---|---|
| Headers | show |
| Series | Add IMX296 CMOS image sensor support | expand |
On Fri, Oct 11, 2019 at 09:26:12AM +0530, Manivannan Sadhasivam wrote: > Add devicetree binding for IMX296 CMOS image sensor. > > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> > --- > .../devicetree/bindings/media/i2c/imx296.txt | 55 +++++++++++++++++++ > 1 file changed, 55 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/imx296.txt You should know by now, use DT schema format please. > diff --git a/Documentation/devicetree/bindings/media/i2c/imx296.txt b/Documentation/devicetree/bindings/media/i2c/imx296.txt > new file mode 100644 > index 000000000000..25d3b15162c1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/imx296.txt > @@ -0,0 +1,55 @@ > +* Sony IMX296 1/2.8-Inch CMOS Image Sensor > + > +The Sony IMX296 is a 1/2.9-Inch active pixel type CMOS Solid-state image > +sensor with square pixel array and 1.58 M effective pixels. This chip features > +a global shutter with variable charge-integration time. It is programmable > +through I2C and 4-wire interfaces. The sensor output is available via CSI-2 > +serial data output (1 Lane). > + > +Required Properties: > +- compatible: Should be "sony,imx296" > +- reg: I2C bus address of the device > +- clocks: Reference to the mclk clock. > +- clock-names: Should be "mclk". > +- clock-frequency: Frequency of the mclk clock in Hz. > +- vddo-supply: Interface power supply. > +- vdda-supply: Analog power supply. > +- vddd-supply: Digital power supply. > + > +Optional Properties: > +- reset-gpios: Sensor reset GPIO > + > +The imx296 device node should contain one 'port' child node with > +an 'endpoint' subnode. For further reading on port node refer to > +Documentation/devicetree/bindings/media/video-interfaces.txt. > + > +Required Properties on endpoint: > +- data-lanes: check ../video-interfaces.txt This should only be required when not using all the lanes on the device. > +- remote-endpoint: check ../video-interfaces.txt Don't really need to document this. > + > +Example: > + &i2c1 { > + ... > + imx296: camera-sensor@1a { > + compatible = "sony,imx296"; > + reg = <0x1a>; > + > + reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&camera_rear_default>; > + > + clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; > + clock-names = "mclk"; > + clock-frequency = <37125000>; > + > + vddo-supply = <&camera_vddo_1v8>; > + vdda-supply = <&camera_vdda_3v3>; > + vddd-supply = <&camera_vddd_1v2>; > + > + port { > + imx296_ep: endpoint { > + data-lanes = <1>; > + remote-endpoint = <&csiphy0_ep>; > + }; > + }; > + }; > -- > 2.17.1 >