[v2,33/46] mfd: ti_am335x_tscadc: Move control register configuration

The datasheet states that most of the configuration should be set in the
control register in the first place, before actually enabling the
hardware. So far only half of the configuration was made in the first
step, which does not make really sense and would complicating the code
when introducing support for the am437x hardware.

Let's move that register write a bit below to enclose more configuration.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/mfd/ti_am335x_tscadc.c | 2 ++
 1 file changed, 2 insertions(+)

On 03/09/2021 00:51, Miquel Raynal wrote:
> The datasheet states that most of the configuration should be set in the

> control register in the first place, before actually enabling the

> hardware. So far only half of the configuration was made in the first

> step, which does not make really sense and would complicating the code

> when introducing support for the am437x hardware.

> 

> Let's move that register write a bit below to enclose more configuration.

> 

> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

> ---

>   drivers/mfd/ti_am335x_tscadc.c | 2 ++

>   1 file changed, 2 insertions(+)

> 

> diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c

> index 29ada9da8826..a0db3e4ff265 100644

> --- a/drivers/mfd/ti_am335x_tscadc.c

> +++ b/drivers/mfd/ti_am335x_tscadc.c

> @@ -239,6 +239,8 @@ static	int ti_tscadc_probe(struct platform_device *pdev)

>   	}

>   	regmap_write(tscadc->regmap, REG_CTRL, tscadc->ctrl);

>   

> +	regmap_write(tscadc->regmap, REG_CTRL, tscadc->ctrl);

> +


Strange change - above 2 lines a the same !?

>   	tscadc_idle_config(tscadc);

>   

>   	/* Enable the TSC module enable bit */

> 


-- 
Best regards,
grygorii

Hi Jonathan,

jic23@kernel.org wrote on Sun, 5 Sep 2021 14:18:52 +0100:

> On Fri, 3 Sep 2021 16:24:22 +0300
> Grygorii Strashko <grygorii.strashko@ti.com> wrote:
> 
> > On 03/09/2021 00:51, Miquel Raynal wrote:  
> > > The datasheet states that most of the configuration should be set in the
> > > control register in the first place, before actually enabling the
> > > hardware. So far only half of the configuration was made in the first
> > > step, which does not make really sense and would complicating the code
> > > when introducing support for the am437x hardware.
> > > 
> > > Let's move that register write a bit below to enclose more configuration.
> > > 
> > > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> > > ---
> > >   drivers/mfd/ti_am335x_tscadc.c | 2 ++
> > >   1 file changed, 2 insertions(+)
> > > 
> > > diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
> > > index 29ada9da8826..a0db3e4ff265 100644
> > > --- a/drivers/mfd/ti_am335x_tscadc.c
> > > +++ b/drivers/mfd/ti_am335x_tscadc.c
> > > @@ -239,6 +239,8 @@ static	int ti_tscadc_probe(struct platform_device *pdev)
> > >   	}
> > >   	regmap_write(tscadc->regmap, REG_CTRL, tscadc->ctrl);
> > >   
> > > +	regmap_write(tscadc->regmap, REG_CTRL, tscadc->ctrl);
> > > +    
> > 
> > Strange change - above 2 lines a the same !?  
> 
> Yup, Looks like this one got handled earlier and the rebase went wrong.
> So drop it.

Exactly. That's a rebase issue I didn't notice.

Thanks,
Miquèl