diff mbox series

[2/9] arm64: dts: ti: k3-j784s4-evm: Enable camera peripherals

Message ID 20240129132742.1189783-3-vaishnav.a@ti.com
State Accepted
Commit fa646b7096708db6d87b43bedefaddc7c605a9bf
Headers show
Series [1/9] arm64: dts: ti: k3-j721s2-common-proc-board: Enable camera peripherals | expand

Commit Message

Vaishnav Achath Jan. 29, 2024, 1:27 p.m. UTC 
CSI cameras are controlled using I2C. On J784S4 EVM, this is routed
to I2C-5, so enable the instance and the TCA6408 GPIO expander
on the bus.

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 25 ++++++++++++++++++++++++
 1 file changed, 25 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index f34b92acc56d..52fd7071ffd7 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -296,6 +296,13 @@  J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
 		>;
 	};
 
+	main_i2c5_pins_default: main-i2c5-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x01c, PIN_INPUT, 8) /* (AG34) MCAN15_TX.I2C5_SCL */
+			J784S4_IOPAD(0x018, PIN_INPUT, 8) /* (AK36) MCAN14_RX.I2C5_SDA */
+		>;
+	};
+
 	main_mmc1_pins_default: main-mmc1-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
@@ -760,6 +767,24 @@  exp2: gpio@22 {
 	};
 };
 
+&main_i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c5_pins_default>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	exp5: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "CSI2_EXP_RSTZ", "CSI2_EXP_A_GPIO0",
+				  "CSI2_EXP_A_GPIO1", "CSI2_EXP_A_GPIO3",
+				  "CSI2_EXP_B_GPIO1", "CSI2_EXP_B_GPIO2",
+				  "CSI2_EXP_B_GPIO3", "CSI2_EXP_B_GPIO4";
+	};
+};
+
 &main_sdhci0 {
 	bootph-all;
 	/* eMMC */