@@ -2104,6 +2104,18 @@ config MFD_QCOM_PM8008
under it in the device tree. Additional drivers must be enabled in
order to use the functionality of the device.
+config MFD_INTEL_UPBOARD_FPGA
+ tristate "Support for the Intel platform foundation kit UP board FPGA"
+ select MFD_CORE
+ depends on X86 && ACPI
+ help
+ Select this option to enable the Intel AAEON UP and UP^2 on-board FPGA.
+ This is core driver for the UP board that implements certain (pin
+ control, onboard LEDs or CEC) through an on-board FPGA.
+
+ To compile this driver as a module, choose M here: the module will be
+ called upboard-fpga.
+
menu "Multimedia Capabilities Port drivers"
depends on ARCH_SA1100
@@ -250,6 +250,7 @@ obj-$(CONFIG_MFD_ALTERA_A10SR) += altera-a10sr.o
obj-$(CONFIG_MFD_ALTERA_SYSMGR) += altera-sysmgr.o
obj-$(CONFIG_MFD_STPMIC1) += stpmic1.o
obj-$(CONFIG_MFD_SUN4I_GPADC) += sun4i-gpadc.o
+obj-$(CONFIG_MFD_INTEL_UPBOARD_FPGA) += upboard-fpga.o
obj-$(CONFIG_MFD_STM32_LPTIMER) += stm32-lptimer.o
obj-$(CONFIG_MFD_STM32_TIMERS) += stm32-timers.o
new file mode 100644
@@ -0,0 +1,526 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * UP Board multi function device driver for control CPLD/FPGA to
+ * provide more GPIO driving power also provide CPLD LEDs and pin mux function
+ * recognize HID AANT0F00 ~ AAANT0F04 in ACPI name space
+ *
+ * Copyright (c) AAEON. All rights reserved.
+ *
+ * Author: Gary Wang <garywang@aaeon.com.tw>
+ *
+ */
+#include <linux/acpi.h>
+#include <linux/dmi.h>
+#include <linux/gpio/consumer.h>
+#include <linux/kernel.h>
+#include <linux/leds.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/upboard-fpga.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/bits.h>
+#include <linux/err.h>
+
+struct upboard_fpga_data {
+ const struct regmap_config *cpld_config;
+ const struct mfd_cell *cells;
+ size_t ncells;
+};
+
+#define AAEON_MANUFACTURER_ID 0x01
+#define SUPPORTED_FW_MAJOR 0x0
+#define MENUFACTURER_ID_MASK GENMASK(7, 0)
+
+#define FIRMWARE_ID_BUILD_OFFSET (12)
+#define FIRMWARE_ID_MAJOR_OFFSET (8)
+#define FIRMWARE_ID_MINOR_OFFSET (4)
+#define FIRMWARE_ID_PATCH_OFFSET (0)
+#define FIRMWARE_ID_MASK GENMASK(3, 0)
+
+/*
+ * For UP Board Series FPGA register read/write protocols
+ * EMUTEX specs:
+ * D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 .... D22 D23
+ * [RW][ address ][ DATA ]
+ *
+ * Read Sequence:
+ * ___ ____________________________________________________ _________
+ * clr: \_/ <--low-pulse does start the write-readback \_/<--start
+ * sequence with partital reset of internal new sequence
+ * registers but the CONF-REG.
+ * ____________________________________________________________________
+ * rst: _/ _ _ _ _ _ _ __ __ __ _
+ * stb: STB#1->_/1\_/2\_/3\_...._/7\_/8\_/9\_/10\_..../23\_/24\_/<-STB#25 edge
+ * is needed
+ * to ACK
+ * (D0 - D7 stb rising latch)
+ * data_in: D0 D1 D2 .... D6 D7 don't ........ care(DC)
+ * data_out: don't ...........care(DC) D8 D9 .... D22 D23
+ * (D8 - D23 stb falling latch)
+ * flag_Read: _________...._________
+ * __DC_ ____________...._________/ \_
+ * counter:
+ * [00]DC[00][01][02] ............[08][9][10]............[24][00]
+ * CONF-REG:
+ * [00] [ CONF-REG ]
+ * wreg:
+ * [00]DC[00][ wreg=SHFT(wreg) ][ADR][DATA][wreg=SHFT(wreg)]
+ * wreg2:
+ * [ (COPY)=ADDR ]
+ */
+static int upboard_fpga_read(void *context, unsigned int reg, unsigned int *val)
+{
+ struct upboard_fpga * const fpga = context;
+ int i;
+
+ gpiod_set_value(fpga->clear_gpio, 0);
+ gpiod_set_value(fpga->clear_gpio, 1);
+
+ reg |= UPFPGA_READ_FLAG;
+
+ for (i = UPFPGA_ADDRESS_SIZE; i >= 0; i--) {
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ gpiod_set_value(fpga->datain_gpio, !!(reg & BIT(i)));
+ gpiod_set_value(fpga->strobe_gpio, 1);
+ }
+
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ *val = 0;
+
+ for (i = UPFPGA_REGISTER_SIZE - 1; i >= 0; i--) {
+ gpiod_set_value(fpga->strobe_gpio, 1);
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ *val |= gpiod_get_value(fpga->dataout_gpio) << i;
+ }
+
+ gpiod_set_value(fpga->strobe_gpio, 1);
+
+ return 0;
+}
+
+/*
+ * Write Sequence:
+ * ___ ____________________________________________________ _________
+ * clr: \_/ <--low-pulse does start the write-readback \_/<--start
+ * sequence with partital reset of internal new sequence
+ * registers but the CONF-REG.
+ * ____________________________________________________________________
+ * rst: _/ _ _ _ _ _ _ __ __ __ _
+ * stb: STB#1->_/1\_/2\_/3\_...._/7\_/8\_/9\_/10\_..../23\_/24\_/<-STB#25 edge
+ * is needed
+ * to ACK
+ * (D0 - D23 stb rising latch)
+ * data_in: D0 D1 D2 .... D6 D7 D8 D9 .... D22 D23
+ * data_out: don't ................................care (DC)
+ * flag_Read:
+ * __DC_ ____________....__________________________________
+ * counter:
+ * [00]DC[00][01][02] ............[08][9][10]............[24][00]
+ * wreg:
+ * [00]DC[00][wreg=SHFT(wreg)&dat_in ][SHFT(wreg)&dat_in][DAT]
+ * wreg2:
+ * [ (COPY)=ADDR ]
+ * CONF-REG:
+ * [00] [ CONF-REG = OLD VALUE ][CONF-REG=DAT]
+ */
+static int upboard_fpga_write(void *context, unsigned int reg, unsigned int val)
+{
+ struct upboard_fpga * const fpga = context;
+ int i;
+
+ gpiod_set_value(fpga->clear_gpio, 0);
+ gpiod_set_value(fpga->clear_gpio, 1);
+
+ for (i = UPFPGA_ADDRESS_SIZE; i >= 0; i--) {
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ gpiod_set_value(fpga->datain_gpio, !!(reg & BIT(i)));
+ gpiod_set_value(fpga->strobe_gpio, 1);
+ }
+
+ gpiod_set_value(fpga->strobe_gpio, 0);
+
+ for (i = UPFPGA_REGISTER_SIZE - 1; i >= 0; i--) {
+ gpiod_set_value(fpga->datain_gpio, !!(val & BIT(i)));
+ gpiod_set_value(fpga->strobe_gpio, 1);
+ gpiod_set_value(fpga->strobe_gpio, 0);
+ }
+
+ gpiod_set_value(fpga->strobe_gpio, 1);
+
+ return 0;
+}
+
+static const struct regmap_range upboard_up_readable_ranges[] = {
+ regmap_reg_range(UPFPGA_REG_PLATFORM_ID, UPFPGA_REG_FIRMWARE_ID),
+ regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN0),
+ regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR1),
+};
+
+static const struct regmap_range upboard_up_writable_ranges[] = {
+ regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN0),
+ regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR1),
+};
+
+static const struct regmap_access_table upboard_up_readable_table = {
+ .yes_ranges = upboard_up_readable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up_readable_ranges),
+};
+
+static const struct regmap_access_table upboard_up_writable_table = {
+ .yes_ranges = upboard_up_writable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up_writable_ranges),
+};
+
+static const struct regmap_config upboard_up_regmap_config = {
+ .reg_bits = UPFPGA_ADDRESS_SIZE,
+ .val_bits = UPFPGA_REGISTER_SIZE,
+ .max_register = UPFPGA_REG_MAX,
+ .reg_read = upboard_fpga_read,
+ .reg_write = upboard_fpga_write,
+ .fast_io = false,
+ .cache_type = REGCACHE_RBTREE,
+ .rd_table = &upboard_up_readable_table,
+ .wr_table = &upboard_up_writable_table,
+};
+
+static struct upboard_led_data upboard_up_led_data[] = {
+ { .bit = 0, .colour = "yellow" },
+ { .bit = 1, .colour = "green" },
+ { .bit = 2, .colour = "red" },
+};
+
+static const struct mfd_cell upboard_up_mfd_cells[] = {
+ { .name = "upboard-pinctrl" },
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up_led_data[0],
+ sizeof(*upboard_up_led_data), 0),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up_led_data[1],
+ sizeof(*upboard_up_led_data), 1),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up_led_data[2],
+ sizeof(*upboard_up_led_data), 2),
+};
+
+/* UP Squared 6000 EHL board */
+
+static const struct upboard_fpga_data upboard_up_fpga_data = {
+ .cpld_config = &upboard_up_regmap_config,
+ .cells = upboard_up_mfd_cells,
+ .ncells = ARRAY_SIZE(upboard_up_mfd_cells),
+};
+
+static const struct mfd_cell upboard_pinctrl_cells[] = {
+ { .name = "upboard-pinctrl" },
+};
+
+static const struct upboard_fpga_data upboard_pinctrl_data = {
+ .cpld_config = &upboard_up_regmap_config,
+ .cells = upboard_pinctrl_cells,
+ .ncells = ARRAY_SIZE(upboard_pinctrl_cells),
+};
+
+/* UP^2 board */
+static const struct regmap_range upboard_up2_readable_ranges[] = {
+ regmap_reg_range(UPFPGA_REG_PLATFORM_ID, UPFPGA_REG_FIRMWARE_ID),
+ regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN1),
+ regmap_reg_range(UPFPGA_REG_GPIO_EN0, UPFPGA_REG_GPIO_EN2),
+ regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR2),
+};
+
+static const struct regmap_range upboard_up2_writable_ranges[] = {
+ regmap_reg_range(UPFPGA_REG_FUNC_EN0, UPFPGA_REG_FUNC_EN1),
+ regmap_reg_range(UPFPGA_REG_GPIO_EN0, UPFPGA_REG_GPIO_EN2),
+ regmap_reg_range(UPFPGA_REG_GPIO_DIR0, UPFPGA_REG_GPIO_DIR2),
+};
+
+static const struct regmap_access_table upboard_up2_readable_table = {
+ .yes_ranges = upboard_up2_readable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up2_readable_ranges),
+};
+
+static const struct regmap_access_table upboard_up2_writable_table = {
+ .yes_ranges = upboard_up2_writable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(upboard_up2_writable_ranges),
+};
+
+static const struct regmap_config upboard_up2_regmap_config = {
+ .reg_bits = UPFPGA_ADDRESS_SIZE,
+ .val_bits = UPFPGA_REGISTER_SIZE,
+ .max_register = UPFPGA_REG_MAX,
+ .reg_read = upboard_fpga_read,
+ .reg_write = upboard_fpga_write,
+ .fast_io = false,
+ .cache_type = REGCACHE_NONE,
+ .rd_table = &upboard_up2_readable_table,
+ .wr_table = &upboard_up2_writable_table,
+};
+
+static struct upboard_led_data upboard_up2_led_data[] = {
+ { .bit = 0, .colour = "blue" },
+ { .bit = 1, .colour = "yellow" },
+ { .bit = 2, .colour = "green" },
+ { .bit = 3, .colour = "red" },
+};
+
+static const struct mfd_cell upboard_up2_mfd_cells[] = {
+ { .name = "upboard-pinctrl" },
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[0],
+ sizeof(*upboard_up2_led_data), 0),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[1],
+ sizeof(*upboard_up2_led_data), 1),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[2],
+ sizeof(*upboard_up2_led_data), 2),
+ MFD_CELL_BASIC("upboard-led", NULL, &upboard_up2_led_data[3],
+ sizeof(*upboard_up2_led_data), 3),
+};
+
+static const struct upboard_fpga_data upboard_up2_fpga_data = {
+ .cpld_config = &upboard_up2_regmap_config,
+ .cells = upboard_up2_mfd_cells,
+ .ncells = ARRAY_SIZE(upboard_up2_mfd_cells),
+};
+
+/* UP-CRST02 carrier board for UP Core */
+
+/* same MAX10 config as UP2, but same LED cells as UP1 */
+static const struct upboard_fpga_data upboard_upcore_crst02_fpga_data = {
+ .cpld_config = &upboard_up2_regmap_config,
+ .cells = upboard_up_mfd_cells,
+ .ncells = ARRAY_SIZE(upboard_up_mfd_cells),
+};
+
+static int __init upboard_fpga_gpio_init(struct upboard_fpga *fpga)
+{
+ enum gpiod_flags flags = fpga->uninitialised ? GPIOD_OUT_LOW : GPIOD_ASIS;
+
+ fpga->enable_gpio = devm_gpiod_get(fpga->dev, "enable", flags);
+ if (IS_ERR(fpga->enable_gpio))
+ return PTR_ERR(fpga->enable_gpio);
+
+ fpga->clear_gpio = devm_gpiod_get(fpga->dev, "clear", GPIOD_OUT_LOW);
+ if (IS_ERR(fpga->clear_gpio))
+ return PTR_ERR(fpga->clear_gpio);
+
+ fpga->strobe_gpio = devm_gpiod_get(fpga->dev, "strobe", GPIOD_OUT_LOW);
+ if (IS_ERR(fpga->strobe_gpio))
+ return PTR_ERR(fpga->strobe_gpio);
+
+ fpga->datain_gpio = devm_gpiod_get(fpga->dev, "datain", GPIOD_OUT_LOW);
+ if (IS_ERR(fpga->datain_gpio))
+ return PTR_ERR(fpga->datain_gpio);
+
+ fpga->dataout_gpio = devm_gpiod_get(fpga->dev, "dataout", GPIOD_IN);
+ if (IS_ERR(fpga->dataout_gpio))
+ return PTR_ERR(fpga->dataout_gpio);
+
+ /*
+ * The SoC pinctrl driver may not support reserving the GPIO line for
+ * FPGA reset without causing an undesired reset pulse. This will clear
+ * any settings on the FPGA, so only do it if we must.
+ * Reset GPIO defaults HIGH, get GPIO and set to LOW, then set back to
+ * HIGH as a pulse.
+ */
+ if (fpga->uninitialised) {
+ fpga->reset_gpio = devm_gpiod_get(fpga->dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(fpga->reset_gpio))
+ return PTR_ERR(fpga->reset_gpio);
+
+ gpiod_set_value(fpga->reset_gpio, 1);
+ }
+
+ gpiod_set_value(fpga->enable_gpio, 1);
+ fpga->uninitialised = false;
+
+ return 0;
+}
+
+/*
+ * This function is for debugging with user for showing firmware information.
+ */
+static int __init upboard_fpga_show_firmware_info(struct upboard_fpga *fpga)
+{
+ unsigned int platform_id, manufacturer_id;
+ unsigned int firmware_id, build, major, minor, patch;
+ int ret;
+
+ if (!fpga)
+ return -ENOMEM;
+
+ ret = regmap_read(fpga->regmap, UPFPGA_REG_PLATFORM_ID, &platform_id);
+ if (ret)
+ return ret;
+
+ manufacturer_id = platform_id & MENUFACTURER_ID_MASK;
+ if (manufacturer_id != AAEON_MANUFACTURER_ID) {
+ dev_err(fpga->dev,
+ "driver not compatible with custom FPGA FW from manufacturer id 0x%02x. Exiting",
+ manufacturer_id);
+
+ return -ENODEV;
+ }
+
+ ret = regmap_read(fpga->regmap, UPFPGA_REG_FIRMWARE_ID, &firmware_id);
+ if (ret)
+ return ret;
+
+ build = (firmware_id >> FIRMWARE_ID_BUILD_OFFSET) & FIRMWARE_ID_MASK;
+ major = (firmware_id >> FIRMWARE_ID_MAJOR_OFFSET) & FIRMWARE_ID_MASK;
+ minor = (firmware_id >> FIRMWARE_ID_MINOR_OFFSET) & FIRMWARE_ID_MASK;
+ patch = (firmware_id >> FIRMWARE_ID_PATCH_OFFSET) & FIRMWARE_ID_MASK;
+
+ if (major != SUPPORTED_FW_MAJOR) {
+ dev_err(fpga->dev, "unsupported FPGA FW v%u.%u.%u build 0x%02x",
+ major, minor, patch, build);
+
+ return -ENODEV;
+ }
+
+ dev_info(fpga->dev, "compatible FPGA FW v%u.%u.%u build 0x%02x",
+ major, minor, patch, build);
+
+ return 0;
+}
+
+/*
+ * MFD upboard-fpga is ACPI driver and can recognize the AANT ID from different
+ * kind of upboards. We get the LED GPIO initialized information from this
+ * then add led-upboard driver.
+ */
+int upboard_led_gpio_register(struct upboard_fpga *fpga)
+{
+ struct gpio_led blue_led, yellow_led, green_led, red_led;
+ struct gpio_desc *desc;
+ static struct gpio_led upboard_gpio_leds[4];
+ int leds = 0;
+ static struct gpio_led_platform_data upboard_gpio_led_platform_data;
+ static const struct mfd_cell upboard_gpio_led_cells[] = {
+ MFD_CELL_BASIC("leds-gpio", NULL,
+ &upboard_gpio_led_platform_data,
+ sizeof(upboard_gpio_led_platform_data), 0)
+ };
+ int ret;
+
+ desc = devm_gpiod_get(fpga->dev, "blue", GPIOD_OUT_LOW);
+ if (!IS_ERR(desc)) {
+ blue_led.name = "upboard:blue:";
+ blue_led.gpio = desc_to_gpio(desc);
+ blue_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
+ upboard_gpio_leds[leds++] = blue_led;
+ devm_gpiod_put(fpga->dev, desc);
+ }
+ desc = devm_gpiod_get(fpga->dev, "yellow", GPIOD_OUT_LOW);
+ if (!IS_ERR(desc)) {
+ yellow_led.name = "upboard:yellow:";
+ yellow_led.gpio = desc_to_gpio(desc);
+ yellow_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
+ upboard_gpio_leds[leds++] = yellow_led;
+ devm_gpiod_put(fpga->dev, desc);
+ }
+ desc = devm_gpiod_get(fpga->dev, "green", GPIOD_OUT_LOW);
+ if (!IS_ERR(desc)) {
+ green_led.name = "upboard:green:";
+ green_led.gpio = desc_to_gpio(desc);
+ green_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
+ upboard_gpio_leds[leds++] = green_led;
+ devm_gpiod_put(fpga->dev, desc);
+ }
+ desc = devm_gpiod_get(fpga->dev, "red", GPIOD_OUT_LOW);
+ if (!IS_ERR(desc)) {
+ red_led.name = "upboard:red:";
+ red_led.gpio = desc_to_gpio(desc);
+ red_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
+ upboard_gpio_leds[leds++] = red_led;
+ devm_gpiod_put(fpga->dev, desc);
+ }
+
+ /* no LEDs */
+ if (leds == 0)
+ return 0;
+
+ upboard_gpio_led_platform_data.num_leds = leds;
+ upboard_gpio_led_platform_data.leds = upboard_gpio_leds;
+
+ ret = devm_mfd_add_devices(fpga->dev, PLATFORM_DEVID_AUTO,
+ upboard_gpio_led_cells,
+ ARRAY_SIZE(upboard_gpio_led_cells),
+ NULL, 0, NULL);
+ if (ret) {
+ dev_err(fpga->dev, "Failed to add GPIO LEDs,%d", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct acpi_device_id upboard_fpga_acpi_match[] = {
+ { "AANT0000", (kernel_ulong_t)&upboard_pinctrl_data },
+ { "AANT0F00", (kernel_ulong_t)&upboard_up_fpga_data },
+ { "AANT0F01", (kernel_ulong_t)&upboard_up2_fpga_data },
+ { "AANT0F02", (kernel_ulong_t)&upboard_up_fpga_data },
+ { "AANT0F03", (kernel_ulong_t)&upboard_upcore_crst02_fpga_data },
+ { "AANT0F04", (kernel_ulong_t)&upboard_up_fpga_data },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, upboard_fpga_acpi_match);
+
+static int __init upboard_fpga_probe(struct platform_device *pdev)
+{
+ struct upboard_fpga *fpga;
+ const struct acpi_device_id *id;
+ const struct upboard_fpga_data *fpga_data;
+ int ret;
+ struct device *dev = &pdev->dev;
+
+ id = acpi_match_device(upboard_fpga_acpi_match, dev);
+ if (!id)
+ return -ENODEV;
+
+ fpga_data = (const struct upboard_fpga_data *) id->driver_data;
+
+ fpga = devm_kzalloc(dev, sizeof(*fpga), GFP_KERNEL);
+ if (!fpga)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, fpga);
+ fpga->regmap = devm_regmap_init(dev, NULL, fpga, fpga_data->cpld_config);
+ fpga->cpld_config = (struct regmap_config *)fpga_data->cpld_config;
+
+ if (IS_ERR(fpga->regmap))
+ return PTR_ERR(fpga->regmap);
+
+ ret = upboard_fpga_gpio_init(fpga);
+ if (ret) {
+ /*
+ * This is for compatiable with some upboards w/o FPGA firmware,
+ * so just showing debug info and do not return directly.
+ */
+ dev_warn(dev, "Failed to initialize FPGA common GPIOs: %d", ret);
+ } else {
+ upboard_fpga_show_firmware_info(fpga);
+ }
+
+ /* register GPIO LEDs */
+ ret = upboard_led_gpio_register(fpga);
+ if (ret) {
+ /*
+ * This is for compatiable with some upboards w/o LEDs.
+ */
+ dev_warn(dev, "Failed to register LEDs: %d", ret);
+ }
+
+ return devm_mfd_add_devices(dev, PLATFORM_DEVID_AUTO,
+ fpga_data->cells,
+ fpga_data->ncells,
+ NULL, 0, NULL);
+}
+
+static struct platform_driver upboard_fpga_driver = {
+ .driver = {
+ .name = "upboard-fpga",
+ .acpi_match_table = upboard_fpga_acpi_match,
+ },
+};
+module_platform_driver_probe(upboard_fpga_driver, upboard_fpga_probe);
+
+MODULE_AUTHOR("Gary Wang <garywang@aaeon.com.tw>");
+MODULE_DESCRIPTION("UP Board CPLD/FPGA driver");
+MODULE_LICENSE("GPL v2");
new file mode 100644
@@ -0,0 +1,61 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * UP Board CPLD/FPGA driver
+ *
+ * Copyright (c) AAEON. All rights reserved.
+ *
+ * Author: Gary Wang <garywang@aaeon.com.tw>
+ *
+ */
+
+#ifndef __LINUX_MFD_UPBOARD_FPGA_H
+#define __LINUX_MFD_UPBOARD_FPGA_H
+
+#include <linux/device.h>
+#include <linux/regmap.h>
+
+/* CPLD/FPGA protocol version */
+#define UPFPGA_PROTOCOL_V1_HRV 1
+#define UPFPGA_PROTOCOL_V2_HRV 2
+
+#define UPFPGA_ADDRESS_SIZE 7
+#define UPFPGA_REGISTER_SIZE 16
+
+#define UPFPGA_READ_FLAG (1 << UPFPGA_ADDRESS_SIZE)
+
+enum upboard_fpgareg {
+ UPFPGA_REG_PLATFORM_ID = 0x10,
+ UPFPGA_REG_FIRMWARE_ID = 0x11,
+ UPFPGA_REG_FUNC_EN0 = 0x20,
+ UPFPGA_REG_FUNC_EN1 = 0x21,
+ UPFPGA_REG_GPIO_EN0 = 0x30,
+ UPFPGA_REG_GPIO_EN1 = 0x31,
+ UPFPGA_REG_GPIO_EN2 = 0x32,
+ UPFPGA_REG_GPIO_DIR0 = 0x40,
+ UPFPGA_REG_GPIO_DIR1 = 0x41,
+ UPFPGA_REG_GPIO_DIR2 = 0x42,
+ UPFPGA_REG_MAX,
+};
+
+struct upboard_fpga {
+ struct device *dev;
+ struct regmap *regmap;
+ struct regmap_config *cpld_config;
+ struct gpio_desc *enable_gpio;
+ struct gpio_desc *reset_gpio;
+ struct gpio_desc *clear_gpio;
+ struct gpio_desc *strobe_gpio;
+ struct gpio_desc *datain_gpio;
+ struct gpio_desc *dataout_gpio;
+ bool uninitialised;
+};
+
+struct upboard_led_data {
+ unsigned int bit;
+ const char *colour;
+};
+
+bool regmap_check_writeable(struct upboard_fpga *fpga, unsigned int reg);
+int upboard_led_gpio_register(struct upboard_fpga *fpga);
+
+#endif /* __LINUX_MFD_UPBOARD_FPGA_H */
The UP Squared board <http://www.upboard.com> implements certain features (pin control, onboard LEDs or CEC) through an on-board CPLD/FPGA. This mfd driver implements the line protocol to read and write registers from the FPGA through regmap. The register address map is also included. The UP Boards provide a few I/O pin headers (for both GPIO and functions), including a 40-pin Raspberry Pi compatible header. This patch implements support for the FPGA-based pin controller that manages direction and enable state for those header pins. Partial support UP boards: * UP core + CREX * UP core + CRST02 Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: larry.lai <larry.lai@yunjingtech.com> --- RFC 2023/04/25 -> PATCH V4 (1) Fixed kernel test robot compiler warning. (2) Remove mistakes with wrong Reviewed-by tags. RFC 2022/11/23 -> RFC 2023/04/25 (1) Refer 2022/12/08 Andy Shevchenko review, cleaned up coding style and addressed review comments. PATCH V3 -> RFC 2022/11/23: (1) Refer 2022/11/16 Lee Jones review, cleaned up coding style and addressed review comments. (2) Description on the UP Boards FPGA register read/write protocols PATCH V2 -> V3: (1) fixed kernel test robot compiler warning. PATCH V1 -> V2: (1) Synchronizing upboard github to rc2 (2) Refer 2022/10/31 Lee Jones review, fixed some of the issues. --- drivers/mfd/Kconfig | 12 + drivers/mfd/Makefile | 1 + drivers/mfd/upboard-fpga.c | 526 +++++++++++++++++++++++++++++++ include/linux/mfd/upboard-fpga.h | 61 ++++ 4 files changed, 600 insertions(+) create mode 100644 drivers/mfd/upboard-fpga.c create mode 100644 include/linux/mfd/upboard-fpga.h