diff mbox series

[v5,1/4] dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl

Message ID 20230209143702.44408-2-hal.feng@starfivetech.com
State New
Headers show
Series Basic pinctrl support for StarFive JH7110 RISC-V SoC | expand

Commit Message

Hal Feng Feb. 9, 2023, 2:36 p.m. UTC
From: Jianlong Huang <jianlong.huang@starfivetech.com>

Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jianlong Huang <jianlong.huang@starfivetech.com>
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
---
 .../pinctrl/starfive,jh7110-sys-pinctrl.yaml  | 142 ++++++++++++++++++
 MAINTAINERS                                   |   6 +-
 .../pinctrl/starfive,jh7110-pinctrl.h         | 115 ++++++++++++++
 3 files changed, 261 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
 create mode 100644 include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
new file mode 100644
index 000000000000..222b9e240f8a
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
@@ -0,0 +1,142 @@ 
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 SYS Pin Controller
+
+description: |
+  Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
+
+  Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63
+  can be multiplexed and have configurable bias, drive strength,
+  schmitt trigger etc.
+  Some peripherals have their I/O go through the 64 "GPIOs". This also
+  includes a number of other UARTs, I2Cs, SPIs, PWMs etc.
+  All these peripherals are connected to all 64 GPIOs such that
+  any GPIO can be set up to be controlled by any of the peripherals.
+
+maintainers:
+  - Jianlong Huang <jianlong.huang@starfivetech.com>
+
+properties:
+  compatible:
+    const: starfive,jh7110-sys-pinctrl
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 2
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+
+patternProperties:
+  '-[0-9]+$':
+    type: object
+    additionalProperties: false
+    patternProperties:
+      '-pins$':
+        type: object
+        description: |
+          A pinctrl node should contain at least one subnode representing the
+          pinctrl groups available on the machine. Each subnode will list the
+          pins it needs, and how they should be configured, with regard to
+          muxer configuration, bias, input enable/disable, input schmitt
+          trigger enable/disable, slew-rate and drive strength.
+        allOf:
+          - $ref: /schemas/pinctrl/pincfg-node.yaml
+          - $ref: /schemas/pinctrl/pinmux-node.yaml
+        additionalProperties: false
+
+        properties:
+          pinmux:
+            description: |
+              The list of GPIOs and their mux settings that properties in the
+              node apply to. This should be set using the GPIOMUX or PINMUX
+              macros.
+
+          bias-disable: true
+
+          bias-pull-up:
+            type: boolean
+
+          bias-pull-down:
+            type: boolean
+
+          drive-strength:
+            enum: [ 2, 4, 8, 12 ]
+
+          input-enable: true
+
+          input-disable: true
+
+          input-schmitt-enable: true
+
+          input-schmitt-disable: true
+
+          slew-rate:
+            maximum: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+  - interrupt-controller
+  - '#interrupt-cells'
+  - gpio-controller
+  - '#gpio-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    pinctrl@13040000 {
+        compatible = "starfive,jh7110-sys-pinctrl";
+        reg = <0x13040000 0x10000>;
+        clocks = <&syscrg 112>;
+        resets = <&syscrg 2>;
+        interrupts = <86>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        gpio-controller;
+        #gpio-cells = <2>;
+
+        uart0-0 {
+            tx-pins {
+                pinmux = <0xff140005>;
+                bias-disable;
+                drive-strength = <12>;
+                input-disable;
+                input-schmitt-disable;
+                slew-rate = <0>;
+            };
+
+            rx-pins {
+                pinmux = <0x0E000406>;
+                bias-pull-up;
+                drive-strength = <2>;
+                input-enable;
+                input-schmitt-enable;
+                slew-rate = <0>;
+            };
+        };
+    };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index f61eb221415b..babd133cdc4b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19890,13 +19890,15 @@  F:	Documentation/devicetree/bindings/clock/starfive,jh7100-*.yaml
 F:	drivers/clk/starfive/clk-starfive-jh7100*
 F:	include/dt-bindings/clock/starfive-jh7100*.h
 
-STARFIVE JH7100 PINCTRL DRIVER
+STARFIVE JH71X0 PINCTRL DRIVERS
 M:	Emil Renner Berthing <kernel@esmil.dk>
+M:	Jianlong Huang <jianlong.huang@starfivetech.com>
 L:	linux-gpio@vger.kernel.org
 S:	Maintained
-F:	Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
+F:	Documentation/devicetree/bindings/pinctrl/starfive,jh71*.yaml
 F:	drivers/pinctrl/starfive/
 F:	include/dt-bindings/pinctrl/pinctrl-starfive-jh7100.h
+F:	include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
 
 STARFIVE JH7100 RESET CONTROLLER DRIVER
 M:	Emil Renner Berthing <kernel@esmil.dk>
diff --git a/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
new file mode 100644
index 000000000000..57c1659e4bbf
--- /dev/null
+++ b/include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
@@ -0,0 +1,115 @@ 
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk>
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
+ */
+
+#ifndef __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__
+#define __DT_BINDINGS_PINCTRL_STARFIVE_JH7110_H__
+
+/* sys_iomux pins */
+#define	PAD_GPIO0		0
+#define	PAD_GPIO1		1
+#define	PAD_GPIO2		2
+#define	PAD_GPIO3		3
+#define	PAD_GPIO4		4
+#define	PAD_GPIO5		5
+#define	PAD_GPIO6		6
+#define	PAD_GPIO7		7
+#define	PAD_GPIO8		8
+#define	PAD_GPIO9		9
+#define	PAD_GPIO10		10
+#define	PAD_GPIO11		11
+#define	PAD_GPIO12		12
+#define	PAD_GPIO13		13
+#define	PAD_GPIO14		14
+#define	PAD_GPIO15		15
+#define	PAD_GPIO16		16
+#define	PAD_GPIO17		17
+#define	PAD_GPIO18		18
+#define	PAD_GPIO19		19
+#define	PAD_GPIO20		20
+#define	PAD_GPIO21		21
+#define	PAD_GPIO22		22
+#define	PAD_GPIO23		23
+#define	PAD_GPIO24		24
+#define	PAD_GPIO25		25
+#define	PAD_GPIO26		26
+#define	PAD_GPIO27		27
+#define	PAD_GPIO28		28
+#define	PAD_GPIO29		29
+#define	PAD_GPIO30		30
+#define	PAD_GPIO31		31
+#define	PAD_GPIO32		32
+#define	PAD_GPIO33		33
+#define	PAD_GPIO34		34
+#define	PAD_GPIO35		35
+#define	PAD_GPIO36		36
+#define	PAD_GPIO37		37
+#define	PAD_GPIO38		38
+#define	PAD_GPIO39		39
+#define	PAD_GPIO40		40
+#define	PAD_GPIO41		41
+#define	PAD_GPIO42		42
+#define	PAD_GPIO43		43
+#define	PAD_GPIO44		44
+#define	PAD_GPIO45		45
+#define	PAD_GPIO46		46
+#define	PAD_GPIO47		47
+#define	PAD_GPIO48		48
+#define	PAD_GPIO49		49
+#define	PAD_GPIO50		50
+#define	PAD_GPIO51		51
+#define	PAD_GPIO52		52
+#define	PAD_GPIO53		53
+#define	PAD_GPIO54		54
+#define	PAD_GPIO55		55
+#define	PAD_GPIO56		56
+#define	PAD_GPIO57		57
+#define	PAD_GPIO58		58
+#define	PAD_GPIO59		59
+#define	PAD_GPIO60		60
+#define	PAD_GPIO61		61
+#define	PAD_GPIO62		62
+#define	PAD_GPIO63		63
+#define	PAD_SD0_CLK		64
+#define	PAD_SD0_CMD		65
+#define	PAD_SD0_DATA0		66
+#define	PAD_SD0_DATA1		67
+#define	PAD_SD0_DATA2		68
+#define	PAD_SD0_DATA3		69
+#define	PAD_SD0_DATA4		70
+#define	PAD_SD0_DATA5		71
+#define	PAD_SD0_DATA6		72
+#define	PAD_SD0_DATA7		73
+#define	PAD_SD0_STRB		74
+#define	PAD_GMAC1_MDC		75
+#define	PAD_GMAC1_MDIO		76
+#define	PAD_GMAC1_RXD0		77
+#define	PAD_GMAC1_RXD1		78
+#define	PAD_GMAC1_RXD2		79
+#define	PAD_GMAC1_RXD3		80
+#define	PAD_GMAC1_RXDV		81
+#define	PAD_GMAC1_RXC		82
+#define	PAD_GMAC1_TXD0		83
+#define	PAD_GMAC1_TXD1		84
+#define	PAD_GMAC1_TXD2		85
+#define	PAD_GMAC1_TXD3		86
+#define	PAD_GMAC1_TXEN		87
+#define	PAD_GMAC1_TXC		88
+#define	PAD_QSPI_SCLK		89
+#define	PAD_QSPI_CS0		90
+#define	PAD_QSPI_DATA0		91
+#define	PAD_QSPI_DATA1		92
+#define	PAD_QSPI_DATA2		93
+#define	PAD_QSPI_DATA3		94
+
+#define GPOUT_LOW		0
+#define GPOUT_HIGH		1
+
+#define GPOEN_ENABLE		0
+#define GPOEN_DISABLE		1
+
+#define GPI_NONE		255
+
+#endif