| Message ID | 20220206115939.3091265-5-luca@lucaceresoli.net |
|---|---|
| State | New |
| Headers | show |
| Series | Hi, | expand |
On Sun, Feb 06, 2022 at 12:59:37PM +0100, Luca Ceresoli wrote: > Describe the Texas Instruments DS90UB954-Q1, a 2-input MIPI CSI-2 video > deserializer with I2C Address Translator and remote GPIOs. > > Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> > > --- > > Changes RFCv2 -> RFCv3: > > - rewrite in yaml > - use new layout based on remote-chips under the main deser node > - new clock configuration based on common clock framework > > Changes RFCv1 -> RFCv2: > > - add explicit aliases for the FPD-link RX ports (optional) > - add proper remote GPIO description > --- > .../bindings/media/i2c/ti,ds90ub954-q1.yaml | 235 ++++++++++++++++++ > MAINTAINERS | 6 + > 2 files changed, 241 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml > > diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml > new file mode 100644 > index 000000000000..95dc3d22f5d8 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml > @@ -0,0 +1,235 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +# Copyright (C) 2019 Renesas Electronics Corp. > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub954-q1.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Texas Instruments DS90UB954-Q1 dual video deserializer > + > +maintainers: > + - Luca Ceresoli <luca@lucaceresoli.net> > + > +description: | > + The TI DS90UB954-Q1 is a MIPI CSI-2 video deserializer that forwards > + video streams from up to two FPD-Link 3 connections to a MIPI CSI-2 > + output. It also allows access to remote I2C and GPIO. > + > +properties: > + compatible: > + const: ti,ds90ub954-q1 > + > + reg: > + description: | > + main I2C slave address; optionally aliases for RX port registers and > + remote serializers. The main address is mandatory and must be the > + first, others are optional and fall back to defaults if not > + specified. See "reg-names". minItems: 1 maxItems: 5 > + > + reg-names: > + description: | > + Names of I2C address used to communicate with the chip, must match > + the "reg" values; mandatory if there are 2 or more addresses. > + "main" is the main I2C address, used to access shared registers. > + "rxport0" and "rxport1" are the I2C alias to access FPD-link RX > + port specific registers; must not be used by other slaves on the > + same bus. "ser0" and "ser1" are the I2C alias to access the remote > + serializer connected on each FPD-link RX port; must not be used by > + other slaves on the same bus. > + minItems: 1 > + maxItems: 5 > + items: > + - const: main > + - const: rxport0 > + - const: rxport1 > + - const: ser0 > + - const: ser1 > + > + clocks: > + description: provider of the clock on the XIN/REFCLK pin > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + reset-gpios: > + description: chip reset GPIO connected to PDB pin (active low) maxItems: 1 > + > + i2c-alias-pool: Needs a type. > + description: | > + list of I2C addresses that are known to be available on the "local" > + (SoC-to-deser) I2C bus; they will be picked at runtime and used as > + aliases to reach remote I2C chips > + > + '#clock-cells': > + description: | > + the DS90UB954 provides the FPD line rate clock to the serializer > + const: 0 > + > + ports: > + $ref: /schemas/graph.yaml#/properties/ports > + > + patternProperties: > + '^port@[01]$': > + $ref: /schemas/graph.yaml#/$defs/port-base > + description: FPD-Link RX port 0 (RIN0+/RIN0- pins) > + > + properties: > + endpoint: > + $ref: /schemas/media/video-interfaces.yaml# > + unevaluatedProperties: false > + > + '^port@2$': > + $ref: /schemas/graph.yaml#/properties/port > + description: MIPI-CSI2 TX port > + > + remote-chips: > + type: object > + > + properties: > + '#address-cells': > + const: 1 > + '#size-cells': > + const: 0 > + > + patternProperties: > + '^remote-chip@([01]+)$': > + type: object > + $ref: /schemas/media/i2c/ti,ds90ub953-q1.yaml# > + > + required: > + - '#address-cells' > + - '#size-cells' > + > + additionalProperties: false > + > + i2c-atr: > + description: | > + Each child describes the I2C bus on the remote side of an RX port > + type: object > + > + properties: > + '#address-cells': > + const: 1 > + '#size-cells': > + const: 0 > + > + patternProperties: > + '^i2c@([01]+)$': Only 0 or 1 is valid? Then drop the '+'. This is an i2c bus, so you need: $ref: /schemas/i2c-controller.yaml#' unevaluatedProperties: false > + type: object > + > + properties: > + reg: > + maxItems: 1 > + '#address-cells': > + const: 1 > + '#size-cells': > + const: 0 You can drop these as i2c-controller.yaml covers them. > + clock-frequency: > + minimum: 1 1 is already the minimum. (Well, maybe it is 0, but that's not really useful.) > + maximum: 1000000 > + > + additionalProperties: false > + > +required: > + - compatible > + - reg > + - clocks > + - ports > + - remote-chips > + - i2c-atr > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/irq.h> > + #include <dt-bindings/gpio/gpio.h> > + #include <dt-bindings/media/ds90ub953.h> > + > + i2c@0 { > + reg = <0x0 0x100>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + deser: deser@3d { > + compatible = "ti,ds90ub954-q1"; > + reg-names = "main", "rxport0", "rxport1", "ser0", "ser1"; > + reg = <0x3d>, <0x40>, <0x41>, <0x44>, <0x45>; > + clocks = <&clk_25M>; > + interrupt-parent = <&gic>; > + interrupts = <3 1 IRQ_TYPE_LEVEL_LOW>; > + reset-gpios = <&gpio 4 GPIO_ACTIVE_LOW>; > + > + #clock-cells = <0>; > + > + i2c-alias-pool = /bits/ 16 <0x4a 0x4b 0x4c 0x4d 0x4e 0x4f>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + ds90ub954_fpd3_in0: endpoint { > + remote-endpoint = <&sensor_0_out>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + ds90ub954_mipi_out0: endpoint { > + data-lanes = <1 2 3 4>; > + link-frequencies = /bits/ 64 <400000000>; > + remote-endpoint = <&csirx_0_in>; > + }; > + }; > + }; > + > + remote-chips { > + #address-cells = <1>; > + #size-cells = <0>; > + > + des0_ser0: remote-chip@0 { > + reg = <0>; > + compatible = "ti,ds90ub953-q1"; > + clocks = <&deser>; > + ti,gpio-functions = > + <DS90_GPIO_FUNC_UNUSED > + DS90_GPIO_FUNC_OUTPUT_REMOTE > + DS90_GPIO_FUNC_UNUSED > + DS90_GPIO_FUNC_UNUSED>; > + > + gpio-controller; > + #gpio-cells = <2>; > + #clock-cells = <0>; > + }; > + }; > + > + i2c-atr { > + #address-cells = <1>; > + #size-cells = <0>; > + > + remote_i2c0: i2c@0 { > + reg = <0>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + sensor_0@1a { > + compatible = "sony,imx274"; > + reg = <0x1a>; > + > + reset-gpios = <&des0_ser0 1 GPIO_ACTIVE_LOW>; > + > + port { > + sensor_0_out: endpoint { > + remote-endpoint = <&ds90ub954_fpd3_in0>; > + }; > + }; > + }; > + }; > + }; > + }; > + }; > + > +... > diff --git a/MAINTAINERS b/MAINTAINERS > index 4429ce035496..f0156062f788 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -19097,6 +19097,12 @@ S: Maintained > F: Documentation/devicetree/bindings/media/i2c/ti,ds90ub953-q1.yaml > F: include/dt-bindings/media/ds90ub953.h > > +TEXAS INSTRUMENTS DS90UB954 VIDEO DESERIALIZER DRIVER > +M: Luca Ceresoli <luca@lucaceresoli.net> > +L: linux-media@vger.kernel.org > +S: Maintained > +F: Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml > + > TEXAS INSTRUMENTS' SYSTEM CONTROL INTERFACE (TISCI) PROTOCOL DRIVER > M: Nishanth Menon <nm@ti.com> > M: Tero Kristo <kristo@kernel.org> > -- > 2.25.1 > >
diff --git a/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml new file mode 100644 index 000000000000..95dc3d22f5d8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml @@ -0,0 +1,235 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/ti,ds90ub954-q1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DS90UB954-Q1 dual video deserializer + +maintainers: + - Luca Ceresoli <luca@lucaceresoli.net> + +description: | + The TI DS90UB954-Q1 is a MIPI CSI-2 video deserializer that forwards + video streams from up to two FPD-Link 3 connections to a MIPI CSI-2 + output. It also allows access to remote I2C and GPIO. + +properties: + compatible: + const: ti,ds90ub954-q1 + + reg: + description: | + main I2C slave address; optionally aliases for RX port registers and + remote serializers. The main address is mandatory and must be the + first, others are optional and fall back to defaults if not + specified. See "reg-names". + + reg-names: + description: | + Names of I2C address used to communicate with the chip, must match + the "reg" values; mandatory if there are 2 or more addresses. + "main" is the main I2C address, used to access shared registers. + "rxport0" and "rxport1" are the I2C alias to access FPD-link RX + port specific registers; must not be used by other slaves on the + same bus. "ser0" and "ser1" are the I2C alias to access the remote + serializer connected on each FPD-link RX port; must not be used by + other slaves on the same bus. + minItems: 1 + maxItems: 5 + items: + - const: main + - const: rxport0 + - const: rxport1 + - const: ser0 + - const: ser1 + + clocks: + description: provider of the clock on the XIN/REFCLK pin + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + description: chip reset GPIO connected to PDB pin (active low) + + i2c-alias-pool: + description: | + list of I2C addresses that are known to be available on the "local" + (SoC-to-deser) I2C bus; they will be picked at runtime and used as + aliases to reach remote I2C chips + + '#clock-cells': + description: | + the DS90UB954 provides the FPD line rate clock to the serializer + const: 0 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + patternProperties: + '^port@[01]$': + $ref: /schemas/graph.yaml#/$defs/port-base + description: FPD-Link RX port 0 (RIN0+/RIN0- pins) + + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + '^port@2$': + $ref: /schemas/graph.yaml#/properties/port + description: MIPI-CSI2 TX port + + remote-chips: + type: object + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + '^remote-chip@([01]+)$': + type: object + $ref: /schemas/media/i2c/ti,ds90ub953-q1.yaml# + + required: + - '#address-cells' + - '#size-cells' + + additionalProperties: false + + i2c-atr: + description: | + Each child describes the I2C bus on the remote side of an RX port + type: object + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + '^i2c@([01]+)$': + type: object + + properties: + reg: + maxItems: 1 + '#address-cells': + const: 1 + '#size-cells': + const: 0 + clock-frequency: + minimum: 1 + maximum: 1000000 + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - ports + - remote-chips + - i2c-atr + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/media/ds90ub953.h> + + i2c@0 { + reg = <0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + + deser: deser@3d { + compatible = "ti,ds90ub954-q1"; + reg-names = "main", "rxport0", "rxport1", "ser0", "ser1"; + reg = <0x3d>, <0x40>, <0x41>, <0x44>, <0x45>; + clocks = <&clk_25M>; + interrupt-parent = <&gic>; + interrupts = <3 1 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + + #clock-cells = <0>; + + i2c-alias-pool = /bits/ 16 <0x4a 0x4b 0x4c 0x4d 0x4e 0x4f>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ds90ub954_fpd3_in0: endpoint { + remote-endpoint = <&sensor_0_out>; + }; + }; + + port@2 { + reg = <2>; + ds90ub954_mipi_out0: endpoint { + data-lanes = <1 2 3 4>; + link-frequencies = /bits/ 64 <400000000>; + remote-endpoint = <&csirx_0_in>; + }; + }; + }; + + remote-chips { + #address-cells = <1>; + #size-cells = <0>; + + des0_ser0: remote-chip@0 { + reg = <0>; + compatible = "ti,ds90ub953-q1"; + clocks = <&deser>; + ti,gpio-functions = + <DS90_GPIO_FUNC_UNUSED + DS90_GPIO_FUNC_OUTPUT_REMOTE + DS90_GPIO_FUNC_UNUSED + DS90_GPIO_FUNC_UNUSED>; + + gpio-controller; + #gpio-cells = <2>; + #clock-cells = <0>; + }; + }; + + i2c-atr { + #address-cells = <1>; + #size-cells = <0>; + + remote_i2c0: i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + sensor_0@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + + reset-gpios = <&des0_ser0 1 GPIO_ACTIVE_LOW>; + + port { + sensor_0_out: endpoint { + remote-endpoint = <&ds90ub954_fpd3_in0>; + }; + }; + }; + }; + }; + }; + }; + +... diff --git a/MAINTAINERS b/MAINTAINERS index 4429ce035496..f0156062f788 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -19097,6 +19097,12 @@ S: Maintained F: Documentation/devicetree/bindings/media/i2c/ti,ds90ub953-q1.yaml F: include/dt-bindings/media/ds90ub953.h +TEXAS INSTRUMENTS DS90UB954 VIDEO DESERIALIZER DRIVER +M: Luca Ceresoli <luca@lucaceresoli.net> +L: linux-media@vger.kernel.org +S: Maintained +F: Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml + TEXAS INSTRUMENTS' SYSTEM CONTROL INTERFACE (TISCI) PROTOCOL DRIVER M: Nishanth Menon <nm@ti.com> M: Tero Kristo <kristo@kernel.org>
Describe the Texas Instruments DS90UB954-Q1, a 2-input MIPI CSI-2 video deserializer with I2C Address Translator and remote GPIOs. Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> --- Changes RFCv2 -> RFCv3: - rewrite in yaml - use new layout based on remote-chips under the main deser node - new clock configuration based on common clock framework Changes RFCv1 -> RFCv2: - add explicit aliases for the FPD-link RX ports (optional) - add proper remote GPIO description --- .../bindings/media/i2c/ti,ds90ub954-q1.yaml | 235 ++++++++++++++++++ MAINTAINERS | 6 + 2 files changed, 241 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,ds90ub954-q1.yaml