@@ -19892,6 +19892,7 @@ M: Chris Packham <chris.packham@alliedtelesis.co.nz>
L: linux-i2c@vger.kernel.org
S: Maintained
F: Documentation/devicetree/bindings/i2c/realtek,rtl9300-i2c.yaml
+F: drivers/i2c/busses/i2c-rtl9300.c
RTRS TRANSPORT DRIVERS
M: Md. Haris Iqbal <haris.iqbal@ionos.com>
@@ -1041,6 +1041,16 @@ config I2C_RK3X
This driver can also be built as a module. If so, the module will
be called i2c-rk3x.
+config I2C_RTL9300
+ tristate "Realtek RTL9300 I2C controller"
+ depends on MACH_REALTEK_RTL || COMPILE_TEST
+ help
+ Say Y here to include support for the I2C controller in Realtek
+ RTL9300 SoCs.
+
+ This driver can also be built as a module. If so, the module will
+ be called i2c-rtl9300.
+
config I2C_RZV2M
tristate "Renesas RZ/V2M adapter"
depends on ARCH_RENESAS || COMPILE_TEST
@@ -102,6 +102,7 @@ obj-$(CONFIG_I2C_QCOM_GENI) += i2c-qcom-geni.o
obj-$(CONFIG_I2C_QUP) += i2c-qup.o
obj-$(CONFIG_I2C_RIIC) += i2c-riic.o
obj-$(CONFIG_I2C_RK3X) += i2c-rk3x.o
+obj-$(CONFIG_I2C_RTL9300) += i2c-rtl9300.o
obj-$(CONFIG_I2C_RZV2M) += i2c-rzv2m.o
obj-$(CONFIG_I2C_S3C2410) += i2c-s3c2410.o
obj-$(CONFIG_I2C_SH7760) += i2c-sh7760.o
new file mode 100644
@@ -0,0 +1,377 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/i2c.h>
+#include <linux/mod_devicetable.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+struct rtl9300_i2c {
+ struct regmap *regmap;
+ struct device *dev;
+ struct i2c_adapter adap;
+ u32 i2c_mst_ofs;
+ u32 i2c_mst_glb_ofs;
+ u8 bus_freq;
+ u8 sda_pin;
+};
+
+#define I2C_MST_CTRL1 0x0
+#define MEM_ADDR_OFS 8
+#define MEM_ADDR_MASK 0xffffff
+#define SDA_OUT_SEL_OFS 4
+#define SDA_OUT_SEL_MASK 0x7
+#define GPIO_SCL_SEL BIT(3)
+#define RWOP BIT(2)
+#define I2C_FAIL BIT(1)
+#define I2C_TRIG BIT(0)
+#define I2C_MST_CTRL2 0x4
+#define RD_MODE BIT(15)
+#define DEV_ADDR_OFS 8
+#define DEV_ADDR_MASK 0x7f
+#define DATA_WIDTH_OFS 4
+#define DATA_WIDTH_MASK 0xf
+#define MEM_ADDR_WIDTH_OFS 2
+#define MEM_ADDR_WIDTH_MASK 0x3
+#define SCL_FREQ_OFS 0
+#define SCL_FREQ_MASK 0x3
+#define I2C_MST_DATA_WORD0 0x8
+#define I2C_MST_DATA_WORD1 0xc
+#define I2C_MST_DATA_WORD2 0x10
+#define I2C_MST_DATA_WORD3 0x14
+
+#define RTL9300_I2C_STD_FREQ 0
+#define RTL9300_I2C_FAST_FREQ 1
+
+DEFINE_MUTEX(i2c_lock);
+
+static int rtl9300_i2c_reg_addr_set(struct rtl9300_i2c *i2c, u32 reg, u16 len)
+{
+ u32 val, mask;
+ int ret;
+
+ val = len << MEM_ADDR_WIDTH_OFS;
+ mask = MEM_ADDR_WIDTH_MASK << MEM_ADDR_WIDTH_OFS;
+
+ ret = regmap_update_bits(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_CTRL2, mask, val);
+ if (ret)
+ return ret;
+
+ val = reg << MEM_ADDR_OFS;
+ mask = MEM_ADDR_MASK << MEM_ADDR_OFS;
+
+ ret = regmap_update_bits(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_CTRL1, mask, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl9300_i2c_config_io(struct rtl9300_i2c *i2c, u8 sda_pin)
+{
+ int ret;
+
+ ret = regmap_update_bits(i2c->regmap, i2c->i2c_mst_glb_ofs, BIT(sda_pin), BIT(sda_pin));
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_CTRL1,
+ (SDA_OUT_SEL_MASK << SDA_OUT_SEL_OFS) | GPIO_SCL_SEL,
+ (sda_pin << SDA_OUT_SEL_OFS) | GPIO_SCL_SEL);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl9300_i2c_config_xfer(struct rtl9300_i2c *i2c, u16 addr, u16 len)
+{
+ u32 val, mask;
+
+ val = i2c->bus_freq << SCL_FREQ_OFS;
+ mask = SCL_FREQ_MASK << SCL_FREQ_OFS;
+
+ val |= addr << DEV_ADDR_OFS;
+ mask |= DEV_ADDR_MASK << DEV_ADDR_OFS;
+
+ val |= ((len - 1) & 0xf) << DATA_WIDTH_OFS;
+ mask |= DATA_WIDTH_MASK << DATA_WIDTH_OFS;
+
+ mask |= RD_MODE;
+
+ return regmap_update_bits(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_CTRL2, mask, val);
+}
+
+static int rtl9300_i2c_read(struct rtl9300_i2c *i2c, u8 *buf, int len)
+{
+ u32 vals[4] = {};
+ int i, ret;
+
+ if (len > 16)
+ return -EIO;
+
+ ret = regmap_bulk_read(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_DATA_WORD0,
+ vals, ARRAY_SIZE(vals));
+ if (ret)
+ return ret;
+
+ for (i = 0; i < len; i++) {
+ buf[i] = vals[i/4] & 0xff;
+ vals[i/4] >>= 8;
+ }
+
+ return len;
+}
+
+static int rtl9300_i2c_write(struct rtl9300_i2c *i2c, u8 *buf, int len)
+{
+ u32 vals[4] = {};
+ int i, ret;
+
+ if (len > 16)
+ return -EIO;
+
+ for (i = 0; i < len; i++) {
+ if (i % 4 == 0)
+ vals[i/4] = 0;
+ vals[i/4] <<= 8;
+ vals[i/4] |= buf[i];
+ }
+
+ ret = regmap_bulk_write(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_DATA_WORD0,
+ vals, ARRAY_SIZE(vals));
+ if (ret)
+ return ret;
+
+ return len;
+}
+
+static int rtl9300_i2c_writel(struct rtl9300_i2c *i2c, u32 data)
+{
+ int ret;
+
+ ret = regmap_write(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_DATA_WORD0, data);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl9300_i2c_execute_xfer(struct rtl9300_i2c *i2c, char read_write,
+ int size, union i2c_smbus_data *data, int len)
+{
+ u32 val, mask;
+ int ret;
+
+ if (read_write == I2C_SMBUS_READ)
+ val = 0;
+ else
+ val = RWOP;
+ mask = RWOP;
+
+ val |= I2C_TRIG;
+ mask |= I2C_TRIG;
+
+ ret = regmap_update_bits(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_CTRL1, mask, val);
+ if (ret)
+ return ret;
+
+ ret = regmap_read_poll_timeout(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_CTRL1,
+ val, !(val & I2C_TRIG), 100, 2000);
+ if (ret)
+ return ret;
+
+ if (val & I2C_FAIL)
+ return -EIO;
+
+ if (read_write == I2C_SMBUS_READ) {
+ if (size == I2C_SMBUS_BYTE || size == I2C_SMBUS_BYTE_DATA) {
+ ret = regmap_read(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_DATA_WORD0, &val);
+ if (ret)
+ return ret;
+ data->byte = val & 0xff;
+ } else if (size == I2C_SMBUS_WORD_DATA) {
+ ret = regmap_read(i2c->regmap, i2c->i2c_mst_ofs + I2C_MST_DATA_WORD0, &val);
+ if (ret)
+ return ret;
+ data->word = val & 0xffff;
+ } else {
+ rtl9300_i2c_read(i2c, &data->block[0], len);
+ }
+ }
+
+ return 0;
+}
+
+static int rtl9300_i2c_smbus_xfer(struct i2c_adapter *adap, u16 addr,
+ unsigned short flags, char read_write,
+ u8 command, int size, union i2c_smbus_data *data)
+{
+ struct rtl9300_i2c *i2c = i2c_get_adapdata(adap);
+ int len = 0, ret;
+
+ mutex_lock(&i2c_lock);
+ switch (size) {
+ case I2C_SMBUS_QUICK:
+ rtl9300_i2c_config_xfer(i2c, addr, 0);
+ rtl9300_i2c_reg_addr_set(i2c, 0, 0);
+ break;
+
+ case I2C_SMBUS_BYTE:
+ if (read_write == I2C_SMBUS_WRITE) {
+ rtl9300_i2c_config_xfer(i2c, addr, 0);
+ rtl9300_i2c_reg_addr_set(i2c, command, 1);
+ } else {
+ rtl9300_i2c_config_xfer(i2c, addr, 1);
+ rtl9300_i2c_reg_addr_set(i2c, 0, 0);
+ }
+ break;
+
+ case I2C_SMBUS_BYTE_DATA:
+ rtl9300_i2c_reg_addr_set(i2c, command, 1);
+ rtl9300_i2c_config_xfer(i2c, addr, 1);
+ if (read_write == I2C_SMBUS_WRITE)
+ rtl9300_i2c_writel(i2c, data->byte);
+ break;
+
+ case I2C_SMBUS_WORD_DATA:
+ rtl9300_i2c_reg_addr_set(i2c, command, 1);
+ rtl9300_i2c_config_xfer(i2c, addr, 2);
+ if (read_write == I2C_SMBUS_WRITE)
+ rtl9300_i2c_writel(i2c, data->word);
+ break;
+
+ case I2C_SMBUS_BLOCK_DATA:
+ rtl9300_i2c_reg_addr_set(i2c, command, 1);
+ rtl9300_i2c_config_xfer(i2c, addr, data->block[0]);
+ if (read_write == I2C_SMBUS_WRITE)
+ rtl9300_i2c_write(i2c, &data->block[1], data->block[0]);
+ len = data->block[0];
+ break;
+
+ default:
+ dev_warn(&adap->dev, "Unsupported transaction %d\n", size);
+ ret = -EOPNOTSUPP;
+ goto out_unlock;
+ }
+
+ ret = rtl9300_i2c_execute_xfer(i2c, read_write, size, data, len);
+
+out_unlock:
+ mutex_unlock(&i2c_lock);
+
+ return ret;
+}
+
+static u32 rtl9300_i2c_func(struct i2c_adapter *a)
+{
+ return I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE |
+ I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA |
+ I2C_FUNC_SMBUS_BLOCK_DATA;
+}
+
+static const struct i2c_algorithm rtl9300_i2c_algo = {
+ .smbus_xfer = rtl9300_i2c_smbus_xfer,
+ .functionality = rtl9300_i2c_func,
+};
+
+struct i2c_adapter_quirks rtl9300_i2c_quirks = {
+ .flags = I2C_AQ_NO_CLK_STRETCH,
+ .max_read_len = 16,
+ .max_write_len = 16,
+};
+
+static int rtl9300_i2c_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct rtl9300_i2c *i2c;
+ struct i2c_adapter *adap;
+ u32 clock_freq, sda_pin;
+ int ret;
+
+ i2c = devm_kzalloc(dev, sizeof(*i2c), GFP_KERNEL);
+ if (!i2c)
+ return -ENOMEM;
+
+ i2c->regmap = syscon_node_to_regmap(dev->parent->of_node);
+ if (IS_ERR(i2c->regmap))
+ return PTR_ERR(i2c->regmap);
+ i2c->dev = dev;
+
+ ret = device_property_read_u32(dev, "realtek,control-offset", &i2c->i2c_mst_ofs);
+ if (ret)
+ return ret;
+
+ ret = device_property_read_u32(dev, "realtek,global-control-offset", &i2c->i2c_mst_glb_ofs);
+ if (ret)
+ return ret;
+
+ ret = device_property_read_u32(dev, "clock-frequency", &clock_freq);
+ if (ret)
+ clock_freq = I2C_MAX_STANDARD_MODE_FREQ;
+
+ switch (clock_freq) {
+ case I2C_MAX_STANDARD_MODE_FREQ:
+ i2c->bus_freq = RTL9300_I2C_STD_FREQ;
+ break;
+
+ case I2C_MAX_FAST_MODE_FREQ:
+ i2c->bus_freq = RTL9300_I2C_FAST_FREQ;
+ break;
+ default:
+ dev_warn(i2c->dev, "clock-frequency %d not supported\n", clock_freq);
+ return -EINVAL;
+ }
+
+ ret = device_property_read_u32(dev, "realtek,sda-pin", &sda_pin);
+ if (ret)
+ sda_pin = 0;
+ i2c->sda_pin = sda_pin;
+
+ adap = &i2c->adap;
+ adap->owner = THIS_MODULE;
+ adap->algo = &rtl9300_i2c_algo;
+ adap->quirks = &rtl9300_i2c_quirks;
+ adap->retries = 3;
+ adap->dev.parent = dev;
+ i2c_set_adapdata(adap, i2c);
+ adap->dev.of_node = dev->of_node;
+ strscpy(adap->name, dev_name(dev), sizeof(adap->name));
+
+ platform_set_drvdata(pdev, i2c);
+
+ ret = rtl9300_i2c_config_io(i2c, i2c->sda_pin);
+ if (ret)
+ return ret;
+
+ return i2c_add_adapter(adap);
+}
+
+static void rtl9300_i2c_remove(struct platform_device *pdev)
+{
+ struct rtl9300_i2c *i2c = platform_get_drvdata(pdev);
+
+ i2c_del_adapter(&i2c->adap);
+}
+
+static const struct of_device_id i2c_rtl9300_dt_ids[] = {
+ { .compatible = "realtek,rtl9300-i2c" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, i2c_rtl9300_dt_ids);
+
+static struct platform_driver rtl9300_i2c_driver = {
+ .probe = rtl9300_i2c_probe,
+ .remove = rtl9300_i2c_remove,
+ .driver = {
+ .name = "i2c-rtl9300",
+ .of_match_table = i2c_rtl9300_dt_ids,
+ },
+};
+
+module_platform_driver(rtl9300_i2c_driver);
+
+MODULE_DESCRIPTION("RTL9300 I2C controller driver");
+MODULE_LICENSE("GPL");
+
Add support for the I2C controller on the RTL9300 SoC. This is based on the openwrt implementation[1] but cleaned up to make use of the regmap APIs. [1] - https://git.openwrt.org/?p=openwrt/openwrt.git;a=blob;f=target/linux/realtek/files-5.15/drivers/i2c/busses/i2c-rtl9300.c Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> --- MAINTAINERS | 1 + drivers/i2c/busses/Kconfig | 10 + drivers/i2c/busses/Makefile | 1 + drivers/i2c/busses/i2c-rtl9300.c | 377 +++++++++++++++++++++++++++++++ 4 files changed, 389 insertions(+) create mode 100644 drivers/i2c/busses/i2c-rtl9300.c