deleted file mode 100644
@@ -1,97 +0,0 @@
-Spreadtrum EIC controller bindings
-
-The EIC is the abbreviation of external interrupt controller, which can
-be used only in input mode. The Spreadtrum platform has 2 EIC controllers,
-one is in digital chip, and another one is in PMIC. The digital chip EIC
-controller contains 4 sub-modules: EIC-debounce, EIC-latch, EIC-async and
-EIC-sync. But the PMIC EIC controller contains only one EIC-debounce sub-
-module.
-
-The EIC-debounce sub-module provides up to 8 source input signal
-connections. A debounce mechanism is used to capture the input signals'
-stable status (millisecond resolution) and a single-trigger mechanism
-is introduced into this sub-module to enhance the input event detection
-reliability. In addition, this sub-module's clock can be shut off
-automatically to reduce power dissipation. Moreover the debounce range
-is from 1ms to 4s with a step size of 1ms. The input signal will be
-ignored if it is asserted for less than 1 ms.
-
-The EIC-latch sub-module is used to latch some special power down signals
-and generate interrupts, since the EIC-latch does not depend on the APB
-clock to capture signals.
-
-The EIC-async sub-module uses a 32kHz clock to capture the short signals
-(microsecond resolution) to generate interrupts by level or edge trigger.
-
-The EIC-sync is similar with GPIO's input function, which is a synchronized
-signal input register. It can generate interrupts by level or edge trigger
-when detecting input signals.
-
-Required properties:
-- compatible: Should be one of the following:
- "sprd,sc9860-eic-debounce",
- "sprd,sc9860-eic-latch",
- "sprd,sc9860-eic-async",
- "sprd,sc9860-eic-sync",
- "sprd,sc2731-eic".
-- reg: Define the base and range of the I/O address space containing
- the GPIO controller registers.
-- gpio-controller: Marks the device node as a GPIO controller.
-- #gpio-cells: Should be <2>. The first cell is the gpio number and
- the second cell is used to specify optional parameters.
-- interrupt-controller: Marks the device node as an interrupt controller.
-- #interrupt-cells: Should be <2>. Specifies the number of cells needed
- to encode interrupt source.
-- interrupts: Should be the port interrupt shared by all the gpios.
-
-Example:
- eic_debounce: gpio@40210000 {
- compatible = "sprd,sc9860-eic-debounce";
- reg = <0 0x40210000 0 0x80>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- eic_latch: gpio@40210080 {
- compatible = "sprd,sc9860-eic-latch";
- reg = <0 0x40210080 0 0x20>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- eic_async: gpio@402100a0 {
- compatible = "sprd,sc9860-eic-async";
- reg = <0 0x402100a0 0 0x20>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- eic_sync: gpio@402100c0 {
- compatible = "sprd,sc9860-eic-sync";
- reg = <0 0x402100c0 0 0x20>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- pmic_eic: gpio@300 {
- compatible = "sprd,sc2731-eic";
- reg = <0x300>;
- interrupt-parent = <&sc2731_pmic>;
- interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
new file mode 100644
@@ -0,0 +1,145 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright 2022 Unisoc Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/sprd,gpio-eic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Unisoc EIC controller
+
+maintainers:
+ - Orson Zhai <orsonzhai@gmail.com>
+ - Baolin Wang <baolin.wang7@gmail.com>
+ - Chunyan Zhang <zhang.lyra@gmail.com>
+
+description:
+ The EIC is the abbreviation of external interrupt controller, which can
+ be used only in input mode. The Spreadtrum platform has 2 EIC controllers,
+ one is in digital chip, and another one is in PMIC. The digital chip EIC
+ controller contains 4 sub-modules, i.e. EIC-debounce, EIC-latch, EIC-async and
+ EIC-sync. But the PMIC EIC controller contains only one EIC-debounce sub-
+ module.
+
+ The EIC-debounce sub-module provides up to 8 source input signal
+ connections. A debounce mechanism is used to capture the input signals'
+ stable status (millisecond resolution) and a single-trigger mechanism
+ is introduced into this sub-module to enhance the input event detection
+ reliability. In addition, this sub-module's clock can be shut off
+ automatically to reduce power dissipation. Moreover the debounce range
+ is from 1ms to 4s with a step size of 1ms. The input signal will be
+ ignored if it is asserted for less than 1 ms.
+
+ The EIC-latch sub-module is used to latch some special power down signals
+ and generate interrupts, since the EIC-latch does not depend on the APB
+ clock to capture signals.
+
+ The EIC-async sub-module uses a 32kHz clock to capture the short signals
+ (microsecond resolution) to generate interrupts by level or edge trigger.
+
+ The EIC-sync is similar with GPIO's input function, which is a synchronized
+ signal input register. It can generate interrupts by level or edge trigger
+ when detecting input signals.
+
+properties:
+ compatible:
+ enum:
+ - sprd,sc9860-eic-debounce
+ - sprd,sc9860-eic-latch
+ - sprd,sc9860-eic-async
+ - sprd,sc9860-eic-sync
+ - sprd,sc2731-eic
+
+ reg:
+ minItems: 1
+ maxItems: 4
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 2
+
+ interrupts:
+ maxItems: 1
+ description: The interrupt shared by all GPIO lines for this controller.
+
+required:
+ - compatible
+ - reg
+ - gpio-controller
+ - "#gpio-cells"
+ - interrupt-controller
+ - "#interrupt-cells"
+ - interrupts
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ eic_debounce: gpio@40210000 {
+ compatible = "sprd,sc9860-eic-debounce";
+ reg = <0 0x40210000 0 0x80>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ eic_latch: gpio@40210080 {
+ compatible = "sprd,sc9860-eic-latch";
+ reg = <0 0x40210080 0 0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ eic_async: gpio@402100a0 {
+ compatible = "sprd,sc9860-eic-async";
+ reg = <0 0x402100a0 0 0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ eic_sync: gpio@402100c0 {
+ compatible = "sprd,sc9860-eic-sync";
+ reg = <0 0x402100c0 0 0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ sc2730_pmic {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic_eic: gpio@300 {
+ compatible = "sprd,sc2731-eic";
+ reg = <0x300>;
+ interrupt-parent = <&sc2731_pmic>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+...