@@ -2486,17 +2486,6 @@ F: arch/arm/mach-oxnas/
F: drivers/power/reset/oxnas-restart.c
N: oxnas
-ARM/PLEB SUPPORT
-M: Peter Chubb <pleb@gelato.unsw.edu.au>
-S: Maintained
-W: http://www.disy.cse.unsw.edu.au/Hardware/PLEB
-
-ARM/PT DIGITAL BOARD PORT
-M: Stefan Eletzhofer <stefan.eletzhofer@eletztrick.de>
-L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S: Maintained
-W: http://www.armlinux.org.uk/
-
ARM/QUALCOMM SUPPORT
M: Andy Gross <agross@kernel.org>
M: Bjorn Andersson <andersson@kernel.org>
@@ -922,12 +922,6 @@ config ISA
config ISA_DMA_API
bool
-config PCI_NANOENGINE
- bool "BSE nanoEngine PCI support"
- depends on SA1100_NANOENGINE
- help
- Enable PCI on the BSE nanoEngine board.
-
config ARM_ERRATA_814220
bool "ARM errata: Cache maintenance by set/way operations can execute out of order"
depends on CPU_V7
@@ -19,10 +19,6 @@ __SA1100_start:
@ Preserve r8/r7 i.e. kernel entry values
#ifdef CONFIG_SA1100_COLLIE
mov r7, #MACH_TYPE_COLLIE
-#endif
-#ifdef CONFIG_SA1100_SIMPAD
- @ UNTIL we've something like an open bootldr
- mov r7, #MACH_TYPE_SIMPAD @should be 87
#endif
mrc p15, 0, r0, c1, c0, 0 @ read control reg
ands r0, r0, #0x0d
deleted file mode 100644
@@ -1,105 +0,0 @@
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_EXPERT=y
-CONFIG_ARCH_MULTI_V4=y
-# CONFIG_ARCH_MULTI_V7 is not set
-CONFIG_ARCH_SA1100=y
-CONFIG_SA1100_BADGE4=y
-CONFIG_UNUSED_BOARD_FILES=y
-CONFIG_CMDLINE="init=/linuxrc root=/dev/mtdblock3"
-CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
-CONFIG_FPE_NWFPE=y
-CONFIG_MODULES=y
-CONFIG_MODVERSIONS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_BINFMT_MISC=m
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_IPV6 is not set
-CONFIG_BT=m
-CONFIG_BT_HCIUART=m
-CONFIG_BT_HCIVHCI=m
-# CONFIG_FW_LOADER is not set
-CONFIG_MTD=y
-CONFIG_MTD_DEBUG=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_GEOMETRY=y
-# CONFIG_MTD_CFI_I2 is not set
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_RAM=y
-CONFIG_MTD_SA1100=y
-CONFIG_PARPORT=m
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_NBD=m
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_CHR_DEV_ST=m
-CONFIG_BLK_DEV_SR=m
-CONFIG_CHR_DEV_SG=y
-CONFIG_NETDEVICES=y
-CONFIG_USB_CATC=m
-CONFIG_USB_KAWETH=m
-CONFIG_USB_PEGASUS=m
-CONFIG_USB_USBNET=m
-CONFIG_USB_ALI_M5632=y
-CONFIG_USB_AN2720=y
-CONFIG_USB_EPSON2888=y
-CONFIG_USB_KC2190=y
-# CONFIG_INPUT is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_SA1100=y
-CONFIG_SERIAL_SA1100_CONSOLE=y
-CONFIG_I2C=m
-CONFIG_I2C_CHARDEV=m
-CONFIG_I2C_ELEKTOR=m
-CONFIG_WATCHDOG=y
-CONFIG_SOFT_WATCHDOG=m
-CONFIG_SA1100_WATCHDOG=m
-CONFIG_SOUND=y
-CONFIG_SOUND_PRIME=y
-CONFIG_USB=y
-CONFIG_USB_MON=y
-CONFIG_USB_ACM=m
-CONFIG_USB_PRINTER=m
-CONFIG_USB_STORAGE=y
-CONFIG_USB_STORAGE_DEBUG=y
-CONFIG_USB_MDC800=m
-CONFIG_USB_MICROTEK=m
-CONFIG_USB_USS720=m
-CONFIG_USB_SERIAL=m
-CONFIG_USB_SERIAL_GENERIC=y
-CONFIG_USB_SERIAL_BELKIN=m
-CONFIG_USB_SERIAL_WHITEHEAT=m
-CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
-CONFIG_USB_SERIAL_EMPEG=m
-CONFIG_USB_SERIAL_FTDI_SIO=m
-CONFIG_USB_SERIAL_VISOR=m
-CONFIG_USB_SERIAL_IR=m
-CONFIG_USB_SERIAL_EDGEPORT=m
-CONFIG_USB_SERIAL_KEYSPAN_PDA=m
-CONFIG_USB_SERIAL_KEYSPAN=m
-CONFIG_USB_SERIAL_MCT_U232=m
-CONFIG_USB_SERIAL_PL2303=m
-CONFIG_USB_SERIAL_CYBERJACK=m
-CONFIG_USB_SERIAL_OMNINET=m
-CONFIG_EXT2_FS=m
-CONFIG_EXT3_FS=m
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=m
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_CRAMFS=m
-CONFIG_MINIX_FS=m
-CONFIG_NFS_FS=m
-CONFIG_NFS_V3=y
-CONFIG_SMB_FS=m
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
deleted file mode 100644
@@ -1,73 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_ARCH_MULTI_V4=y
-# CONFIG_ARCH_MULTI_V7 is not set
-CONFIG_ARCH_SA1100=y
-CONFIG_SA1100_CERF=y
-CONFIG_SA1100_CERF_FLASH_16MB=y
-CONFIG_UNUSED_BOARD_FILES=y
-CONFIG_CMDLINE="console=ttySA0,38400 root=/dev/mtdblock3 rootfstype=jffs2 rw mem=32M init=/linuxrc"
-CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
-CONFIG_CPU_FREQ_GOV_USERSPACE=m
-CONFIG_FPE_FASTFPE=y
-CONFIG_PM=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_IPV6 is not set
-CONFIG_PCCARD=m
-CONFIG_PCMCIA_SA1100=m
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_SA1100=y
-CONFIG_BLK_DEV_LOOP=m
-CONFIG_BLK_DEV_RAM=m
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_SA1100=y
-CONFIG_SERIAL_SA1100_CONSOLE=y
-CONFIG_WATCHDOG=y
-CONFIG_SA1100_WATCHDOG=m
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_CPU=y
-CONFIG_EXT2_FS=m
-CONFIG_EXT3_FS=m
-CONFIG_MSDOS_FS=m
-CONFIG_VFAT_FS=m
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_ROMFS_FS=y
-CONFIG_NFS_FS=m
-CONFIG_NFS_V3=y
-CONFIG_NFS_V4=y
-CONFIG_NFSD=m
-CONFIG_NFSD_V4=y
-CONFIG_SMB_FS=m
-CONFIG_NLS=y
-CONFIG_NLS_CODEPAGE_437=m
-CONFIG_NLS_ISO8859_1=m
-CONFIG_DEBUG_KERNEL=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
deleted file mode 100644
@@ -1,48 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_ARCH_MULTI_V4=y
-# CONFIG_ARCH_MULTI_V7 is not set
-CONFIG_ARCH_SA1100=y
-CONFIG_SA1100_HACKKIT=y
-CONFIG_UNUSED_BOARD_FILES=y
-CONFIG_CMDLINE="console=ttySA0,115200 root=/dev/ram0 initrd=0xc0400000,8M init=/rootshell"
-CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
-CONFIG_FPE_NWFPE=y
-CONFIG_MODULES=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_SYN_COOKIES=y
-# CONFIG_IPV6 is not set
-CONFIG_MTD=y
-CONFIG_MTD_DEBUG=y
-CONFIG_MTD_DEBUG_VERBOSE=3
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_SERIAL_SA1100=y
-CONFIG_SERIAL_SA1100_CONSOLE=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_CPU=y
-CONFIG_EXT2_FS=y
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_CRAMFS=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
-# CONFIG_CRC32 is not set
deleted file mode 100644
@@ -1,64 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_ARCH_MULTI_V4=y
-# CONFIG_ARCH_MULTI_V7 is not set
-CONFIG_ARCH_SA1100=y
-CONFIG_SA1100_LART=y
-CONFIG_UNUSED_BOARD_FILES=y
-CONFIG_CMDLINE="console=ttySA0,9600 root=/dev/ram"
-CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
-CONFIG_CPU_FREQ_GOV_USERSPACE=y
-CONFIG_FPE_NWFPE=y
-CONFIG_PM=y
-CONFIG_MODULES=y
-CONFIG_NET=y
-CONFIG_PACKET=m
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_SYN_COOKIES=y
-# CONFIG_IPV6 is not set
-CONFIG_MTD=y
-CONFIG_MTD_DEBUG=y
-CONFIG_MTD_DEBUG_VERBOSE=1
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_LART=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=m
-CONFIG_NET_ETHERNET=y
-CONFIG_PPP=m
-CONFIG_PPP_BSDCOMP=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_ASYNC=m
-CONFIG_SLIP=m
-CONFIG_SLIP_COMPRESSED=y
-CONFIG_SERIAL_SA1100=y
-CONFIG_SERIAL_SA1100_CONSOLE=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_SOUND=m
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_CPU=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=m
-CONFIG_REISERFS_FS=m
-CONFIG_ISO9660_FS=m
-CONFIG_JOLIET=y
-CONFIG_UDF_FS=m
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=m
-CONFIG_JFFS2_FS_DEBUG=1
-CONFIG_CRAMFS=m
-CONFIG_NFS_FS=m
-CONFIG_NFS_V3=y
-CONFIG_NFSD=m
-CONFIG_NLS=y
-CONFIG_NLS_CODEPAGE_437=m
-CONFIG_NLS_CODEPAGE_850=m
-CONFIG_NLS_ISO8859_1=m
-CONFIG_NLS_ISO8859_15=m
-CONFIG_NLS_UTF8=m
-CONFIG_DEBUG_USER=y
-CONFIG_CRC32=m
deleted file mode 100644
@@ -1,53 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-# CONFIG_HOTPLUG is not set
-# CONFIG_SHMEM is not set
-CONFIG_ARCH_MULTI_V4=y
-# CONFIG_ARCH_MULTI_V7 is not set
-CONFIG_ARCH_SA1100=y
-CONFIG_SA1100_PLEB=y
-CONFIG_UNUSED_BOARD_FILES=y
-CONFIG_CMDLINE="console=ttySA0,9600 mem=16M@0xc0000000 mem=16M@0xc8000000 root=/dev/ram initrd=0xc0400000,4M"
-CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
-CONFIG_CPU_FREQ_GOV_ONDEMAND=y
-CONFIG_FPE_NWFPE=y
-CONFIG_MODULES=y
-# CONFIG_SWAP is not set
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_SYN_COOKIES=y
-# CONFIG_IPV6 is not set
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_SA1100=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
-# CONFIG_INPUT is not set
-# CONFIG_SERIO is not set
-# CONFIG_VT is not set
-CONFIG_SERIAL_SA1100=y
-CONFIG_SERIAL_SA1100_CONSOLE=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_FS_XATTR is not set
-# CONFIG_DNOTIFY is not set
-CONFIG_MSDOS_FS=m
-CONFIG_VFAT_FS=m
-CONFIG_NFS_FS=m
-CONFIG_NFS_V3=y
-CONFIG_NLS=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
deleted file mode 100644
@@ -1,45 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_ARCH_MULTI_V4=y
-# CONFIG_ARCH_MULTI_V7 is not set
-CONFIG_ARCH_SA1100=y
-CONFIG_SA1100_SHANNON=y
-CONFIG_UNUSED_BOARD_FILES=y
-CONFIG_CMDLINE="console=ttySA0,9600 console=tty1 root=/dev/mtdblock2 init=/linuxrc"
-CONFIG_FPE_NWFPE=y
-CONFIG_MODULES=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-# CONFIG_IPV6 is not set
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_SA1100=y
-CONFIG_MTD=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_SA1100=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCMCIA=y
-CONFIG_PCMCIA_PCNET=y
-CONFIG_PCMCIA_SMC91C92=y
-CONFIG_SERIAL_SA1100=y
-CONFIG_SERIAL_SA1100_CONSOLE=y
-CONFIG_WATCHDOG=y
-CONFIG_SA1100_WATCHDOG=y
-CONFIG_FB=y
-CONFIG_FB_SA1100=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_SOUND=y
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_JFFS2_FS=y
-CONFIG_MINIX_FS=y
-CONFIG_NFS_FS=y
-CONFIG_DEBUG_USER=y
deleted file mode 100644
@@ -1,100 +0,0 @@
-CONFIG_LOCALVERSION="oe1"
-CONFIG_SYSVIPC=y
-CONFIG_PREEMPT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_EXPERT=y
-CONFIG_KALLSYMS_ALL=y
-CONFIG_KALLSYMS_EXTRA_PASS=y
-CONFIG_ARCH_MULTI_V4=y
-# CONFIG_ARCH_MULTI_V7 is not set
-CONFIG_ARCH_SA1100=y
-CONFIG_SA1100_SIMPAD=y
-CONFIG_UNUSED_BOARD_FILES=y
-CONFIG_CMDLINE="mtdparts=sa1100:512k(boot),1m(kernel),-(root) console=ttySA0 root=1f02 noinitrd mem=64M jffs2_orphaned_inodes=delete rootfstype=jffs2"
-CONFIG_FPE_NWFPE=y
-CONFIG_MODULES=y
-CONFIG_BINFMT_MISC=m
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_IPV6 is not set
-CONFIG_BT=m
-CONFIG_BT_RFCOMM=m
-CONFIG_BT_RFCOMM_TTY=y
-CONFIG_BT_BNEP=m
-CONFIG_BT_BNEP_MC_FILTER=y
-CONFIG_BT_BNEP_PROTO_FILTER=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_SA1100=y
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_GEOMETRY=y
-# CONFIG_MTD_CFI_I2 is not set
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_RAM=y
-CONFIG_MTD_SA1100=y
-CONFIG_BLK_DEV_LOOP=m
-CONFIG_BLK_DEV_RAM=m
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_NET_PCI=y
-CONFIG_NET_PCMCIA=y
-CONFIG_PCMCIA_3C574=m
-CONFIG_PCMCIA_3C589=m
-CONFIG_PCMCIA_PCNET=m
-CONFIG_PCMCIA_SMC91C92=m
-CONFIG_PCMCIA_XIRC2PS=m
-CONFIG_PPP=m
-CONFIG_PPP_BSDCOMP=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_MULTILINK=y
-CONFIG_PPPOE=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=800
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=600
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_EVBUG=y
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_SERIO=m
-CONFIG_SERIAL_SA1100=y
-CONFIG_SERIAL_SA1100_CONSOLE=y
-CONFIG_FB=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-CONFIG_SOUND=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_EXT2_FS=m
-CONFIG_EXT3_FS=m
-CONFIG_REISERFS_FS=m
-CONFIG_REISERFS_PROC_INFO=y
-CONFIG_MSDOS_FS=m
-CONFIG_VFAT_FS=m
-CONFIG_JFFS2_FS=y
-CONFIG_CRAMFS=m
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_SMB_FS=m
-CONFIG_NLS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_15=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
@@ -41,35 +41,6 @@ config ASSABET_NEPONSET
Microprocessor Development Board (Assabet) with the SA-1111
Development Board (Nepon).
-config SA1100_CERF
- bool "CerfBoard"
- depends on UNUSED_BOARD_FILES
- select ARM_SA1110_CPUFREQ
- select LEDS_GPIO_REGISTER
- help
- The Intrinsyc CerfBoard is based on the StrongARM 1110 (Discontinued).
- More information is available at:
- <http://www.intrinsyc.com/products/cerfboard/>.
-
- Say Y if configuring for an Intrinsyc CerfBoard.
- Say N otherwise.
-
-choice
- prompt "Cerf Flash available"
- depends on SA1100_CERF
- default SA1100_CERF_FLASH_8MB
-
-config SA1100_CERF_FLASH_8MB
- bool "8MB"
-
-config SA1100_CERF_FLASH_16MB
- bool "16MB"
-
-config SA1100_CERF_FLASH_32MB
- bool "32MB"
-
-endchoice
-
config SA1100_COLLIE
bool "Sharp Zaurus SL5500"
# FIXME: select ARM_SA11x0_CPUFREQ
@@ -79,16 +50,6 @@ config SA1100_COLLIE
help
Say Y here to support the Sharp Zaurus SL5500 PDAs.
-config SA1100_H3100
- bool "Compaq iPAQ H3100"
- depends on UNUSED_BOARD_FILES
- select ARM_SA1110_CPUFREQ
- select HTC_EGPIO
- select MFD_IPAQ_MICRO
- help
- Say Y here if you intend to run this kernel on the Compaq iPAQ
- H3100 handheld computer.
-
config SA1100_H3600
bool "Compaq iPAQ H3600/H3700"
select ARM_SA1110_CPUFREQ
@@ -98,15 +59,6 @@ config SA1100_H3600
Say Y here if you intend to run this kernel on the Compaq iPAQ
H3600 and H3700 handheld computers.
-config SA1100_BADGE4
- bool "HP Labs BadgePAD 4"
- depends on UNUSED_BOARD_FILES
- select ARM_SA1100_CPUFREQ
- select SA1111
- help
- Say Y here if you want to build a kernel for the HP Laboratories
- BadgePAD 4.
-
config SA1100_JORNADA720
bool "HP Jornada 720"
# FIXME: select ARM_SA11x0_CPUFREQ
@@ -126,71 +78,8 @@ config SA1100_JORNADA720_SSP
keyboard, touchscreen, backlight and battery. This driver also activates
the generic SSP which it extends.
-config SA1100_HACKKIT
- bool "HackKit Core CPU Board"
- depends on UNUSED_BOARD_FILES
- select ARM_SA1100_CPUFREQ
- help
- Say Y here to support the HackKit Core CPU Board
- <http://hackkit.eletztrick.de>;
-
-config SA1100_LART
- bool "LART"
- depends on UNUSED_BOARD_FILES
- select ARM_SA1100_CPUFREQ
- help
- Say Y here if you are using the Linux Advanced Radio Terminal
- (also known as the LART). See <http://www.lartmaker.nl/> for
- information on the LART.
-
-config SA1100_NANOENGINE
- bool "nanoEngine"
- depends on UNUSED_BOARD_FILES
- select ARM_SA1110_CPUFREQ
- select FORCE_PCI
- select PCI_NANOENGINE
- help
- Say Y here if you are using the Bright Star Engineering nanoEngine.
- See <http://www.brightstareng.com/arm/nanoeng.htm> for information
- on the BSE nanoEngine.
-
-config SA1100_PLEB
- bool "PLEB"
- depends on UNUSED_BOARD_FILES
- select ARM_SA1100_CPUFREQ
- help
- Say Y here if you are using version 1 of the Portable Linux
- Embedded Board (also known as PLEB).
- See <http://www.disy.cse.unsw.edu.au/Hardware/PLEB/>
- for more information.
-
-config SA1100_SHANNON
- bool "Shannon"
- depends on UNUSED_BOARD_FILES
- select ARM_SA1100_CPUFREQ
- select REGULATOR
- select REGULATOR_FIXED_VOLTAGE
- help
- The Shannon (also known as a Tuxscreen, and also as a IS2630) was a
- limited edition webphone produced by Philips. The Shannon is a SA1100
- platform with a 640x480 LCD, touchscreen, CIR keyboard, PCMCIA slots,
- and a telco interface.
-
-config SA1100_SIMPAD
- bool "Simpad"
- depends on UNUSED_BOARD_FILES
- select ARM_SA1110_CPUFREQ
- help
- The SIEMENS webpad SIMpad is based on the StrongARM 1110. There
- are two different versions CL4 and SL4. CL4 has 32MB RAM and 16MB
- FLASH. The SL4 version got 64 MB RAM and 32 MB FLASH and a
- PCMCIA-Slot. The version for the Germany Telecom (DTAG) is the same
- like CL4 in additional it has a PCMCIA-Slot. For more information
- visit <http://www.usa.siemens.com/> or <http://www.siemens.ch/>.
-
config SA1100_SSP
tristate "Generic PIO SSP"
- depends on UNUSED_BOARD_FILES
help
Say Y here to enable support for the generic PIO SSP driver.
This isn't for audio support, but for attached sensors and
@@ -9,32 +9,11 @@ obj-y := clock.o generic.o #nmi-oopser.o
# Specific board support
obj-$(CONFIG_SA1100_ASSABET) += assabet.o
obj-$(CONFIG_ASSABET_NEPONSET) += neponset.o
-
-obj-$(CONFIG_SA1100_BADGE4) += badge4.o
-
-obj-$(CONFIG_SA1100_CERF) += cerf.o
-
obj-$(CONFIG_SA1100_COLLIE) += collie.o
-
-obj-$(CONFIG_SA1100_H3100) += h3100.o h3xxx.o
obj-$(CONFIG_SA1100_H3600) += h3600.o h3xxx.o
-
-obj-$(CONFIG_SA1100_HACKKIT) += hackkit.o
-
obj-$(CONFIG_SA1100_JORNADA720) += jornada720.o
obj-$(CONFIG_SA1100_JORNADA720_SSP) += jornada720_ssp.o
-obj-$(CONFIG_SA1100_LART) += lart.o
-
-obj-$(CONFIG_SA1100_NANOENGINE) += nanoengine.o
-obj-$(CONFIG_PCI_NANOENGINE) += pci-nanoengine.o
-
-obj-$(CONFIG_SA1100_PLEB) += pleb.o
-
-obj-$(CONFIG_SA1100_SHANNON) += shannon.o
-
-obj-$(CONFIG_SA1100_SIMPAD) += simpad.o
-
# Miscellaneous functions
obj-$(CONFIG_PM) += pm.o sleep.o
obj-$(CONFIG_SA1100_SSP) += ssp.o
deleted file mode 100644
@@ -1,338 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-sa1100/badge4.c
- *
- * BadgePAD 4 specific initialization
- *
- * Tim Connors <connors@hpl.hp.com>
- * Christopher Hoover <ch@hpl.hp.com>
- *
- * Copyright (C) 2002 Hewlett-Packard Company
- */
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/platform_data/sa11x0-serial.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/tty.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/errno.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/setup.h>
-#include <mach/irqs.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/map.h>
-#include <asm/hardware/sa1111.h>
-
-#include <mach/badge4.h>
-
-#include "generic.h"
-
-static struct resource sa1111_resources[] = {
- [0] = DEFINE_RES_MEM(BADGE4_SA1111_BASE, 0x2000),
- [1] = DEFINE_RES_IRQ(BADGE4_IRQ_GPIO_SA1111),
-};
-
-static int badge4_sa1111_enable(void *data, unsigned devid)
-{
- if (devid == SA1111_DEVID_USB)
- badge4_set_5V(BADGE4_5V_USB, 1);
- return 0;
-}
-
-static void badge4_sa1111_disable(void *data, unsigned devid)
-{
- if (devid == SA1111_DEVID_USB)
- badge4_set_5V(BADGE4_5V_USB, 0);
-}
-
-static struct sa1111_platform_data sa1111_info = {
- .disable_devs = SA1111_DEVID_PS2_MSE,
- .enable = badge4_sa1111_enable,
- .disable = badge4_sa1111_disable,
-};
-
-static u64 sa1111_dmamask = 0xffffffffUL;
-
-static struct platform_device sa1111_device = {
- .name = "sa1111",
- .id = 0,
- .dev = {
- .dma_mask = &sa1111_dmamask,
- .coherent_dma_mask = 0xffffffff,
- .platform_data = &sa1111_info,
- },
- .num_resources = ARRAY_SIZE(sa1111_resources),
- .resource = sa1111_resources,
-};
-
-/* LEDs */
-struct gpio_led badge4_gpio_leds[] = {
- {
- .name = "badge4:red",
- .default_trigger = "heartbeat",
- .gpio = 7,
- },
- {
- .name = "badge4:green",
- .default_trigger = "cpu0",
- .gpio = 9,
- },
-};
-
-static struct gpio_led_platform_data badge4_gpio_led_info = {
- .leds = badge4_gpio_leds,
- .num_leds = ARRAY_SIZE(badge4_gpio_leds),
-};
-
-static struct platform_device badge4_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &badge4_gpio_led_info,
- }
-};
-
-static struct platform_device *devices[] __initdata = {
- &sa1111_device,
- &badge4_leds,
-};
-
-static int __init badge4_sa1111_init(void)
-{
- /*
- * Ensure that the memory bus request/grant signals are setup,
- * and the grant is held in its inactive state
- */
- sa1110_mb_disable();
-
- /*
- * Probe for SA1111.
- */
- return platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-
-/*
- * 1 x Intel 28F320C3 Advanced+ Boot Block Flash (32 Mi bit)
- * Eight 4 KiW Parameter Bottom Blocks (64 KiB)
- * Sixty-three 32 KiW Main Blocks (4032 Ki b)
- *
- * <or>
- *
- * 1 x Intel 28F640C3 Advanced+ Boot Block Flash (64 Mi bit)
- * Eight 4 KiW Parameter Bottom Blocks (64 KiB)
- * One-hundred-twenty-seven 32 KiW Main Blocks (8128 Ki b)
- */
-static struct mtd_partition badge4_partitions[] = {
- {
- .name = "BLOB boot loader",
- .offset = 0,
- .size = 0x0000A000
- }, {
- .name = "params",
- .offset = MTDPART_OFS_APPEND,
- .size = 0x00006000
- }, {
- .name = "root",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL
- }
-};
-
-static struct flash_platform_data badge4_flash_data = {
- .map_name = "cfi_probe",
- .parts = badge4_partitions,
- .nr_parts = ARRAY_SIZE(badge4_partitions),
-};
-
-static struct resource badge4_flash_resource =
- DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_64M);
-
-static int five_v_on __initdata = 0;
-
-static int __init five_v_on_setup(char *ignore)
-{
- five_v_on = 1;
- return 1;
-}
-__setup("five_v_on", five_v_on_setup);
-
-
-static int __init badge4_init(void)
-{
- int ret;
-
- if (!machine_is_badge4())
- return -ENODEV;
-
- /* LCD */
- GPCR = (BADGE4_GPIO_LGP2 | BADGE4_GPIO_LGP3 |
- BADGE4_GPIO_LGP4 | BADGE4_GPIO_LGP5 |
- BADGE4_GPIO_LGP6 | BADGE4_GPIO_LGP7 |
- BADGE4_GPIO_LGP8 | BADGE4_GPIO_LGP9 |
- BADGE4_GPIO_GPA_VID | BADGE4_GPIO_GPB_VID |
- BADGE4_GPIO_GPC_VID);
- GPDR &= ~BADGE4_GPIO_INT_VID;
- GPDR |= (BADGE4_GPIO_LGP2 | BADGE4_GPIO_LGP3 |
- BADGE4_GPIO_LGP4 | BADGE4_GPIO_LGP5 |
- BADGE4_GPIO_LGP6 | BADGE4_GPIO_LGP7 |
- BADGE4_GPIO_LGP8 | BADGE4_GPIO_LGP9 |
- BADGE4_GPIO_GPA_VID | BADGE4_GPIO_GPB_VID |
- BADGE4_GPIO_GPC_VID);
-
- /* SDRAM SPD i2c */
- GPCR = (BADGE4_GPIO_SDSDA | BADGE4_GPIO_SDSCL);
- GPDR |= (BADGE4_GPIO_SDSDA | BADGE4_GPIO_SDSCL);
-
- /* uart */
- GPCR = (BADGE4_GPIO_UART_HS1 | BADGE4_GPIO_UART_HS2);
- GPDR |= (BADGE4_GPIO_UART_HS1 | BADGE4_GPIO_UART_HS2);
-
- /* CPLD muxsel0 input for mux/adc chip select */
- GPCR = BADGE4_GPIO_MUXSEL0;
- GPDR |= BADGE4_GPIO_MUXSEL0;
-
- /* test points: J5, J6 as inputs, J7 outputs */
- GPDR &= ~(BADGE4_GPIO_TESTPT_J5 | BADGE4_GPIO_TESTPT_J6);
- GPCR = BADGE4_GPIO_TESTPT_J7;
- GPDR |= BADGE4_GPIO_TESTPT_J7;
-
- /* 5V supply rail. */
- GPCR = BADGE4_GPIO_PCMEN5V; /* initially off */
- GPDR |= BADGE4_GPIO_PCMEN5V;
-
- /* CPLD sdram type inputs; set up by blob */
- //GPDR |= (BADGE4_GPIO_SDTYP1 | BADGE4_GPIO_SDTYP0);
- printk(KERN_DEBUG __FILE__ ": SDRAM CPLD typ1=%d typ0=%d\n",
- !!(GPLR & BADGE4_GPIO_SDTYP1),
- !!(GPLR & BADGE4_GPIO_SDTYP0));
-
- /* SA1111 reset pin; set up by blob */
- //GPSR = BADGE4_GPIO_SA1111_NRST;
- //GPDR |= BADGE4_GPIO_SA1111_NRST;
-
-
- /* power management cruft */
- PGSR = 0;
- PWER = 0;
- PCFR = 0;
- PSDR = 0;
-
- PWER |= PWER_GPIO26; /* wake up on an edge from TESTPT_J5 */
- PWER |= PWER_RTC; /* wake up if rtc fires */
-
- /* drive sa1111_nrst during sleep */
- PGSR |= BADGE4_GPIO_SA1111_NRST;
- /* drive CPLD as is during sleep */
- PGSR |= (GPLR & (BADGE4_GPIO_SDTYP0|BADGE4_GPIO_SDTYP1));
-
-
- /* Now bring up the SA-1111. */
- ret = badge4_sa1111_init();
- if (ret < 0)
- printk(KERN_ERR
- "%s: SA-1111 initialization failed (%d)\n",
- __func__, ret);
-
-
- /* maybe turn on 5v0 from the start */
- badge4_set_5V(BADGE4_5V_INITIALLY, five_v_on);
-
- sa11x0_register_mtd(&badge4_flash_data, &badge4_flash_resource, 1);
-
- return 0;
-}
-
-arch_initcall(badge4_init);
-
-
-static unsigned badge4_5V_bitmap = 0;
-
-void badge4_set_5V(unsigned subsystem, int on)
-{
- unsigned long flags;
- unsigned old_5V_bitmap;
-
- local_irq_save(flags);
-
- old_5V_bitmap = badge4_5V_bitmap;
-
- if (on) {
- badge4_5V_bitmap |= subsystem;
- } else {
- badge4_5V_bitmap &= ~subsystem;
- }
-
- /* detect on->off and off->on transitions */
- if ((!old_5V_bitmap) && (badge4_5V_bitmap)) {
- /* was off, now on */
- printk(KERN_INFO "%s: enabling 5V supply rail\n", __func__);
- GPSR = BADGE4_GPIO_PCMEN5V;
- } else if ((old_5V_bitmap) && (!badge4_5V_bitmap)) {
- /* was on, now off */
- printk(KERN_INFO "%s: disabling 5V supply rail\n", __func__);
- GPCR = BADGE4_GPIO_PCMEN5V;
- }
-
- local_irq_restore(flags);
-}
-EXPORT_SYMBOL(badge4_set_5V);
-
-
-static struct map_desc badge4_io_desc[] __initdata = {
- { /* SRAM bank 1 */
- .virtual = 0xf1000000,
- .pfn = __phys_to_pfn(0x08000000),
- .length = 0x00100000,
- .type = MT_DEVICE
- }, { /* SRAM bank 2 */
- .virtual = 0xf2000000,
- .pfn = __phys_to_pfn(0x10000000),
- .length = 0x00100000,
- .type = MT_DEVICE
- }
-};
-
-static void
-badge4_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
-{
- if (!state) {
- Ser1SDCR0 |= SDCR0_UART;
- }
-}
-
-static struct sa1100_port_fns badge4_port_fns __initdata = {
- .pm = badge4_uart_pm,
-};
-
-static void __init badge4_map_io(void)
-{
- sa1100_map_io();
- iotable_init(badge4_io_desc, ARRAY_SIZE(badge4_io_desc));
-
- sa1100_register_uart_fns(&badge4_port_fns);
- sa1100_register_uart(0, 3);
- sa1100_register_uart(1, 1);
-}
-
-MACHINE_START(BADGE4, "Hewlett-Packard Laboratories BadgePAD 4")
- .atag_offset = 0x100,
- .map_io = badge4_map_io,
- .nr_irqs = SA1100_NR_IRQS,
- .init_irq = sa1100_init_irq,
- .init_late = sa11x0_init_late,
- .init_time = sa1100_timer_init,
-#ifdef CONFIG_SA1111
- .dma_zone_size = SZ_1M,
-#endif
- .restart = sa11x0_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,181 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-sa1100/cerf.c
- *
- * Apr-2003 : Removed some old PDA crud [FB]
- * Oct-2003 : Added uart2 resource [FB]
- * Jan-2004 : Removed io map for flash [FB]
- */
-
-#include <linux/init.h>
-#include <linux/gpio/machine.h>
-#include <linux/kernel.h>
-#include <linux/tty.h>
-#include <linux/platform_data/sa11x0-serial.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/map.h>
-
-#include <mach/cerf.h>
-#include <linux/platform_data/mfd-mcp-sa11x0.h>
-#include <mach/irqs.h>
-#include "generic.h"
-
-static struct resource cerfuart2_resources[] = {
- [0] = DEFINE_RES_MEM(0x80030000, SZ_64K),
-};
-
-static struct platform_device cerfuart2_device = {
- .name = "sa11x0-uart",
- .id = 2,
- .num_resources = ARRAY_SIZE(cerfuart2_resources),
- .resource = cerfuart2_resources,
-};
-
-/* Compact Flash */
-static struct gpiod_lookup_table cerf_cf_gpio_table = {
- .dev_id = "sa11x0-pcmcia.1",
- .table = {
- GPIO_LOOKUP("gpio", 19, "bvd2", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("gpio", 20, "bvd1", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("gpio", 21, "reset", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("gpio", 22, "ready", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("gpio", 23, "detect", GPIO_ACTIVE_LOW),
- { },
- },
-};
-
-/* LEDs */
-struct gpio_led cerf_gpio_leds[] = {
- {
- .name = "cerf:d0",
- .default_trigger = "heartbeat",
- .gpio = 0,
- },
- {
- .name = "cerf:d1",
- .default_trigger = "cpu0",
- .gpio = 1,
- },
- {
- .name = "cerf:d2",
- .default_trigger = "default-on",
- .gpio = 2,
- },
- {
- .name = "cerf:d3",
- .default_trigger = "default-on",
- .gpio = 3,
- },
-
-};
-
-static struct gpio_led_platform_data cerf_gpio_led_info = {
- .leds = cerf_gpio_leds,
- .num_leds = ARRAY_SIZE(cerf_gpio_leds),
-};
-
-static struct platform_device *cerf_devices[] __initdata = {
- &cerfuart2_device,
-};
-
-#ifdef CONFIG_SA1100_CERF_FLASH_32MB
-# define CERF_FLASH_SIZE 0x02000000
-#elif defined CONFIG_SA1100_CERF_FLASH_16MB
-# define CERF_FLASH_SIZE 0x01000000
-#elif defined CONFIG_SA1100_CERF_FLASH_8MB
-# define CERF_FLASH_SIZE 0x00800000
-#else
-# error "Undefined flash size for CERF"
-#endif
-
-static struct mtd_partition cerf_partitions[] = {
- {
- .name = "Bootloader",
- .size = 0x00020000,
- .offset = 0x00000000,
- }, {
- .name = "Params",
- .size = 0x00040000,
- .offset = 0x00020000,
- }, {
- .name = "Kernel",
- .size = 0x00100000,
- .offset = 0x00060000,
- }, {
- .name = "Filesystem",
- .size = CERF_FLASH_SIZE-0x00160000,
- .offset = 0x00160000,
- }
-};
-
-static struct flash_platform_data cerf_flash_data = {
- .map_name = "cfi_probe",
- .parts = cerf_partitions,
- .nr_parts = ARRAY_SIZE(cerf_partitions),
-};
-
-static struct resource cerf_flash_resource =
- DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M);
-
-static void __init cerf_init_irq(void)
-{
- sa1100_init_irq();
- irq_set_irq_type(CERF_ETH_IRQ, IRQ_TYPE_EDGE_RISING);
-}
-
-static struct map_desc cerf_io_desc[] __initdata = {
- { /* Crystal Ethernet Chip */
- .virtual = 0xf0000000,
- .pfn = __phys_to_pfn(0x08000000),
- .length = 0x00100000,
- .type = MT_DEVICE
- }
-};
-
-static void __init cerf_map_io(void)
-{
- sa1100_map_io();
- iotable_init(cerf_io_desc, ARRAY_SIZE(cerf_io_desc));
-
- sa1100_register_uart(0, 3);
- sa1100_register_uart(1, 2); /* disable this and the uart2 device for sa1100_fir */
- sa1100_register_uart(2, 1);
-}
-
-static struct mcp_plat_data cerf_mcp_data = {
- .mccr0 = MCCR0_ADM,
- .sclk_rate = 11981000,
-};
-
-static void __init cerf_init(void)
-{
- sa11x0_ppc_configure_mcp();
- platform_add_devices(cerf_devices, ARRAY_SIZE(cerf_devices));
- gpio_led_register_device(-1, &cerf_gpio_led_info);
- sa11x0_register_mtd(&cerf_flash_data, &cerf_flash_resource, 1);
- sa11x0_register_mcp(&cerf_mcp_data);
- sa11x0_register_pcmcia(1, &cerf_cf_gpio_table);
-}
-
-MACHINE_START(CERF, "Intrinsyc CerfBoard/CerfCube")
- /* Maintainer: support@intrinsyc.com */
- .map_io = cerf_map_io,
- .nr_irqs = SA1100_NR_IRQS,
- .init_irq = cerf_init_irq,
- .init_time = sa1100_timer_init,
- .init_machine = cerf_init,
- .init_late = sa11x0_init_late,
- .restart = sa11x0_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,140 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Support for Compaq iPAQ H3100 handheld computer
- *
- * Copyright (c) 2000,1 Compaq Computer Corporation. (Author: Jamey Hicks)
- * Copyright (c) 2009 Dmitry Artamonow <mad_soft@inbox.ru>
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/gpio.h>
-
-#include <video/sa1100fb.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <linux/platform_data/irda-sa11x0.h>
-
-#include <mach/h3xxx.h>
-#include <mach/irqs.h>
-
-#include "generic.h"
-
-/*
- * helper for sa1100fb
- */
-static struct gpio h3100_lcd_gpio[] = {
- { H3100_GPIO_LCD_3V_ON, GPIOF_OUT_INIT_LOW, "LCD 3V" },
- { H3XXX_EGPIO_LCD_ON, GPIOF_OUT_INIT_LOW, "LCD ON" },
-};
-
-static bool h3100_lcd_request(void)
-{
- static bool h3100_lcd_ok;
- int rc;
-
- if (h3100_lcd_ok)
- return true;
-
- rc = gpio_request_array(h3100_lcd_gpio, ARRAY_SIZE(h3100_lcd_gpio));
- if (rc)
- pr_err("%s: can't request GPIOs\n", __func__);
- else
- h3100_lcd_ok = true;
-
- return h3100_lcd_ok;
-}
-
-static void h3100_lcd_power(int enable)
-{
- if (!h3100_lcd_request())
- return;
-
- gpio_set_value(H3100_GPIO_LCD_3V_ON, enable);
- gpio_set_value(H3XXX_EGPIO_LCD_ON, enable);
-}
-
-static struct sa1100fb_mach_info h3100_lcd_info = {
- .pixclock = 406977, .bpp = 4,
- .xres = 320, .yres = 240,
-
- .hsync_len = 26, .vsync_len = 41,
- .left_margin = 4, .upper_margin = 0,
- .right_margin = 4, .lower_margin = 0,
-
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
- .cmap_greyscale = 1,
- .cmap_inverse = 1,
-
- .lccr0 = LCCR0_Mono | LCCR0_4PixMono | LCCR0_Sngl | LCCR0_Pas,
- .lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
-
- .lcd_power = h3100_lcd_power,
-};
-
-static void __init h3100_map_io(void)
-{
- h3xxx_map_io();
-
- /* Older bootldrs put GPIO2-9 in alternate mode on the
- assumption that they are used for video */
- GAFR &= ~0x000001fb;
-}
-
-/*
- * This turns the IRDA power on or off on the Compaq H3100
- */
-static struct gpio h3100_irda_gpio[] = {
- { H3100_GPIO_IR_ON, GPIOF_OUT_INIT_LOW, "IrDA power" },
- { H3100_GPIO_IR_FSEL, GPIOF_OUT_INIT_LOW, "IrDA fsel" },
-};
-
-static int h3100_irda_set_power(struct device *dev, unsigned int state)
-{
- gpio_set_value(H3100_GPIO_IR_ON, state);
- return 0;
-}
-
-static void h3100_irda_set_speed(struct device *dev, unsigned int speed)
-{
- gpio_set_value(H3100_GPIO_IR_FSEL, !(speed < 4000000));
-}
-
-static int h3100_irda_startup(struct device *dev)
-{
- return gpio_request_array(h3100_irda_gpio, sizeof(h3100_irda_gpio));
-}
-
-static void h3100_irda_shutdown(struct device *dev)
-{
- return gpio_free_array(h3100_irda_gpio, sizeof(h3100_irda_gpio));
-}
-
-static struct irda_platform_data h3100_irda_data = {
- .set_power = h3100_irda_set_power,
- .set_speed = h3100_irda_set_speed,
- .startup = h3100_irda_startup,
- .shutdown = h3100_irda_shutdown,
-};
-
-static void __init h3100_mach_init(void)
-{
- h3xxx_mach_init();
-
- sa11x0_register_pcmcia(-1, NULL);
- sa11x0_register_lcd(&h3100_lcd_info);
- sa11x0_register_irda(&h3100_irda_data);
-}
-
-MACHINE_START(H3100, "Compaq iPAQ H3100")
- .atag_offset = 0x100,
- .map_io = h3100_map_io,
- .nr_irqs = SA1100_NR_IRQS,
- .init_irq = sa1100_init_irq,
- .init_time = sa1100_timer_init,
- .init_machine = h3100_mach_init,
- .init_late = sa11x0_init_late,
- .restart = sa11x0_restart,
-MACHINE_END
-
deleted file mode 100644
@@ -1,184 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-sa1100/hackkit.c
- *
- * Copyright (C) 2002 Stefan Eletzhofer <stefan.eletzhofer@eletztrick.de>
- *
- * This file contains all HackKit tweaks. Based on original work from
- * Nicolas Pitre's assabet fixes
- */
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/tty.h>
-#include <linux/module.h>
-#include <linux/errno.h>
-#include <linux/cpufreq.h>
-#include <linux/platform_data/sa11x0-serial.h>
-#include <linux/serial_core.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/tty.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-#include <linux/pgtable.h>
-
-#include <asm/mach-types.h>
-#include <asm/setup.h>
-#include <asm/page.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/irqs.h>
-
-#include "generic.h"
-
-/**********************************************************************
- * prototypes
- */
-
-/* init funcs */
-static void __init hackkit_map_io(void);
-
-static void hackkit_uart_pm(struct uart_port *port, u_int state, u_int oldstate);
-
-/**********************************************************************
- * global data
- */
-
-/**********************************************************************
- * static data
- */
-
-static struct map_desc hackkit_io_desc[] __initdata = {
- { /* Flash bank 0 */
- .virtual = 0xe8000000,
- .pfn = __phys_to_pfn(0x00000000),
- .length = 0x01000000,
- .type = MT_DEVICE
- },
-};
-
-static struct sa1100_port_fns hackkit_port_fns __initdata = {
- .pm = hackkit_uart_pm,
-};
-
-/**********************************************************************
- * Static functions
- */
-
-static void __init hackkit_map_io(void)
-{
- sa1100_map_io();
- iotable_init(hackkit_io_desc, ARRAY_SIZE(hackkit_io_desc));
-
- sa1100_register_uart_fns(&hackkit_port_fns);
- sa1100_register_uart(0, 1); /* com port */
- sa1100_register_uart(1, 2);
- sa1100_register_uart(2, 3); /* radio module */
-
- Ser1SDCR0 |= SDCR0_SUS;
-}
-
-/**
- * hackkit_uart_pm - powermgmt callback function for system 3 UART
- * @port: uart port structure
- * @state: pm state
- * @oldstate: old pm state
- *
- */
-static void hackkit_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
-{
- /* TODO: switch on/off uart in powersave mode */
-}
-
-static struct mtd_partition hackkit_partitions[] = {
- {
- .name = "BLOB",
- .size = 0x00040000,
- .offset = 0x00000000,
- .mask_flags = MTD_WRITEABLE, /* force read-only */
- }, {
- .name = "config",
- .size = 0x00040000,
- .offset = MTDPART_OFS_APPEND,
- }, {
- .name = "kernel",
- .size = 0x00100000,
- .offset = MTDPART_OFS_APPEND,
- }, {
- .name = "initrd",
- .size = 0x00180000,
- .offset = MTDPART_OFS_APPEND,
- }, {
- .name = "rootfs",
- .size = 0x700000,
- .offset = MTDPART_OFS_APPEND,
- }, {
- .name = "data",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND,
- }
-};
-
-static struct flash_platform_data hackkit_flash_data = {
- .map_name = "cfi_probe",
- .parts = hackkit_partitions,
- .nr_parts = ARRAY_SIZE(hackkit_partitions),
-};
-
-static struct resource hackkit_flash_resource =
- DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M);
-
-/* LEDs */
-struct gpio_led hackkit_gpio_leds[] = {
- {
- .name = "hackkit:red",
- .default_trigger = "cpu0",
- .gpio = 22,
- },
- {
- .name = "hackkit:green",
- .default_trigger = "heartbeat",
- .gpio = 23,
- },
-};
-
-static struct gpio_led_platform_data hackkit_gpio_led_info = {
- .leds = hackkit_gpio_leds,
- .num_leds = ARRAY_SIZE(hackkit_gpio_leds),
-};
-
-static struct platform_device hackkit_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &hackkit_gpio_led_info,
- }
-};
-
-static void __init hackkit_init(void)
-{
- sa11x0_register_mtd(&hackkit_flash_data, &hackkit_flash_resource, 1);
- platform_device_register(&hackkit_leds);
-}
-
-/**********************************************************************
- * Exported Functions
- */
-
-MACHINE_START(HACKKIT, "HackKit Cpu Board")
- .atag_offset = 0x100,
- .map_io = hackkit_map_io,
- .nr_irqs = SA1100_NR_IRQS,
- .init_irq = sa1100_init_irq,
- .init_time = sa1100_timer_init,
- .init_machine = hackkit_init,
- .init_late = sa11x0_init_late,
- .restart = sa11x0_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,71 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-sa1100/include/mach/badge4.h
- *
- * Tim Connors <connors@hpl.hp.com>
- * Christopher Hoover <ch@hpl.hp.com>
- *
- * Copyright (C) 2002 Hewlett-Packard Company
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#error "include <mach/hardware.h> instead"
-#endif
-
-#define BADGE4_SA1111_BASE (0x48000000)
-
-/* GPIOs on the BadgePAD 4 */
-#define BADGE4_GPIO_INT_1111 GPIO_GPIO0 /* SA-1111 IRQ */
-
-#define BADGE4_GPIO_INT_VID GPIO_GPIO1 /* Video expansion */
-#define BADGE4_GPIO_LGP2 GPIO_GPIO2 /* GPIO_LDD8 */
-#define BADGE4_GPIO_LGP3 GPIO_GPIO3 /* GPIO_LDD9 */
-#define BADGE4_GPIO_LGP4 GPIO_GPIO4 /* GPIO_LDD10 */
-#define BADGE4_GPIO_LGP5 GPIO_GPIO5 /* GPIO_LDD11 */
-#define BADGE4_GPIO_LGP6 GPIO_GPIO6 /* GPIO_LDD12 */
-#define BADGE4_GPIO_LGP7 GPIO_GPIO7 /* GPIO_LDD13 */
-#define BADGE4_GPIO_LGP8 GPIO_GPIO8 /* GPIO_LDD14 */
-#define BADGE4_GPIO_LGP9 GPIO_GPIO9 /* GPIO_LDD15 */
-#define BADGE4_GPIO_GPA_VID GPIO_GPIO10 /* Video expansion */
-#define BADGE4_GPIO_GPB_VID GPIO_GPIO11 /* Video expansion */
-#define BADGE4_GPIO_GPC_VID GPIO_GPIO12 /* Video expansion */
-
-#define BADGE4_GPIO_UART_HS1 GPIO_GPIO13
-#define BADGE4_GPIO_UART_HS2 GPIO_GPIO14
-
-#define BADGE4_GPIO_MUXSEL0 GPIO_GPIO15
-#define BADGE4_GPIO_TESTPT_J7 GPIO_GPIO16
-
-#define BADGE4_GPIO_SDSDA GPIO_GPIO17 /* SDRAM SPD Data */
-#define BADGE4_GPIO_SDSCL GPIO_GPIO18 /* SDRAM SPD Clock */
-#define BADGE4_GPIO_SDTYP0 GPIO_GPIO19 /* SDRAM Type Control */
-#define BADGE4_GPIO_SDTYP1 GPIO_GPIO20 /* SDRAM Type Control */
-
-#define BADGE4_GPIO_BGNT_1111 GPIO_GPIO21 /* GPIO_MBGNT */
-#define BADGE4_GPIO_BREQ_1111 GPIO_GPIO22 /* GPIO_TREQA */
-
-#define BADGE4_GPIO_TESTPT_J6 GPIO_GPIO23
-
-#define BADGE4_GPIO_PCMEN5V GPIO_GPIO24 /* 5V power */
-
-#define BADGE4_GPIO_SA1111_NRST GPIO_GPIO25 /* SA-1111 nRESET */
-
-#define BADGE4_GPIO_TESTPT_J5 GPIO_GPIO26
-
-#define BADGE4_GPIO_CLK_1111 GPIO_GPIO27 /* GPIO_32_768kHz */
-
-/* Interrupts on the BadgePAD 4 */
-#define BADGE4_IRQ_GPIO_SA1111 IRQ_GPIO0 /* SA-1111 interrupt */
-
-
-/* PCM5ENV Usage tracking */
-
-#define BADGE4_5V_PCMCIA_SOCK0 (1<<0)
-#define BADGE4_5V_PCMCIA_SOCK1 (1<<1)
-#define BADGE4_5V_PCMCIA_SOCK(n) (1<<(n))
-#define BADGE4_5V_USB (1<<2)
-#define BADGE4_5V_INITIALLY (1<<3)
-
-#ifndef __ASSEMBLY__
-extern void badge4_set_5V(unsigned subsystem, int on);
-#endif
deleted file mode 100644
@@ -1,20 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-sa1100/include/mach/cerf.h
- *
- * Apr-2003 : Removed some old PDA crud [FB]
- */
-#ifndef _INCLUDE_CERF_H_
-#define _INCLUDE_CERF_H_
-
-
-#define CERF_ETH_IO 0xf0000000
-#define CERF_ETH_IRQ IRQ_GPIO26
-
-#define CERF_GPIO_CF_BVD2 19
-#define CERF_GPIO_CF_BVD1 20
-#define CERF_GPIO_CF_RESET 21
-#define CERF_GPIO_CF_IRQ 22
-#define CERF_GPIO_CF_CD 23
-
-#endif // _INCLUDE_CERF_H_
deleted file mode 100644
@@ -1,48 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-sa1100/include/mach/nanoengine.h
- *
- * This file contains the hardware specific definitions for nanoEngine.
- * Only include this file from SA1100-specific files.
- *
- * Copyright (C) 2010 Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
- */
-#ifndef __ASM_ARCH_NANOENGINE_H
-#define __ASM_ARCH_NANOENGINE_H
-
-#include <mach/irqs.h>
-
-#define GPIO_PC_READY0 11 /* ready for socket 0 (active high)*/
-#define GPIO_PC_READY1 12 /* ready for socket 1 (active high) */
-#define GPIO_PC_CD0 13 /* detect for socket 0 (active low) */
-#define GPIO_PC_CD1 14 /* detect for socket 1 (active low) */
-#define GPIO_PC_RESET0 15 /* reset socket 0 */
-#define GPIO_PC_RESET1 16 /* reset socket 1 */
-
-#define NANOENGINE_IRQ_GPIO_PCI IRQ_GPIO0
-#define NANOENGINE_IRQ_GPIO_PC_READY0 IRQ_GPIO11
-#define NANOENGINE_IRQ_GPIO_PC_READY1 IRQ_GPIO12
-#define NANOENGINE_IRQ_GPIO_PC_CD0 IRQ_GPIO13
-#define NANOENGINE_IRQ_GPIO_PC_CD1 IRQ_GPIO14
-
-/*
- * nanoEngine Memory Map:
- *
- * 0000.0000 - 003F.0000 - 4 MB Flash
- * C000.0000 - C1FF.FFFF - 32 MB SDRAM
- * 1860.0000 - 186F.FFFF - 1 MB Internal PCI Memory Read/Write
- * 18A1.0000 - 18A1.FFFF - 64 KB Internal PCI Config Space
- * 4000.0000 - 47FF.FFFF - 128 MB External Bus I/O - Multiplexed Mode
- * 4800.0000 - 4FFF.FFFF - 128 MB External Bus I/O - Non-Multiplexed Mode
- *
- */
-
-#define NANO_PCI_MEM_RW_PHYS 0x18600000
-#define NANO_PCI_MEM_RW_VIRT 0xf1000000
-#define NANO_PCI_MEM_RW_SIZE SZ_1M
-#define NANO_PCI_CONFIG_SPACE_PHYS 0x18A10000
-#define NANO_PCI_CONFIG_SPACE_VIRT 0xf2000000
-#define NANO_PCI_CONFIG_SPACE_SIZE SZ_64K
-
-#endif
-
deleted file mode 100644
@@ -1,40 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef _INCLUDE_SHANNON_H
-#define _INCLUDE_SHANNON_H
-
-/* taken from comp.os.inferno Tue, 12 Sep 2000 09:21:50 GMT,
- * written by <forsyth@vitanuova.com> */
-
-#define SHANNON_GPIO_SPI_FLASH GPIO_GPIO (0) /* Output - Driven low, enables SPI to flash */
-#define SHANNON_GPIO_SPI_DSP GPIO_GPIO (1) /* Output - Driven low, enables SPI to DSP */
-/* lcd lower = GPIO 2-9 */
-#define SHANNON_GPIO_SPI_OUTPUT GPIO_GPIO (10) /* Output - SPI output to DSP */
-#define SHANNON_GPIO_SPI_INPUT GPIO_GPIO (11) /* Input - SPI input from DSP */
-#define SHANNON_GPIO_SPI_CLOCK GPIO_GPIO (12) /* Output - Clock for SPI */
-#define SHANNON_GPIO_SPI_FRAME GPIO_GPIO (13) /* Output - Frame marker - not used */
-#define SHANNON_GPIO_SPI_RTS GPIO_GPIO (14) /* Input - SPI Ready to Send */
-#define SHANNON_IRQ_GPIO_SPI_RTS IRQ_GPIO14
-#define SHANNON_GPIO_SPI_CTS GPIO_GPIO (15) /* Output - SPI Clear to Send */
-#define SHANNON_GPIO_IRQ_CODEC GPIO_GPIO (16) /* in, irq from ucb1200 */
-#define SHANNON_IRQ_GPIO_IRQ_CODEC IRQ_GPIO16
-#define SHANNON_GPIO_DSP_RESET GPIO_GPIO (17) /* Output - Drive low to reset the DSP */
-#define SHANNON_GPIO_CODEC_RESET GPIO_GPIO (18) /* Output - Drive low to reset the UCB1x00 */
-#define SHANNON_GPIO_U3_RTS GPIO_GPIO (19) /* ?? */
-#define SHANNON_GPIO_U3_CTS GPIO_GPIO (20) /* ?? */
-#define SHANNON_GPIO_SENSE_12V GPIO_GPIO (21) /* Input, 12v flash unprotect detected */
-#define SHANNON_GPIO_DISP_EN 22 /* out */
-/* XXX GPIO 23 unaccounted for */
-#define SHANNON_GPIO_EJECT_0 24 /* in */
-#define SHANNON_GPIO_EJECT_1 25 /* in */
-#define SHANNON_GPIO_RDY_0 26 /* in */
-#define SHANNON_GPIO_RDY_1 27 /* in */
-
-/* MCP UCB codec GPIO pins... */
-
-#define SHANNON_UCB_GPIO_BACKLIGHT 9
-#define SHANNON_UCB_GPIO_BRIGHT_MASK 7
-#define SHANNON_UCB_GPIO_BRIGHT 6
-#define SHANNON_UCB_GPIO_CONTRAST_MASK 0x3f
-#define SHANNON_UCB_GPIO_CONTRAST 0
-
-#endif
deleted file mode 100644
@@ -1,159 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-sa1100/include/mach/simpad.h
- *
- * based of assabet.h same as HUW_Webpanel
- *
- * This file contains the hardware specific definitions for SIMpad
- *
- * 2001/05/14 Juergen Messerer <juergen.messerer@freesurf.ch>
- */
-
-#ifndef __ASM_ARCH_SIMPAD_H
-#define __ASM_ARCH_SIMPAD_H
-
-
-#define GPIO_UART1_RTS GPIO_GPIO14
-#define GPIO_UART1_DTR GPIO_GPIO7
-#define GPIO_UART1_CTS GPIO_GPIO8
-#define GPIO_UART1_DCD GPIO_GPIO23
-#define GPIO_UART1_DSR GPIO_GPIO6
-
-#define GPIO_UART3_RTS GPIO_GPIO12
-#define GPIO_UART3_DTR GPIO_GPIO16
-#define GPIO_UART3_CTS GPIO_GPIO13
-#define GPIO_UART3_DCD GPIO_GPIO18
-#define GPIO_UART3_DSR GPIO_GPIO17
-
-#define GPIO_POWER_BUTTON GPIO_GPIO0
-#define GPIO_UCB1300_IRQ GPIO_GPIO22 /* UCB GPIO and touchscreen */
-
-#define IRQ_UART1_CTS IRQ_GPIO15
-#define IRQ_UART1_DCD GPIO_GPIO23
-#define IRQ_UART1_DSR GPIO_GPIO6
-#define IRQ_UART3_CTS GPIO_GPIO13
-#define IRQ_UART3_DCD GPIO_GPIO18
-#define IRQ_UART3_DSR GPIO_GPIO17
-
-#define IRQ_GPIO_UCB1300_IRQ IRQ_GPIO22
-#define IRQ_GPIO_POWER_BUTTON IRQ_GPIO0
-
-
-/*--- PCMCIA ---*/
-#define GPIO_CF_CD 24
-#define GPIO_CF_IRQ 1
-
-/*--- SmartCard ---*/
-#define GPIO_SMART_CARD GPIO_GPIO10
-#define IRQ_GPIO_SMARD_CARD IRQ_GPIO10
-
-/*--- ucb1x00 GPIO ---*/
-#define SIMPAD_UCB1X00_GPIO_BASE (GPIO_MAX + 1)
-#define SIMPAD_UCB1X00_GPIO_PROG1 (SIMPAD_UCB1X00_GPIO_BASE)
-#define SIMPAD_UCB1X00_GPIO_PROG2 (SIMPAD_UCB1X00_GPIO_BASE + 1)
-#define SIMPAD_UCB1X00_GPIO_UP (SIMPAD_UCB1X00_GPIO_BASE + 2)
-#define SIMPAD_UCB1X00_GPIO_DOWN (SIMPAD_UCB1X00_GPIO_BASE + 3)
-#define SIMPAD_UCB1X00_GPIO_LEFT (SIMPAD_UCB1X00_GPIO_BASE + 4)
-#define SIMPAD_UCB1X00_GPIO_RIGHT (SIMPAD_UCB1X00_GPIO_BASE + 5)
-#define SIMPAD_UCB1X00_GPIO_6 (SIMPAD_UCB1X00_GPIO_BASE + 6)
-#define SIMPAD_UCB1X00_GPIO_7 (SIMPAD_UCB1X00_GPIO_BASE + 7)
-#define SIMPAD_UCB1X00_GPIO_HEADSET (SIMPAD_UCB1X00_GPIO_BASE + 8)
-#define SIMPAD_UCB1X00_GPIO_SPEAKER (SIMPAD_UCB1X00_GPIO_BASE + 9)
-
-/*--- CS3 Latch ---*/
-#define SIMPAD_CS3_GPIO_BASE (GPIO_MAX + 11)
-#define SIMPAD_CS3_VCC_5V_EN (SIMPAD_CS3_GPIO_BASE)
-#define SIMPAD_CS3_VCC_3V_EN (SIMPAD_CS3_GPIO_BASE + 1)
-#define SIMPAD_CS3_EN1 (SIMPAD_CS3_GPIO_BASE + 2)
-#define SIMPAD_CS3_EN0 (SIMPAD_CS3_GPIO_BASE + 3)
-#define SIMPAD_CS3_DISPLAY_ON (SIMPAD_CS3_GPIO_BASE + 4)
-#define SIMPAD_CS3_PCMCIA_BUFF_DIS (SIMPAD_CS3_GPIO_BASE + 5)
-#define SIMPAD_CS3_MQ_RESET (SIMPAD_CS3_GPIO_BASE + 6)
-#define SIMPAD_CS3_PCMCIA_RESET (SIMPAD_CS3_GPIO_BASE + 7)
-#define SIMPAD_CS3_DECT_POWER_ON (SIMPAD_CS3_GPIO_BASE + 8)
-#define SIMPAD_CS3_IRDA_SD (SIMPAD_CS3_GPIO_BASE + 9)
-#define SIMPAD_CS3_RS232_ON (SIMPAD_CS3_GPIO_BASE + 10)
-#define SIMPAD_CS3_SD_MEDIAQ (SIMPAD_CS3_GPIO_BASE + 11)
-#define SIMPAD_CS3_LED2_ON (SIMPAD_CS3_GPIO_BASE + 12)
-#define SIMPAD_CS3_IRDA_MODE (SIMPAD_CS3_GPIO_BASE + 13)
-#define SIMPAD_CS3_ENABLE_5V (SIMPAD_CS3_GPIO_BASE + 14)
-#define SIMPAD_CS3_RESET_SIMCARD (SIMPAD_CS3_GPIO_BASE + 15)
-
-#define SIMPAD_CS3_PCMCIA_BVD1 (SIMPAD_CS3_GPIO_BASE + 16)
-#define SIMPAD_CS3_PCMCIA_BVD2 (SIMPAD_CS3_GPIO_BASE + 17)
-#define SIMPAD_CS3_PCMCIA_VS1 (SIMPAD_CS3_GPIO_BASE + 18)
-#define SIMPAD_CS3_PCMCIA_VS2 (SIMPAD_CS3_GPIO_BASE + 19)
-#define SIMPAD_CS3_LOCK_IND (SIMPAD_CS3_GPIO_BASE + 20)
-#define SIMPAD_CS3_CHARGING_STATE (SIMPAD_CS3_GPIO_BASE + 21)
-#define SIMPAD_CS3_PCMCIA_SHORT (SIMPAD_CS3_GPIO_BASE + 22)
-#define SIMPAD_CS3_GPIO_23 (SIMPAD_CS3_GPIO_BASE + 23)
-
-#define CS3_BASE IOMEM(0xf1000000)
-
-long simpad_get_cs3_ro(void);
-long simpad_get_cs3_shadow(void);
-void simpad_set_cs3_bit(int value);
-void simpad_clear_cs3_bit(int value);
-
-#define VCC_5V_EN 0x0001 /* For 5V PCMCIA */
-#define VCC_3V_EN 0x0002 /* FOR 3.3V PCMCIA */
-#define EN1 0x0004 /* This is only for EPROM's */
-#define EN0 0x0008 /* Both should be enable for 3.3V or 5V */
-#define DISPLAY_ON 0x0010
-#define PCMCIA_BUFF_DIS 0x0020
-#define MQ_RESET 0x0040
-#define PCMCIA_RESET 0x0080
-#define DECT_POWER_ON 0x0100
-#define IRDA_SD 0x0200 /* Shutdown for powersave */
-#define RS232_ON 0x0400
-#define SD_MEDIAQ 0x0800 /* Shutdown for powersave */
-#define LED2_ON 0x1000
-#define IRDA_MODE 0x2000 /* Fast/Slow IrDA mode */
-#define ENABLE_5V 0x4000 /* Enable 5V circuit */
-#define RESET_SIMCARD 0x8000
-
-#define PCMCIA_BVD1 0x01
-#define PCMCIA_BVD2 0x02
-#define PCMCIA_VS1 0x04
-#define PCMCIA_VS2 0x08
-#define LOCK_IND 0x10
-#define CHARGING_STATE 0x20
-#define PCMCIA_SHORT 0x40
-
-/*--- Battery ---*/
-struct simpad_battery {
- unsigned char ac_status; /* line connected yes/no */
- unsigned char status; /* battery loading yes/no */
- unsigned char percentage; /* percentage loaded */
- unsigned short life; /* life till empty */
-};
-
-/* These should match the apm_bios.h definitions */
-#define SIMPAD_AC_STATUS_AC_OFFLINE 0x00
-#define SIMPAD_AC_STATUS_AC_ONLINE 0x01
-#define SIMPAD_AC_STATUS_AC_BACKUP 0x02 /* What does this mean? */
-#define SIMPAD_AC_STATUS_AC_UNKNOWN 0xff
-
-/* These bitfields are rarely "or'd" together */
-#define SIMPAD_BATT_STATUS_HIGH 0x01
-#define SIMPAD_BATT_STATUS_LOW 0x02
-#define SIMPAD_BATT_STATUS_CRITICAL 0x04
-#define SIMPAD_BATT_STATUS_CHARGING 0x08
-#define SIMPAD_BATT_STATUS_CHARGE_MAIN 0x10
-#define SIMPAD_BATT_STATUS_DEAD 0x20 /* Battery will not charge */
-#define SIMPAD_BATT_NOT_INSTALLED 0x20 /* For expansion pack batteries */
-#define SIMPAD_BATT_STATUS_FULL 0x40 /* Battery fully charged (and connected to AC) */
-#define SIMPAD_BATT_STATUS_NOBATT 0x80
-#define SIMPAD_BATT_STATUS_UNKNOWN 0xff
-
-extern int simpad_get_battery(struct simpad_battery* );
-
-#endif // __ASM_ARCH_SIMPAD_H
-
-
-
-
-
-
-
-
deleted file mode 100644
@@ -1,177 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * linux/arch/arm/mach-sa1100/lart.c
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/platform_data/sa11x0-serial.h>
-#include <linux/tty.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-
-#include <video/sa1100fb.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/page.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <linux/platform_data/mfd-mcp-sa11x0.h>
-#include <mach/irqs.h>
-
-#include "generic.h"
-
-static struct mcp_plat_data lart_mcp_data = {
- .mccr0 = MCCR0_ADM,
- .sclk_rate = 11981000,
-};
-
-#ifdef LART_GREY_LCD
-static struct sa1100fb_mach_info lart_grey_info = {
- .pixclock = 150000, .bpp = 4,
- .xres = 320, .yres = 240,
-
- .hsync_len = 1, .vsync_len = 1,
- .left_margin = 4, .upper_margin = 0,
- .right_margin = 2, .lower_margin = 0,
-
- .cmap_greyscale = 1,
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-
- .lccr0 = LCCR0_Mono | LCCR0_Sngl | LCCR0_Pas | LCCR0_4PixMono,
- .lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
-};
-#endif
-#ifdef LART_COLOR_LCD
-static struct sa1100fb_mach_info lart_color_info = {
- .pixclock = 150000, .bpp = 16,
- .xres = 320, .yres = 240,
-
- .hsync_len = 2, .vsync_len = 3,
- .left_margin = 69, .upper_margin = 14,
- .right_margin = 8, .lower_margin = 4,
-
- .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
- .lccr3 = LCCR3_OutEnH | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
-};
-#endif
-#ifdef LART_VIDEO_OUT
-static struct sa1100fb_mach_info lart_video_info = {
- .pixclock = 39721, .bpp = 16,
- .xres = 640, .yres = 480,
-
- .hsync_len = 95, .vsync_len = 2,
- .left_margin = 40, .upper_margin = 32,
- .right_margin = 24, .lower_margin = 11,
-
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-
- .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
- .lccr3 = LCCR3_OutEnL | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
-};
-#endif
-
-#ifdef LART_KIT01_LCD
-static struct sa1100fb_mach_info lart_kit01_info = {
- .pixclock = 63291, .bpp = 16,
- .xres = 640, .yres = 480,
-
- .hsync_len = 64, .vsync_len = 3,
- .left_margin = 122, .upper_margin = 45,
- .right_margin = 10, .lower_margin = 10,
-
- .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
- .lccr3 = LCCR3_OutEnH | LCCR3_PixFlEdg
-};
-#endif
-
-static void __init lart_init(void)
-{
- struct sa1100fb_mach_info *inf = NULL;
-
-#ifdef LART_GREY_LCD
- inf = &lart_grey_info;
-#endif
-#ifdef LART_COLOR_LCD
- inf = &lart_color_info;
-#endif
-#ifdef LART_VIDEO_OUT
- inf = &lart_video_info;
-#endif
-#ifdef LART_KIT01_LCD
- inf = &lart_kit01_info;
-#endif
-
- if (inf)
- sa11x0_register_lcd(inf);
-
- sa11x0_ppc_configure_mcp();
- sa11x0_register_mcp(&lart_mcp_data);
-}
-
-static struct map_desc lart_io_desc[] __initdata = {
- { /* main flash memory */
- .virtual = 0xe8000000,
- .pfn = __phys_to_pfn(0x00000000),
- .length = 0x00400000,
- .type = MT_DEVICE
- }, { /* main flash, alternative location */
- .virtual = 0xec000000,
- .pfn = __phys_to_pfn(0x08000000),
- .length = 0x00400000,
- .type = MT_DEVICE
- }
-};
-
-/* LEDs */
-struct gpio_led lart_gpio_leds[] = {
- {
- .name = "lart:red",
- .default_trigger = "cpu0",
- .gpio = 23,
- },
-};
-
-static struct gpio_led_platform_data lart_gpio_led_info = {
- .leds = lart_gpio_leds,
- .num_leds = ARRAY_SIZE(lart_gpio_leds),
-};
-
-static struct platform_device lart_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &lart_gpio_led_info,
- }
-};
-static void __init lart_map_io(void)
-{
- sa1100_map_io();
- iotable_init(lart_io_desc, ARRAY_SIZE(lart_io_desc));
-
- sa1100_register_uart(0, 3);
- sa1100_register_uart(1, 1);
- sa1100_register_uart(2, 2);
-
- GAFR |= (GPIO_UART_TXD | GPIO_UART_RXD);
- GPDR |= GPIO_UART_TXD;
- GPDR &= ~GPIO_UART_RXD;
- PPAR |= PPAR_UPR;
-
- platform_device_register(&lart_leds);
-}
-
-MACHINE_START(LART, "LART")
- .atag_offset = 0x100,
- .map_io = lart_map_io,
- .nr_irqs = SA1100_NR_IRQS,
- .init_irq = sa1100_init_irq,
- .init_machine = lart_init,
- .init_late = sa11x0_init_late,
- .init_time = sa1100_timer_init,
- .restart = sa11x0_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,136 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/mach-sa1100/nanoengine.c
- *
- * Bright Star Engineering's nanoEngine board init code.
- *
- * Copyright (C) 2010 Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
- */
-
-#include <linux/init.h>
-#include <linux/gpio/machine.h>
-#include <linux/kernel.h>
-#include <linux/platform_data/sa11x0-serial.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/root_dev.h>
-
-#include <asm/mach-types.h>
-#include <asm/setup.h>
-#include <asm/page.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/map.h>
-
-#include <mach/hardware.h>
-#include <mach/nanoengine.h>
-#include <mach/irqs.h>
-
-#include "generic.h"
-
-/* Flash bank 0 */
-static struct mtd_partition nanoengine_partitions[] = {
- {
- .name = "nanoEngine boot firmware and parameter table",
- .size = 0x00010000, /* 32K */
- .offset = 0,
- .mask_flags = MTD_WRITEABLE,
- }, {
- .name = "kernel/initrd reserved",
- .size = 0x002f0000,
- .offset = 0x00010000,
- .mask_flags = MTD_WRITEABLE,
- }, {
- .name = "experimental filesystem allocation",
- .size = 0x00100000,
- .offset = 0x00300000,
- .mask_flags = MTD_WRITEABLE,
- }
-};
-
-static struct flash_platform_data nanoengine_flash_data = {
- .map_name = "jedec_probe",
- .parts = nanoengine_partitions,
- .nr_parts = ARRAY_SIZE(nanoengine_partitions),
-};
-
-static struct resource nanoengine_flash_resources[] = {
- DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M),
- DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_32M),
-};
-
-static struct map_desc nanoengine_io_desc[] __initdata = {
- {
- /* System Registers */
- .virtual = 0xf0000000,
- .pfn = __phys_to_pfn(0x10000000),
- .length = 0x00100000,
- .type = MT_DEVICE
- }, {
- /* Internal PCI Memory Read/Write */
- .virtual = NANO_PCI_MEM_RW_VIRT,
- .pfn = __phys_to_pfn(NANO_PCI_MEM_RW_PHYS),
- .length = NANO_PCI_MEM_RW_SIZE,
- .type = MT_DEVICE
- }, {
- /* Internal PCI Config Space */
- .virtual = NANO_PCI_CONFIG_SPACE_VIRT,
- .pfn = __phys_to_pfn(NANO_PCI_CONFIG_SPACE_PHYS),
- .length = NANO_PCI_CONFIG_SPACE_SIZE,
- .type = MT_DEVICE
- }
-};
-
-static void __init nanoengine_map_io(void)
-{
- sa1100_map_io();
- iotable_init(nanoengine_io_desc, ARRAY_SIZE(nanoengine_io_desc));
-
- sa1100_register_uart(0, 1);
- sa1100_register_uart(1, 2);
- sa1100_register_uart(2, 3);
- Ser1SDCR0 |= SDCR0_UART;
- /* disable IRDA -- UART2 is used as a normal serial port */
- Ser2UTCR4 = 0;
- Ser2HSCR0 = 0;
-}
-
-static struct gpiod_lookup_table nanoengine_pcmcia0_gpio_table = {
- .dev_id = "sa11x0-pcmcia.0",
- .table = {
- GPIO_LOOKUP("gpio", 11, "ready", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("gpio", 13, "detect", GPIO_ACTIVE_LOW),
- GPIO_LOOKUP("gpio", 15, "reset", GPIO_ACTIVE_HIGH),
- { },
- },
-};
-
-static struct gpiod_lookup_table nanoengine_pcmcia1_gpio_table = {
- .dev_id = "sa11x0-pcmcia.1",
- .table = {
- GPIO_LOOKUP("gpio", 12, "ready", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("gpio", 14, "detect", GPIO_ACTIVE_LOW),
- GPIO_LOOKUP("gpio", 16, "reset", GPIO_ACTIVE_HIGH),
- { },
- },
-};
-
-static void __init nanoengine_init(void)
-{
- sa11x0_register_pcmcia(0, &nanoengine_pcmcia0_gpio_table);
- sa11x0_register_pcmcia(1, &nanoengine_pcmcia1_gpio_table);
- sa11x0_register_mtd(&nanoengine_flash_data, nanoengine_flash_resources,
- ARRAY_SIZE(nanoengine_flash_resources));
-}
-
-MACHINE_START(NANOENGINE, "BSE nanoEngine")
- .atag_offset = 0x100,
- .map_io = nanoengine_map_io,
- .nr_irqs = SA1100_NR_IRQS,
- .init_irq = sa1100_init_irq,
- .init_time = sa1100_timer_init,
- .init_machine = nanoengine_init,
- .init_late = sa11x0_init_late,
- .restart = sa11x0_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,191 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * linux/arch/arm/mach-sa1100/pci-nanoengine.c
- *
- * PCI functions for BSE nanoEngine PCI
- *
- * Copyright (C) 2010 Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
- */
-#include <linux/kernel.h>
-#include <linux/irq.h>
-#include <linux/pci.h>
-
-#include <asm/mach/pci.h>
-#include <asm/mach-types.h>
-
-#include <mach/nanoengine.h>
-#include <mach/hardware.h>
-
-static void __iomem *nanoengine_pci_map_bus(struct pci_bus *bus,
- unsigned int devfn, int where)
-{
- if (bus->number != 0 || (devfn >> 3) != 0)
- return NULL;
-
- return (void __iomem *)NANO_PCI_CONFIG_SPACE_VIRT +
- ((bus->number << 16) | (devfn << 8) | (where & ~3));
-}
-
-static struct pci_ops pci_nano_ops = {
- .map_bus = nanoengine_pci_map_bus,
- .read = pci_generic_config_read32,
- .write = pci_generic_config_write32,
-};
-
-static int __init pci_nanoengine_map_irq(const struct pci_dev *dev, u8 slot,
- u8 pin)
-{
- return NANOENGINE_IRQ_GPIO_PCI;
-}
-
-static struct resource pci_io_ports =
- DEFINE_RES_IO_NAMED(0x400, 0x400, "PCI IO");
-
-static struct resource pci_non_prefetchable_memory = {
- .name = "PCI non-prefetchable",
- .start = NANO_PCI_MEM_RW_PHYS,
- /* nanoEngine documentation says there is a 1 Megabyte window here,
- * but PCI reports just 128 + 8 kbytes. */
- .end = NANO_PCI_MEM_RW_PHYS + NANO_PCI_MEM_RW_SIZE - 1,
-/* .end = NANO_PCI_MEM_RW_PHYS + SZ_128K + SZ_8K - 1,*/
- .flags = IORESOURCE_MEM,
-};
-
-/*
- * nanoEngine PCI reports 1 Megabyte of prefetchable memory, but it
- * overlaps with previously defined memory.
- *
- * Here is what happens:
- *
-# dmesg
-...
-pci 0000:00:00.0: [8086:1209] type 0 class 0x000200
-pci 0000:00:00.0: reg 10: [mem 0x00021000-0x00021fff]
-pci 0000:00:00.0: reg 14: [io 0x0000-0x003f]
-pci 0000:00:00.0: reg 18: [mem 0x00000000-0x0001ffff]
-pci 0000:00:00.0: reg 30: [mem 0x00000000-0x000fffff pref]
-pci 0000:00:00.0: supports D1 D2
-pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
-pci 0000:00:00.0: PME# disabled
-PCI: bus0: Fast back to back transfers enabled
-pci 0000:00:00.0: BAR 6: can't assign mem pref (size 0x100000)
-pci 0000:00:00.0: BAR 2: assigned [mem 0x18600000-0x1861ffff]
-pci 0000:00:00.0: BAR 2: set to [mem 0x18600000-0x1861ffff] (PCI address [0x0-0x1ffff])
-pci 0000:00:00.0: BAR 0: assigned [mem 0x18620000-0x18620fff]
-pci 0000:00:00.0: BAR 0: set to [mem 0x18620000-0x18620fff] (PCI address [0x20000-0x20fff])
-pci 0000:00:00.0: BAR 1: assigned [io 0x0400-0x043f]
-pci 0000:00:00.0: BAR 1: set to [io 0x0400-0x043f] (PCI address [0x0-0x3f])
- *
- * On the other hand, if we do not request the prefetchable memory resource,
- * linux will alloc it first and the two non-prefetchable memory areas that
- * are our real interest will not be mapped. So we choose to map it to an
- * unused area. It gets recognized as expansion ROM, but becomes disabled.
- *
- * Here is what happens then:
- *
-# dmesg
-...
-pci 0000:00:00.0: [8086:1209] type 0 class 0x000200
-pci 0000:00:00.0: reg 10: [mem 0x00021000-0x00021fff]
-pci 0000:00:00.0: reg 14: [io 0x0000-0x003f]
-pci 0000:00:00.0: reg 18: [mem 0x00000000-0x0001ffff]
-pci 0000:00:00.0: reg 30: [mem 0x00000000-0x000fffff pref]
-pci 0000:00:00.0: supports D1 D2
-pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
-pci 0000:00:00.0: PME# disabled
-PCI: bus0: Fast back to back transfers enabled
-pci 0000:00:00.0: BAR 6: assigned [mem 0x78000000-0x780fffff pref]
-pci 0000:00:00.0: BAR 2: assigned [mem 0x18600000-0x1861ffff]
-pci 0000:00:00.0: BAR 2: set to [mem 0x18600000-0x1861ffff] (PCI address [0x0-0x1ffff])
-pci 0000:00:00.0: BAR 0: assigned [mem 0x18620000-0x18620fff]
-pci 0000:00:00.0: BAR 0: set to [mem 0x18620000-0x18620fff] (PCI address [0x20000-0x20fff])
-pci 0000:00:00.0: BAR 1: assigned [io 0x0400-0x043f]
-pci 0000:00:00.0: BAR 1: set to [io 0x0400-0x043f] (PCI address [0x0-0x3f])
-
-# lspci -vv -s 0000:00:00.0
-00:00.0 Class 0200: Device 8086:1209 (rev 09)
- Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+ INTx-
- Latency: 0 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
- Interrupt: pin A routed to IRQ 0
- Region 0: Memory at 18620000 (32-bit, non-prefetchable) [size=4K]
- Region 1: I/O ports at 0400 [size=64]
- Region 2: [virtual] Memory at 18600000 (32-bit, non-prefetchable) [size=128K]
- [virtual] Expansion ROM at 78000000 [disabled] [size=1M]
- Capabilities: [dc] Power Management version 2
- Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
- Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
- Kernel driver in use: e100
- Kernel modules: e100
- *
- */
-static struct resource pci_prefetchable_memory = {
- .name = "PCI prefetchable",
- .start = 0x78000000,
- .end = 0x78000000 + NANO_PCI_MEM_RW_SIZE - 1,
- .flags = IORESOURCE_MEM | IORESOURCE_PREFETCH,
-};
-
-static int __init pci_nanoengine_setup_resources(struct pci_sys_data *sys)
-{
- if (request_resource(&ioport_resource, &pci_io_ports)) {
- printk(KERN_ERR "PCI: unable to allocate io port region\n");
- return -EBUSY;
- }
- if (request_resource(&iomem_resource, &pci_non_prefetchable_memory)) {
- release_resource(&pci_io_ports);
- printk(KERN_ERR "PCI: unable to allocate non prefetchable\n");
- return -EBUSY;
- }
- if (request_resource(&iomem_resource, &pci_prefetchable_memory)) {
- release_resource(&pci_io_ports);
- release_resource(&pci_non_prefetchable_memory);
- printk(KERN_ERR "PCI: unable to allocate prefetchable\n");
- return -EBUSY;
- }
- pci_add_resource_offset(&sys->resources, &pci_io_ports, sys->io_offset);
- pci_add_resource_offset(&sys->resources,
- &pci_non_prefetchable_memory, sys->mem_offset);
- pci_add_resource_offset(&sys->resources,
- &pci_prefetchable_memory, sys->mem_offset);
-
- return 1;
-}
-
-int __init pci_nanoengine_setup(int nr, struct pci_sys_data *sys)
-{
- int ret = 0;
-
- pcibios_min_io = 0;
- pcibios_min_mem = 0;
-
- if (nr == 0) {
- sys->mem_offset = NANO_PCI_MEM_RW_PHYS;
- sys->io_offset = 0x400;
- ret = pci_nanoengine_setup_resources(sys);
- /* Enable alternate memory bus master mode, see
- * "Intel StrongARM SA1110 Developer's Manual",
- * section 10.8, "Alternate Memory Bus Master Mode". */
- GPDR = (GPDR & ~GPIO_MBREQ) | GPIO_MBGNT;
- GAFR |= GPIO_MBGNT | GPIO_MBREQ;
- TUCR |= TUCR_MBGPIO;
- }
-
- return ret;
-}
-
-static struct hw_pci nanoengine_pci __initdata = {
- .map_irq = pci_nanoengine_map_irq,
- .nr_controllers = 1,
- .ops = &pci_nano_ops,
- .setup = pci_nanoengine_setup,
-};
-
-static int __init nanoengine_pci_init(void)
-{
- if (machine_is_nanoengine())
- pci_common_init(&nanoengine_pci);
- return 0;
-}
-
-subsys_initcall(nanoengine_pci_init);
deleted file mode 100644
@@ -1,148 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * linux/arch/arm/mach-sa1100/pleb.c
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/tty.h>
-#include <linux/ioport.h>
-#include <linux/platform_data/sa11x0-serial.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-#include <linux/mtd/partitions.h>
-#include <linux/smc91x.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <mach/irqs.h>
-
-#include "generic.h"
-
-
-/*
- * Ethernet IRQ mappings
- */
-
-#define PLEB_ETH0_P (0x20000300) /* Ethernet 0 in PCMCIA0 IO */
-#define PLEB_ETH0_V (0xf6000300)
-
-#define GPIO_ETH0_IRQ GPIO_GPIO(21)
-#define GPIO_ETH0_EN GPIO_GPIO(26)
-
-#define IRQ_GPIO_ETH0_IRQ IRQ_GPIO21
-
-static struct resource smc91x_resources[] = {
- [0] = DEFINE_RES_MEM(PLEB_ETH0_P, 0x04000000),
-#if 0 /* Autoprobe instead, to get rising/falling edge characteristic right */
- [1] = DEFINE_RES_IRQ(IRQ_GPIO_ETH0_IRQ),
-#endif
-};
-
-static struct smc91x_platdata smc91x_platdata = {
- .flags = SMC91X_USE_16BIT | SMC91X_USE_8BIT | SMC91X_NOWAIT,
-};
-
-static struct platform_device smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .num_resources = ARRAY_SIZE(smc91x_resources),
- .resource = smc91x_resources,
- .dev = {
- .platform_data = &smc91x_platdata,
- },
-};
-
-static struct platform_device *devices[] __initdata = {
- &smc91x_device,
-};
-
-
-/*
- * Pleb's memory map
- * has flash memory (typically 4 or 8 meg) selected by
- * the two SA1100 lowest chip select outputs.
- */
-static struct resource pleb_flash_resources[] = {
- [0] = DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_8M),
- [1] = DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_8M),
-};
-
-
-static struct mtd_partition pleb_partitions[] = {
- {
- .name = "blob",
- .offset = 0,
- .size = 0x00020000,
- }, {
- .name = "kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = 0x000e0000,
- }, {
- .name = "rootfs",
- .offset = MTDPART_OFS_APPEND,
- .size = 0x00300000,
- }
-};
-
-
-static struct flash_platform_data pleb_flash_data = {
- .map_name = "cfi_probe",
- .parts = pleb_partitions,
- .nr_parts = ARRAY_SIZE(pleb_partitions),
-};
-
-
-static void __init pleb_init(void)
-{
- sa11x0_register_mtd(&pleb_flash_data, pleb_flash_resources,
- ARRAY_SIZE(pleb_flash_resources));
-
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-
-static void __init pleb_map_io(void)
-{
- sa1100_map_io();
-
- sa1100_register_uart(0, 3);
- sa1100_register_uart(1, 1);
-
- GAFR |= (GPIO_UART_TXD | GPIO_UART_RXD);
- GPDR |= GPIO_UART_TXD;
- GPDR &= ~GPIO_UART_RXD;
- PPAR |= PPAR_UPR;
-
- /*
- * Fix expansion memory timing for network card
- */
- MECR = ((2<<10) | (2<<5) | (2<<0));
-
- /*
- * Enable the SMC ethernet controller
- */
- GPDR |= GPIO_ETH0_EN; /* set to output */
- GPCR = GPIO_ETH0_EN; /* clear MCLK (enable smc) */
-
- GPDR &= ~GPIO_ETH0_IRQ;
-
- irq_set_irq_type(GPIO_ETH0_IRQ, IRQ_TYPE_EDGE_FALLING);
-}
-
-MACHINE_START(PLEB, "PLEB")
- .map_io = pleb_map_io,
- .nr_irqs = SA1100_NR_IRQS,
- .init_irq = sa1100_init_irq,
- .init_time = sa1100_timer_init,
- .init_machine = pleb_init,
- .init_late = sa11x0_init_late,
- .restart = sa11x0_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,157 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * linux/arch/arm/mach-sa1100/shannon.c
- */
-
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/gpio/machine.h>
-#include <linux/kernel.h>
-#include <linux/platform_data/sa11x0-serial.h>
-#include <linux/tty.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-
-#include <video/sa1100fb.h>
-
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/setup.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/map.h>
-#include <linux/platform_data/mfd-mcp-sa11x0.h>
-#include <mach/shannon.h>
-#include <mach/irqs.h>
-
-#include "generic.h"
-
-static struct mtd_partition shannon_partitions[] = {
- {
- .name = "BLOB boot loader",
- .offset = 0,
- .size = 0x20000
- },
- {
- .name = "kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = 0xe0000
- },
- {
- .name = "initrd",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL
- }
-};
-
-static struct flash_platform_data shannon_flash_data = {
- .map_name = "cfi_probe",
- .parts = shannon_partitions,
- .nr_parts = ARRAY_SIZE(shannon_partitions),
-};
-
-static struct resource shannon_flash_resource =
- DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_4M);
-
-static struct mcp_plat_data shannon_mcp_data = {
- .mccr0 = MCCR0_ADM,
- .sclk_rate = 11981000,
-};
-
-static struct sa1100fb_mach_info shannon_lcd_info = {
- .pixclock = 152500, .bpp = 8,
- .xres = 640, .yres = 480,
-
- .hsync_len = 4, .vsync_len = 3,
- .left_margin = 2, .upper_margin = 0,
- .right_margin = 1, .lower_margin = 0,
-
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-
- .lccr0 = LCCR0_Color | LCCR0_Dual | LCCR0_Pas,
- .lccr3 = LCCR3_ACBsDiv(512),
-};
-
-static struct gpiod_lookup_table shannon_pcmcia0_gpio_table = {
- .dev_id = "sa11x0-pcmcia.0",
- .table = {
- GPIO_LOOKUP("gpio", 24, "detect", GPIO_ACTIVE_LOW),
- GPIO_LOOKUP("gpio", 26, "ready", GPIO_ACTIVE_HIGH),
- { },
- },
-};
-
-static struct gpiod_lookup_table shannon_pcmcia1_gpio_table = {
- .dev_id = "sa11x0-pcmcia.1",
- .table = {
- GPIO_LOOKUP("gpio", 25, "detect", GPIO_ACTIVE_LOW),
- GPIO_LOOKUP("gpio", 27, "ready", GPIO_ACTIVE_HIGH),
- { },
- },
-};
-
-static struct regulator_consumer_supply shannon_cf_vcc_consumers[] = {
- REGULATOR_SUPPLY("vcc", "sa11x0-pcmcia.0"),
- REGULATOR_SUPPLY("vcc", "sa11x0-pcmcia.1"),
-};
-
-static struct fixed_voltage_config shannon_cf_vcc_pdata __initdata = {
- .supply_name = "cf-power",
- .microvolts = 3300000,
- .enabled_at_boot = 1,
-};
-
-static struct gpiod_lookup_table shannon_display_gpio_table = {
- .dev_id = "sa11x0-fb",
- .table = {
- GPIO_LOOKUP("gpio", 22, "shannon-lcden", GPIO_ACTIVE_HIGH),
- { },
- },
-};
-
-static void __init shannon_init(void)
-{
- sa11x0_register_fixed_regulator(0, &shannon_cf_vcc_pdata,
- shannon_cf_vcc_consumers,
- ARRAY_SIZE(shannon_cf_vcc_consumers),
- false);
- sa11x0_register_pcmcia(0, &shannon_pcmcia0_gpio_table);
- sa11x0_register_pcmcia(1, &shannon_pcmcia1_gpio_table);
- sa11x0_ppc_configure_mcp();
- gpiod_add_lookup_table(&shannon_display_gpio_table);
- sa11x0_register_lcd(&shannon_lcd_info);
- sa11x0_register_mtd(&shannon_flash_data, &shannon_flash_resource, 1);
- sa11x0_register_mcp(&shannon_mcp_data);
-}
-
-static void __init shannon_map_io(void)
-{
- sa1100_map_io();
-
- sa1100_register_uart(0, 3);
- sa1100_register_uart(1, 1);
-
- Ser1SDCR0 |= SDCR0_SUS;
- GAFR |= (GPIO_UART_TXD | GPIO_UART_RXD);
- GPDR |= GPIO_UART_TXD | SHANNON_GPIO_CODEC_RESET;
- GPDR &= ~GPIO_UART_RXD;
- PPAR |= PPAR_UPR;
-
- /* reset the codec */
- GPCR = SHANNON_GPIO_CODEC_RESET;
- GPSR = SHANNON_GPIO_CODEC_RESET;
-}
-
-MACHINE_START(SHANNON, "Shannon (AKA: Tuxscreen)")
- .atag_offset = 0x100,
- .map_io = shannon_map_io,
- .nr_irqs = SA1100_NR_IRQS,
- .init_irq = sa1100_init_irq,
- .init_time = sa1100_timer_init,
- .init_machine = shannon_init,
- .init_late = sa11x0_init_late,
- .restart = sa11x0_restart,
-MACHINE_END
deleted file mode 100644
@@ -1,423 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * linux/arch/arm/mach-sa1100/simpad.c
- */
-
-#include <linux/module.h>
-#include <linux/gpio/machine.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/tty.h>
-#include <linux/proc_fs.h>
-#include <linux/string.h>
-#include <linux/pm.h>
-#include <linux/platform_data/sa11x0-serial.h>
-#include <linux/platform_device.h>
-#include <linux/mfd/ucb1x00.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/io.h>
-#include <linux/gpio/driver.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/irq.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/map.h>
-#include <linux/platform_data/mfd-mcp-sa11x0.h>
-#include <mach/simpad.h>
-#include <mach/irqs.h>
-
-#include <linux/serial_core.h>
-#include <linux/ioport.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-#include <linux/leds.h>
-#include <linux/platform_data/i2c-gpio.h>
-
-#include "generic.h"
-
-/*
- * CS3 support
- */
-
-static long cs3_shadow;
-static spinlock_t cs3_lock;
-static struct gpio_chip cs3_gpio;
-
-long simpad_get_cs3_ro(void)
-{
- return readl(CS3_BASE);
-}
-EXPORT_SYMBOL(simpad_get_cs3_ro);
-
-long simpad_get_cs3_shadow(void)
-{
- return cs3_shadow;
-}
-EXPORT_SYMBOL(simpad_get_cs3_shadow);
-
-static void __simpad_write_cs3(void)
-{
- writel(cs3_shadow, CS3_BASE);
-}
-
-void simpad_set_cs3_bit(int value)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&cs3_lock, flags);
- cs3_shadow |= value;
- __simpad_write_cs3();
- spin_unlock_irqrestore(&cs3_lock, flags);
-}
-EXPORT_SYMBOL(simpad_set_cs3_bit);
-
-void simpad_clear_cs3_bit(int value)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&cs3_lock, flags);
- cs3_shadow &= ~value;
- __simpad_write_cs3();
- spin_unlock_irqrestore(&cs3_lock, flags);
-}
-EXPORT_SYMBOL(simpad_clear_cs3_bit);
-
-static void cs3_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
-{
- if (offset > 15)
- return;
- if (value)
- simpad_set_cs3_bit(1 << offset);
- else
- simpad_clear_cs3_bit(1 << offset);
-};
-
-static int cs3_gpio_get(struct gpio_chip *chip, unsigned offset)
-{
- if (offset > 15)
- return !!(simpad_get_cs3_ro() & (1 << (offset - 16)));
- return !!(simpad_get_cs3_shadow() & (1 << offset));
-};
-
-static int cs3_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
-{
- if (offset > 15)
- return 0;
- return -EINVAL;
-};
-
-static int cs3_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
- int value)
-{
- if (offset > 15)
- return -EINVAL;
- cs3_gpio_set(chip, offset, value);
- return 0;
-};
-
-static struct map_desc simpad_io_desc[] __initdata = {
- { /* MQ200 */
- .virtual = 0xf2800000,
- .pfn = __phys_to_pfn(0x4b800000),
- .length = 0x00800000,
- .type = MT_DEVICE
- }, { /* Simpad CS3 */
- .virtual = (unsigned long)CS3_BASE,
- .pfn = __phys_to_pfn(SA1100_CS3_PHYS),
- .length = 0x00100000,
- .type = MT_DEVICE
- },
-};
-
-
-static void simpad_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
-{
- if (port->mapbase == (u_int)&Ser1UTCR0) {
- if (state)
- {
- simpad_clear_cs3_bit(RS232_ON);
- simpad_clear_cs3_bit(DECT_POWER_ON);
- }else
- {
- simpad_set_cs3_bit(RS232_ON);
- simpad_set_cs3_bit(DECT_POWER_ON);
- }
- }
-}
-
-static struct sa1100_port_fns simpad_port_fns __initdata = {
- .pm = simpad_uart_pm,
-};
-
-
-static struct mtd_partition simpad_partitions[] = {
- {
- .name = "SIMpad boot firmware",
- .size = 0x00080000,
- .offset = 0,
- .mask_flags = MTD_WRITEABLE,
- }, {
- .name = "SIMpad kernel",
- .size = 0x0010000,
- .offset = MTDPART_OFS_APPEND,
- }, {
- .name = "SIMpad root jffs2",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND,
- }
-};
-
-static struct flash_platform_data simpad_flash_data = {
- .map_name = "cfi_probe",
- .parts = simpad_partitions,
- .nr_parts = ARRAY_SIZE(simpad_partitions),
-};
-
-
-static struct resource simpad_flash_resources [] = {
- DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_16M),
- DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_16M),
-};
-
-static struct ucb1x00_plat_data simpad_ucb1x00_data = {
- .gpio_base = SIMPAD_UCB1X00_GPIO_BASE,
-};
-
-static struct mcp_plat_data simpad_mcp_data = {
- .mccr0 = MCCR0_ADM,
- .sclk_rate = 11981000,
- .codec_pdata = &simpad_ucb1x00_data,
-};
-
-
-
-static void __init simpad_map_io(void)
-{
- sa1100_map_io();
-
- iotable_init(simpad_io_desc, ARRAY_SIZE(simpad_io_desc));
-
- /* Initialize CS3 */
- cs3_shadow = (EN1 | EN0 | LED2_ON | DISPLAY_ON |
- RS232_ON | ENABLE_5V | RESET_SIMCARD | DECT_POWER_ON);
- __simpad_write_cs3(); /* Spinlocks not yet initialized */
-
- sa1100_register_uart_fns(&simpad_port_fns);
- sa1100_register_uart(0, 3); /* serial interface */
- sa1100_register_uart(1, 1); /* DECT */
-
- // Reassign UART 1 pins
- GAFR |= GPIO_UART_TXD | GPIO_UART_RXD;
- GPDR |= GPIO_UART_TXD | GPIO_LDD13 | GPIO_LDD15;
- GPDR &= ~GPIO_UART_RXD;
- PPAR |= PPAR_UPR;
-
- /*
- * Set up registers for sleep mode.
- */
-
-
- PWER = PWER_GPIO0| PWER_RTC;
- PGSR = 0x818;
- PCFR = 0;
- PSDR = 0;
-
-}
-
-static void simpad_power_off(void)
-{
- local_irq_disable();
- cs3_shadow = SD_MEDIAQ;
- __simpad_write_cs3(); /* Bypass spinlock here */
-
- /* disable internal oscillator, float CS lines */
- PCFR = (PCFR_OPDE | PCFR_FP | PCFR_FS);
- /* enable wake-up on GPIO0 */
- PWER = GFER = GRER = PWER_GPIO0;
- /*
- * set scratchpad to zero, just in case it is used as a
- * restart address by the bootloader.
- */
- PSPR = 0;
- PGSR = 0;
- /* enter sleep mode */
- PMCR = PMCR_SF;
- while(1);
-
- local_irq_enable(); /* we won't ever call it */
-
-
-}
-
-/*
- * gpio_keys
-*/
-
-static struct gpio_keys_button simpad_button_table[] = {
- { KEY_POWER, IRQ_GPIO_POWER_BUTTON, 1, "power button" },
-};
-
-static struct gpio_keys_platform_data simpad_keys_data = {
- .buttons = simpad_button_table,
- .nbuttons = ARRAY_SIZE(simpad_button_table),
-};
-
-static struct platform_device simpad_keys = {
- .name = "gpio-keys",
- .dev = {
- .platform_data = &simpad_keys_data,
- },
-};
-
-static struct gpio_keys_button simpad_polled_button_table[] = {
- { KEY_PROG1, SIMPAD_UCB1X00_GPIO_PROG1, 1, "prog1 button" },
- { KEY_PROG2, SIMPAD_UCB1X00_GPIO_PROG2, 1, "prog2 button" },
- { KEY_UP, SIMPAD_UCB1X00_GPIO_UP, 1, "up button" },
- { KEY_DOWN, SIMPAD_UCB1X00_GPIO_DOWN, 1, "down button" },
- { KEY_LEFT, SIMPAD_UCB1X00_GPIO_LEFT, 1, "left button" },
- { KEY_RIGHT, SIMPAD_UCB1X00_GPIO_RIGHT, 1, "right button" },
-};
-
-static struct gpio_keys_platform_data simpad_polled_keys_data = {
- .buttons = simpad_polled_button_table,
- .nbuttons = ARRAY_SIZE(simpad_polled_button_table),
- .poll_interval = 50,
-};
-
-static struct platform_device simpad_polled_keys = {
- .name = "gpio-keys-polled",
- .dev = {
- .platform_data = &simpad_polled_keys_data,
- },
-};
-
-/*
- * GPIO LEDs
- */
-
-static struct gpio_led simpad_leds[] = {
- {
- .name = "simpad:power",
- .gpio = SIMPAD_CS3_LED2_ON,
- .active_low = 0,
- .default_trigger = "default-on",
- },
-};
-
-static struct gpio_led_platform_data simpad_led_data = {
- .num_leds = ARRAY_SIZE(simpad_leds),
- .leds = simpad_leds,
-};
-
-static struct platform_device simpad_gpio_leds = {
- .name = "leds-gpio",
- .id = 0,
- .dev = {
- .platform_data = &simpad_led_data,
- },
-};
-
-/*
- * i2c
- */
-static struct gpiod_lookup_table simpad_i2c_gpiod_table = {
- .dev_id = "i2c-gpio.0",
- .table = {
- GPIO_LOOKUP_IDX("gpio", 21, NULL, 0,
- GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
- GPIO_LOOKUP_IDX("gpio", 25, NULL, 1,
- GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
- },
-};
-
-static struct i2c_gpio_platform_data simpad_i2c_data = {
- .udelay = 10,
- .timeout = HZ,
-};
-
-static struct platform_device simpad_i2c = {
- .name = "i2c-gpio",
- .id = 0,
- .dev = {
- .platform_data = &simpad_i2c_data,
- },
-};
-
-/*
- * MediaQ Video Device
- */
-static struct platform_device simpad_mq200fb = {
- .name = "simpad-mq200",
- .id = 0,
-};
-
-static struct platform_device *devices[] __initdata = {
- &simpad_keys,
- &simpad_polled_keys,
- &simpad_mq200fb,
- &simpad_gpio_leds,
- &simpad_i2c,
-};
-
-/* Compact Flash */
-static struct gpiod_lookup_table simpad_cf_gpio_table = {
- .dev_id = "sa11x0-pcmcia",
- .table = {
- GPIO_LOOKUP("gpio", GPIO_CF_IRQ, "cf-ready", GPIO_ACTIVE_HIGH),
- GPIO_LOOKUP("gpio", GPIO_CF_CD, "cf-detect", GPIO_ACTIVE_HIGH),
- { },
- },
-};
-
-
-static int __init simpad_init(void)
-{
- int ret;
-
- spin_lock_init(&cs3_lock);
-
- cs3_gpio.label = "simpad_cs3";
- cs3_gpio.base = SIMPAD_CS3_GPIO_BASE;
- cs3_gpio.ngpio = 24;
- cs3_gpio.set = cs3_gpio_set;
- cs3_gpio.get = cs3_gpio_get;
- cs3_gpio.direction_input = cs3_gpio_direction_input;
- cs3_gpio.direction_output = cs3_gpio_direction_output;
- ret = gpiochip_add_data(&cs3_gpio, NULL);
- if (ret)
- printk(KERN_WARNING "simpad: Unable to register cs3 GPIO device");
-
- pm_power_off = simpad_power_off;
-
- sa11x0_register_pcmcia(-1, &simpad_cf_gpio_table);
- sa11x0_ppc_configure_mcp();
- sa11x0_register_mtd(&simpad_flash_data, simpad_flash_resources,
- ARRAY_SIZE(simpad_flash_resources));
- sa11x0_register_mcp(&simpad_mcp_data);
-
- gpiod_add_lookup_table(&simpad_i2c_gpiod_table);
- ret = platform_add_devices(devices, ARRAY_SIZE(devices));
- if(ret)
- printk(KERN_WARNING "simpad: Unable to register mq200 framebuffer device");
-
- return 0;
-}
-
-arch_initcall(simpad_init);
-
-
-MACHINE_START(SIMPAD, "Simpad")
- /* Maintainer: Holger Freyther */
- .atag_offset = 0x100,
- .map_io = simpad_map_io,
- .nr_irqs = SA1100_NR_IRQS,
- .init_irq = sa1100_init_irq,
- .init_late = sa11x0_init_late,
- .init_time = sa1100_timer_init,
- .restart = sa11x0_restart,
-MACHINE_END
@@ -344,14 +344,8 @@ static int __init sa1110_clk_init(void)
if (!name[0]) {
if (machine_is_assabet())
name = "TC59SM716-CL3";
- if (machine_is_pt_system3())
- name = "K4S641632D";
- if (machine_is_h3100())
- name = "KM416S4030CT";
if (machine_is_jornada720() || machine_is_h3600())
name = "K4S281632B-1H";
- if (machine_is_nanoengine())
- name = "MT48LC8M16A2TG-75";
}
sdram = sa1110_find_sdram(name);
@@ -672,7 +672,7 @@ config MFD_INTEL_PMC_BXT
config MFD_IPAQ_MICRO
bool "Atmel Micro ASIC (iPAQ h3100/h3600/h3700) Support"
- depends on SA1100_H3100 || SA1100_H3600
+ depends on SA1100_H3600
select MFD_CORE
help
Select this to get support for the Microcontroller found in
@@ -98,12 +98,9 @@ static struct pcmcia_low_level sa11x0_cf_ops = {
int __init pcmcia_collie_init(struct device *dev);
static int (*sa11x0_pcmcia_legacy_hw_init[])(struct device *dev) = {
-#if defined(CONFIG_SA1100_H3100) || defined(CONFIG_SA1100_H3600)
+#ifdef CONFIG_SA1100_H3600
pcmcia_h3600_init,
#endif
-#ifdef CONFIG_SA1100_SIMPAD
- pcmcia_simpad_init,
-#endif
#ifdef CONFIG_SA1100_COLLIE
pcmcia_collie_init,
#endif
@@ -156,7 +156,7 @@ int pcmcia_h3600_init(struct device *dev)
{
int ret = -ENODEV;
- if (machine_is_h3600() || machine_is_h3100())
+ if (machine_is_h3600())
ret = sa11xx_drv_pcmcia_probe(dev, &h3600_pcmcia_ops, 0, 2);
return ret;
@@ -212,10 +212,6 @@ static int pcmcia_probe(struct sa1111_dev *dev)
writel_relaxed(PCCR_S0_FLT | PCCR_S1_FLT, base + PCCR);
ret = -ENODEV;
-#ifdef CONFIG_SA1100_BADGE4
- if (machine_is_badge4())
- ret = pcmcia_badge4_init(dev);
-#endif
#ifdef CONFIG_SA1100_JORNADA720
if (machine_is_jornada720())
ret = pcmcia_jornada720_init(dev);
@@ -125,10 +125,7 @@ static int sa1111_start_hc(struct sa1111_dev *dev)
dev_dbg(&dev->dev, "starting SA-1111 OHCI USB Controller\n");
- if (machine_is_xp860() ||
- machine_is_assabet() ||
- machine_is_pfs168() ||
- machine_is_badge4())
+ if (machine_is_assabet())
usb_rst = USB_RESET_PWRSENSELOW | USB_RESET_PWRCTRLLOW;
/*
@@ -184,7 +184,6 @@
#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <mach/shannon.h>
/*
* Complain if VAR is out of range.