@@ -165,20 +165,21 @@ static int mtk_pinconf_get(struct pinctrl_dev *pctldev,
err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_SR, &ret);
break;
case PIN_CONFIG_INPUT_ENABLE:
- case PIN_CONFIG_OUTPUT_ENABLE:
+ err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_IES, &ret);
+ if (!ret)
+ err = -EINVAL;
+ break;
+ case PIN_CONFIG_OUTPUT:
err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DIR, &ret);
if (err)
break;
- /* CONFIG Current direction return value
- * ------------- ----------------- ----------------------
- * OUTPUT_ENABLE output 1 (= HW value)
- * input 0 (= HW value)
- * INPUT_ENABLE output 0 (= reverse HW value)
- * input 1 (= reverse HW value)
- */
- if (param == PIN_CONFIG_INPUT_ENABLE)
- ret = !ret;
+ if (!ret) {
+ err = -EINVAL;
+ break;
+ }
+
+ err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DO, &ret);
break;
case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
err = mtk_hw_get_value(hw, desc, PINCTRL_PIN_REG_DIR, &ret);
@@ -283,26 +284,9 @@ static int mtk_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin,
break;
err = hw->soc->bias_set_combo(hw, desc, 0, arg);
break;
- case PIN_CONFIG_OUTPUT_ENABLE:
- err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_SMT,
- MTK_DISABLE);
- /* Keep set direction to consider the case that a GPIO pin
- * does not have SMT control
- */
- if (err != -ENOTSUPP)
- break;
-
- err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR,
- MTK_OUTPUT);
- break;
case PIN_CONFIG_INPUT_ENABLE:
/* regard all non-zero value as enable */
err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_IES, !!arg);
- if (err)
- break;
-
- err = mtk_hw_set_value(hw, desc, PINCTRL_PIN_REG_DIR,
- MTK_INPUT);
break;
case PIN_CONFIG_SLEW_RATE:
/* regard all non-zero value as enable */
There is a misinterpretation of some of the PIN_CONFIG_* options in this driver library. PIN_CONFIG_OUTPUT_ENABLE should refer to a buffer or switch in the output direction of the electrical path. The MediaTek hardware does not have such a thing. The driver incorrectly maps this option to the GPIO function's direction. Likewise, PIN_CONFIG_INPUT_ENABLE should refer to a buffer or switch in the input direction. The hardware does have such a mechanism, and is mapped to the IES bit. The driver however sets the direction in addition to the IES bit, which is incorrect. On readback, the IES bit isn't even considered. Ironically, the driver does not support readback for PIN_CONFIG_OUTPUT, while its readback of PIN_CONFIG_{INPUT,OUTPUT}_ENABLE is what it should be doing for PIN_CONFIG_OUTPUT. Rework support for these three options, so that PIN_CONFIG_OUTPUT_ENABLE is completely removed, PIN_CONFIG_INPUT_ENABLE is only linked to the IES bit, and PIN_CONFIG_OUTPUT is linked to the GPIO function's direction and output level. Fixes: 805250982bb5 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> --- drivers/pinctrl/mediatek/pinctrl-paris.c | 38 +++++++----------------- 1 file changed, 11 insertions(+), 27 deletions(-)