diff mbox series

[RFT,v8,5/6] ARM: pxa: Convert gumstix Bluetooth to GPIO descriptors

Message ID 20231011-pxa-gpio-v8-5-eed08a0fcac8@skole.hr
State New
Headers show
Series ARM: pxa: GPIO descriptor conversions | expand

Commit Message

Duje Mihanović Oct. 11, 2023, 1:23 p.m. UTC 
Gumstix still uses the legacy GPIO interface for resetting the Bluetooth
device.

Convert it to use the GPIO descriptor interface.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
 arch/arm/mach-pxa/gumstix.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c
index c9f0f62187bd..0bca6e2c80a9 100644
--- a/arch/arm/mach-pxa/gumstix.c
+++ b/arch/arm/mach-pxa/gumstix.c
@@ -20,8 +20,8 @@ 
 #include <linux/delay.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
+#include <linux/gpio/consumer.h>
 #include <linux/gpio/machine.h>
-#include <linux/gpio.h>
 #include <linux/err.h>
 #include <linux/clk.h>
 
@@ -129,6 +129,11 @@  static void gumstix_udc_init(void)
 #endif
 
 #ifdef CONFIG_BT
+GPIO_LOOKUP_SINGLE(gumstix_bt_gpio_table, "pxa2xx-uart.1", "pxa-gpio",
+		GPIO_GUMSTIX_BTRESET, "BTRST", GPIO_ACTIVE_LOW);
+
+static struct gpio_desc *bt_reset;
+
 /* Normally, the bootloader would have enabled this 32kHz clock but many
 ** boards still have u-boot 1.1.4 so we check if it has been turned on and
 ** if not, we turn it on with a warning message. */
@@ -153,24 +158,19 @@  static void gumstix_setup_bt_clock(void)
 
 static void __init gumstix_bluetooth_init(void)
 {
-	int err;
+	gpiod_add_lookup_table(&gumstix_bt_gpio_table);
 
 	gumstix_setup_bt_clock();
 
-	err = gpio_request(GPIO_GUMSTIX_BTRESET, "BTRST");
-	if (err) {
+	bt_reset = gpiod_get(&pxa_device_btuart.dev, "BTRST", GPIOD_OUT_HIGH);
+	if (IS_ERR(bt_reset)) {
 		pr_err("gumstix: failed request gpio for bluetooth reset\n");
 		return;
 	}
 
-	err = gpio_direction_output(GPIO_GUMSTIX_BTRESET, 1);
-	if (err) {
-		pr_err("gumstix: can't reset bluetooth\n");
-		return;
-	}
-	gpio_set_value(GPIO_GUMSTIX_BTRESET, 0);
+	gpiod_set_value(bt_reset, 1);
 	udelay(100);
-	gpio_set_value(GPIO_GUMSTIX_BTRESET, 1);
+	gpiod_set_value(bt_reset, 0);
 }
 #else
 static void gumstix_bluetooth_init(void)