| Message ID | 20240417153105.1794134-2-f.suligoi@asem.it |
|---|---|
| State | New |
| Headers | show |
| Series | backlight: mp3309c: fix leds flickering in pwm mode | expand |
On Wed, Apr 17, 2024 at 05:31:05PM +0200, Flavio Suligoi wrote: > The mp3309 has two configuration registers, named according to their > address (0x00 and 0x01). > In the second register (0x01), the bit DIMS (Dimming Mode Select) must > be always 0 (zero), in both analog (via i2c commands) and pwm dimming > mode. > > In the initial driver version, the DIMS bit was set in pwm mode and > reset in analog mode. > But if the DIMS bit is set in pwm dimming mode and other devices are > connected on the same i2c bus, every i2c commands on the bus generates a > flickering on the LEDs powered by the mp3309c. > > This change concerns the chip initialization and does not impact any > existing device-tree configuration. > > Signed-off-by: Flavio Suligoi <f.suligoi@asem.it> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Daniel.
On Thu, 02 May 2024, Lee Jones wrote: > On Wed, 17 Apr 2024 17:31:05 +0200, Flavio Suligoi wrote: > > The mp3309 has two configuration registers, named according to their > > address (0x00 and 0x01). > > In the second register (0x01), the bit DIMS (Dimming Mode Select) must > > be always 0 (zero), in both analog (via i2c commands) and pwm dimming > > mode. > > > > In the initial driver version, the DIMS bit was set in pwm mode and > > reset in analog mode. > > But if the DIMS bit is set in pwm dimming mode and other devices are > > connected on the same i2c bus, every i2c commands on the bus generates a > > flickering on the LEDs powered by the mp3309c. > > > > [...] > > Applied, thanks! > > [1/1] backlight: mp3309c: fix leds flickering in pwm mode > commit: ce60cddc2abf61902dfca71d630624db95315124 Applied, but in future it's; I2C, PWM and LED, thanks.
diff --git a/drivers/video/backlight/mp3309c.c b/drivers/video/backlight/mp3309c.c index 016c1296841c..a28036c964af 100644 --- a/drivers/video/backlight/mp3309c.c +++ b/drivers/video/backlight/mp3309c.c @@ -97,15 +97,10 @@ static int mp3309c_enable_device(struct mp3309c_chip *chip) /* * I2C register #1 - Set working mode: - * - set one of the two dimming mode: - * - PWM dimming using an external PWM dimming signal - * - analog dimming using I2C commands * - enable/disable synchronous mode * - set overvoltage protection (OVP) */ reg_val = 0x00; - if (chip->pdata->dimming_mode == DIMMING_PWM) - reg_val |= REG_I2C_1_DIMS; if (chip->pdata->sync_mode) reg_val |= REG_I2C_1_SYNC; reg_val |= chip->pdata->over_voltage_protection;
The mp3309 has two configuration registers, named according to their address (0x00 and 0x01). In the second register (0x01), the bit DIMS (Dimming Mode Select) must be always 0 (zero), in both analog (via i2c commands) and pwm dimming mode. In the initial driver version, the DIMS bit was set in pwm mode and reset in analog mode. But if the DIMS bit is set in pwm dimming mode and other devices are connected on the same i2c bus, every i2c commands on the bus generates a flickering on the LEDs powered by the mp3309c. This change concerns the chip initialization and does not impact any existing device-tree configuration. Signed-off-by: Flavio Suligoi <f.suligoi@asem.it> --- drivers/video/backlight/mp3309c.c | 5 ----- 1 file changed, 5 deletions(-)