diff mbox series

[6/8] arm64: dts: qcom: pmm8155au_1: Add base dts file

Message ID 20210607113840.15435-7-bhupesh.sharma@linaro.org
State Superseded
Headers show
Series arm64: dts: qcom: Add SA8155p-adp board DTS | expand

Commit Message

Bhupesh Sharma June 7, 2021, 11:38 a.m. UTC 
Add base DTS file for pmm8155au_1 along with GPIOs, power-on, rtc and vadc
nodes.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: bhupesh.linux@gmail.com
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>

---
 arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi | 134 ++++++++++++++++++++++
 1 file changed, 134 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi

-- 
2.31.1

Comments

Bjorn Andersson June 11, 2021, 3:12 a.m. UTC | #1 
On Mon 07 Jun 06:38 CDT 2021, Bhupesh Sharma wrote:

> Add base DTS file for pmm8155au_1 along with GPIOs, power-on, rtc and vadc

> nodes.

> 

> Cc: Linus Walleij <linus.walleij@linaro.org>

> Cc: Liam Girdwood <lgirdwood@gmail.com>

> Cc: Mark Brown <broonie@kernel.org>

> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>

> Cc: Vinod Koul <vkoul@kernel.org>

> Cc: Rob Herring <robh+dt@kernel.org>

> Cc: Andy Gross <agross@kernel.org>

> Cc: devicetree@vger.kernel.org

> Cc: linux-kernel@vger.kernel.org

> Cc: linux-gpio@vger.kernel.org

> Cc: bhupesh.linux@gmail.com

> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>

> ---

>  arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi | 134 ++++++++++++++++++++++

>  1 file changed, 134 insertions(+)

>  create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi

> 

> diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi


As we describe our PMICs by including their definition to the top level
of the .dts I don't see any alternative to duplicating this as _1 and
_2. So let's go with this structure.

[..]
> +

> +&spmi_bus {

> +	pmm8155au_1_0: pmic@0 {


I don't think you need to give this a label.

> +		compatible = "qcom,pmm8155au-1", "qcom,spmi-pmic";


This is a "qcom,pmm8155au", "qcom,spmi-pmic", the labels are used to
differentiate the two instances.

> +		reg = <0x0 SPMI_USID>;

> +		#address-cells = <1>;

> +		#size-cells = <0>;

> +

[..]
> +

> +		pmm8155au_1_gpios: gpio@c000 {

> +			compatible = "qcom,pmm8155au-1-gpio";


"qcom,pmm8155au-gpio"

> +			reg = <0xc000>;

> +			gpio-controller;

> +			#gpio-cells = <2>;

> +			interrupt-controller;

> +			#interrupt-cells = <2>;

> +		};

> +	};

> +

> +	pmic@1 {

> +		compatible = "qcom,pmm8155au-1", "qcom,spmi-pmic";


"qcom,pmm8155au"

Thanks,
Bjorn

> +		reg = <0x1 SPMI_USID>;

> +		#address-cells = <1>;

> +		#size-cells = <0>;

> +	};

> +};

> -- 

> 2.31.1

>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi
new file mode 100644
index 000000000000..2392c742021d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi
@@ -0,0 +1,134 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+/ {
+	thermal-zones {
+		pmm8155au-1-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pmm8155au_1_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmm8155au_1_0: pmic@0 {
+		compatible = "qcom,pmm8155au-1", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon: power-on@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+
+				status = "disabled";
+			};
+		};
+
+		pmm8155au_1_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pmm8155au_1_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmm8155au_1_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+		};
+
+		pmm8155au_1_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pmm8155au_1_rtc: rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+
+			status = "disabled";
+		};
+
+		pmm8155au_1_gpios: gpio@c000 {
+			compatible = "qcom,pmm8155au-1-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pmm8155au-1", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};