diff mbox series

[v2,7/7] arm64: dts: qcom: aim300: add AIM300 AIoT

Message ID 20231207092801.7506-8-quic_tengfan@quicinc.com
State Superseded
Headers show
Series [v2,1/7] dt-bindings: arm: qcom: Document qcs8550 SoC and board | expand

Commit Message

Tengfei Fan Dec. 7, 2023, 9:28 a.m. UTC
Add AIM300 AIoT board DTS support, including usb, serial, PCIe, and sound
card functions support.

Co-developed-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Co-developed-by: Ziyue Zhang <quic_ziyuzhan@quicinc.com>
Signed-off-by: Ziyue Zhang <quic_ziyuzhan@quicinc.com>
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/qcs8550-aim300-aiot.dts     | 579 ++++++++++++++++++
 2 files changed, 580 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts

Comments

Krzysztof Kozlowski Dec. 13, 2023, 7:38 p.m. UTC | #1
On 13/12/2023 20:01, Konrad Dybcio wrote:
> 
> 
> On 12/13/23 15:04, Krzysztof Kozlowski wrote:
>> On 11/12/2023 11:33, Krzysztof Kozlowski wrote:
>>>> @@ -0,0 +1,579 @@
>>>> +// SPDX-License-Identifier: BSD-3-Clause
>>>> +/*
>>>> + * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
>>>> + */
>>>> +
>>>> +/dts-v1/;
>>>> +
>>>> +#include <dt-bindings/leds/common.h>
>>>> +#include "qcs8550-aim300.dtsi"
>>>
>>> Which includes sm8550.dtsi thus I think this is compatible with sm8550.
>>> You even use sm8550 compatibles here, which is one more hint for that
>>> compatibility.
>>>
>>> We followed this convention for RB5, although not for QRU/QDU1000 boards.
>>>
>>> Anyway, if you add here new SoC compatible, I would expect to see new
>>> SoC DTSI.
>>>
>>> I don't have in my notes any previous consensus or decision in these
>>> matters, so let's discuss now.
>>> +CC few Linaro folks
>>
>> After some talks, the idea is to create qcs8550.dtsi, which will include
>> sm8550.dtsi, and add top level compatible for qcs8550 using sm8550 fallback.
> To the board device tree? Otherwise it'll get overwritten.

Could be both, to serve as a guideline for future DTS, but in general
yes, to the board DTS.

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 51335f08a742..779a4305a8b5 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -92,6 +92,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= qcm6490-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-rb3gen2.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qdu1000-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb2210-rb1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb4210-rb2.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts b/arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts
new file mode 100644
index 000000000000..099f28b86559
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-aim300-aiot.dts
@@ -0,0 +1,579 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "qcs8550-aim300.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. QCS8550 AIM300 AIOT";
+	compatible = "qcom,qcs8550-aim300-aiot", "qcom,qcs8550-aim300", "qcom,qcs8550";
+
+	aliases {
+		serial0 = &uart7;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wcd_default>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
+							  500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+
+		#sound-dai-cells = <1>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&volume_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			debounce-interval = <15>;
+			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&redriver_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_sbu: endpoint {
+						remote-endpoint = <&fsa4480_sbu_mux>;
+					};
+				};
+			};
+		};
+	};
+
+	sound {
+		compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
+		model = "AIM300-AIOT";
+		audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
+				"SpkrRight IN", "WSA_SPK2 OUT",
+				"IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"VA DMIC0", "MIC BIAS1",
+				"VA DMIC1", "MIC BIAS1",
+				"VA DMIC2", "MIC BIAS3",
+				"TX DMIC0", "MIC BIAS1",
+				"TX DMIC1", "MIC BIAS2",
+				"TX DMIC2", "MIC BIAS3",
+				"TX SWR_ADC1", "ADC2_OUTPUT";
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 0>, <&lpass_txmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&north_spkr>, <&south_spkr>,
+					    <&swr0 0>, <&lpass_wsamacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+};
+
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&i2c_hub_2 {
+	status = "okay";
+
+	typec-mux@42 {
+		compatible = "fcs,fsa4480";
+		reg = <0x42>;
+
+		vcc-supply = <&vreg_bob1>;
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			fsa4480_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_sbu>;
+			};
+		};
+	};
+
+	typec-retimer@1c {
+		compatible = "onnn,nb7vpq904m";
+		reg = <0x1c>;
+
+		vcc-supply = <&vreg_l15b_1p8>;
+
+		orientation-switch;
+		retimer-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				redriver_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				redriver_ss_in: endpoint {
+					data-lanes = <3 2 1 0>;
+					remote-endpoint = <&usb_dp_qmpphy_out>;
+				};
+			};
+		};
+	};
+};
+
+&gcc {
+	clocks = <&bi_tcxo_div2>, <&sleep_clk>,
+		 <0>,
+		 <&pcie1_phy>,
+		 <0>,
+		 <&ufs_mem_phy 0>,
+		 <&ufs_mem_phy 1>,
+		 <&ufs_mem_phy 2>,
+		 <&usb_dp_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
+};
+
+&lpass_tlmm {
+	spkr_1_sd_n_active: spkr-1-sd-n-active-state {
+		pins = "gpio17";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	spkr_2_sd_n_active: spkr-2-sd-n-active-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+	remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+};
+
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l3e_1p2>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "visionox,vtdr6130";
+		reg = <0>;
+
+		pinctrl-0 = <&dsi_active>, <&te_active>;
+		pinctrl-1 = <&dsi_suspend>, <&te_suspend>;
+		pinctrl-names = "default", "sleep";
+
+		reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+		vci-supply = <&vreg_l13b_3p0>;
+		vdd-supply = <&vreg_l11b_1p2>;
+		vddio-supply = <&vreg_l12b_1p8>;
+
+		port {
+			panel0_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel0_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l1e_0p88>;
+	status = "okay";
+};
+
+&pcie_1_phy_aux_clk {
+	clock-frequency = <1000>;
+};
+
+&pcie1 {
+	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-0 = <&pcie1_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l3c_0p9>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	vdda-qref-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
+&pm8550_flash {
+	status = "okay";
+
+	led-0 {
+		function = LED_FUNCTION_FLASH;
+		color = <LED_COLOR_ID_YELLOW>;
+		flash-max-microamp = <2000000>;
+		flash-max-timeout-us = <1280000>;
+		function-enumerator = <0>;
+		led-sources = <1>, <4>;
+		led-max-microamp = <500000>;
+	};
+
+	led-1 {
+		function = LED_FUNCTION_FLASH;
+		color = <LED_COLOR_ID_WHITE>;
+		flash-max-microamp = <2000000>;
+		flash-max-timeout-us = <1280000>;
+		function-enumerator = <1>;
+		led-sources = <2>, <3>;
+		led-max-microamp = <500000>;
+	};
+};
+
+&pm8550_gpios {
+	volume_up_n: volume-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pm8550_pwm {
+	status = "okay";
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@1 {
+			reg = <1>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@3 {
+			reg = <3>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+};
+
+&pm8550b_eusb2_repeater {
+	vdd18-supply = <&vreg_l15b_1p8>;
+	vdd3-supply = <&vreg_l5b_3p1>;
+};
+
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&swr0 {
+	status = "okay";
+
+	/* WSA8845, Speaker North */
+	north_spkr: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		pinctrl-0 = <&spkr_1_sd_n_active>;
+		pinctrl-names = "default";
+		powerdown-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l3g_1p2>;
+	};
+
+	/* WSA8845, Speaker South */
+	south_spkr: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		pinctrl-0 = <&spkr_2_sd_n_active>;
+		pinctrl-names = "default";
+		powerdown-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l3g_1p2>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	/* WCD9385 RX */
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9385 TX */
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <1 1 2 3>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <32 8>;
+
+	dsi_active: dsi-active-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	dsi_suspend: dsi-suspend-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	te_active: te-active-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	te_suspend: te-suspend-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio108";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+	remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
+};
+
+&usb_1_hsphy {
+	phys = <&pm8550b_eusb2_repeater>;
+
+	vdd-supply = <&vreg_l1e_0p88>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3f_0p88>;
+
+	orientation-switch;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy_dp_in {
+	remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&redriver_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_dwc3_ss>;
+};
+
+&xo_board {
+	clock-frequency = <76800000>;
+};