diff mbox series

[v2,4/4] clk: Add Ingenic JZ4755 CGU driver

Message ID 20221016150110.3020451-5-lis8215@gmail.com
State Superseded
Headers show
Series Add Ingenic JZ4755 CGU driver | expand

Commit Message

Siarhei Volkau Oct. 16, 2022, 3:01 p.m. UTC 
Add support for the clocks provided by the CGU in the Ingenic JZ4755
SoC.

Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
---
 drivers/clk/ingenic/Kconfig      |  10 +
 drivers/clk/ingenic/Makefile     |   1 +
 drivers/clk/ingenic/jz4755-cgu.c | 350 +++++++++++++++++++++++++++++++
 3 files changed, 361 insertions(+)
 create mode 100644 drivers/clk/ingenic/jz4755-cgu.c

Comments

Siarhei Volkau Oct. 17, 2022, 6:07 p.m. UTC | #1 
пн, 17 окт. 2022 г. в 20:24, Paul Cercueil <paul@crapouillou.net>:
>
>
>
> Le lun., oct. 17 2022 at 20:10:56 +0300, Siarhei Volkau
> <lis8215@gmail.com> a écrit :
> > пн, 17 окт. 2022 г. в 12:24, Paul Cercueil
> > <paul@crapouillou.net>:
> >
> >>  > +     [JZ4755_CLK_AIC] = {
> >>  > +             "aic", CGU_CLK_GATE,
> >>  > +             .parents = { JZ4755_CLK_I2S, -1, -1, -1 },
> >>
> >>  Wrong parent here, should be JZ4755_CLK_EXT_HALF.
> >
> > I don't  agree, see Figure 20-13 in the JZ4755 PM.
>
> 20-13 describes the I2S clock, no?

See 20.4.9 Serial Audio Clocks and Sampling Frequencies.
It stated that: "For internal CODEC ... CODEC needs a 12MHz
clock from CPM called SYS_CLK ...", but SYS_CLK is described
only in the I2S Controller section. I assume it is the same clock.

>
> AIC clock's parent is EXT/2 according to the diagram in 8.2.2.
>

It's a bit cryptic manual, who knows how it's done in the HW.
I observed that codec runs on a desired sample rate only when PLL
equals 432 or 216 MHz, but SYS_CLK is definitely configured to be
12MHz - from EXTCLK. On other PLL frequencies it is lower by
2-4% than expected. That isn't observed on JZ4725B.

> >>  Well it would be good to know...
> >
> > Indeed, I will try to figure it out.
>
> Cheers,
> -Paul
>
>
diff mbox series

Patch

diff --git a/drivers/clk/ingenic/Kconfig b/drivers/clk/ingenic/Kconfig
index 898f1bc47..f80ac4f29 100644
--- a/drivers/clk/ingenic/Kconfig
+++ b/drivers/clk/ingenic/Kconfig
@@ -15,6 +15,16 @@  config INGENIC_CGU_JZ4740
 
 	  If building for a JZ4740 SoC, you want to say Y here.
 
+config INGENIC_CGU_JZ4755
+	bool "Ingenic JZ4755 CGU driver"
+	default MACH_JZ4755
+	select INGENIC_CGU_COMMON
+	help
+	  Support the clocks provided by the CGU hardware on Ingenic JZ4755
+	  and compatible SoCs.
+
+	  If building for a JZ4755 SoC, you want to say Y here.
+
 config INGENIC_CGU_JZ4725B
 	bool "Ingenic JZ4725B CGU driver"
 	default MACH_JZ4725B
diff --git a/drivers/clk/ingenic/Makefile b/drivers/clk/ingenic/Makefile
index 9edfaf461..81d8e23c2 100644
--- a/drivers/clk/ingenic/Makefile
+++ b/drivers/clk/ingenic/Makefile
@@ -1,6 +1,7 @@ 
 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_INGENIC_CGU_COMMON)	+= cgu.o pm.o
 obj-$(CONFIG_INGENIC_CGU_JZ4740)	+= jz4740-cgu.o
+obj-$(CONFIG_INGENIC_CGU_JZ4755)	+= jz4755-cgu.o
 obj-$(CONFIG_INGENIC_CGU_JZ4725B)	+= jz4725b-cgu.o
 obj-$(CONFIG_INGENIC_CGU_JZ4760)	+= jz4760-cgu.o
 obj-$(CONFIG_INGENIC_CGU_JZ4770)	+= jz4770-cgu.o
diff --git a/drivers/clk/ingenic/jz4755-cgu.c b/drivers/clk/ingenic/jz4755-cgu.c
new file mode 100644
index 000000000..16728546a
--- /dev/null
+++ b/drivers/clk/ingenic/jz4755-cgu.c
@@ -0,0 +1,350 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Ingenic JZ4755 SoC CGU driver
+ * Heavily based on JZ4725b CGU driver
+ *
+ * Copyright (C) 2022 Siarhei Volkau
+ * Author: Siarhei Volkau <lis8215@gmail.com>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/of.h>
+
+#include <dt-bindings/clock/ingenic,jz4755-cgu.h>
+
+#include "cgu.h"
+#include "pm.h"
+
+/* CGU register offsets */
+#define CGU_REG_CPCCR		0x00
+#define CGU_REG_LCR		0x04
+#define CGU_REG_CPPCR		0x10
+#define CGU_REG_CLKGR		0x20
+#define CGU_REG_OPCR		0x24
+#define CGU_REG_I2SCDR		0x60
+#define CGU_REG_LPCDR		0x64
+#define CGU_REG_MSCCDR		0x68
+#define CGU_REG_SSICDR		0x74
+#define CGU_REG_CIMCDR		0x7C
+
+/* bits within the LCR register */
+#define LCR_SLEEP		BIT(0)
+
+static struct ingenic_cgu *cgu;
+
+static const s8 pll_od_encoding[4] = {
+	0x0, 0x1, -1, 0x3,
+};
+
+static const u8 jz4755_cgu_cpccr_div_table[] = {
+	1, 2, 3, 4, 6, 8,
+};
+
+static const u8 jz4755_cgu_pll_half_div_table[] = {
+	2, 1,
+};
+
+static const struct ingenic_cgu_clk_info jz4755_cgu_clocks[] = {
+
+	/* External clocks */
+
+	[JZ4755_CLK_EXT] = { "ext", CGU_CLK_EXT },
+	[JZ4755_CLK_OSC32K] = { "osc32k", CGU_CLK_EXT },
+
+	[JZ4755_CLK_PLL] = {
+		"pll", CGU_CLK_PLL,
+		.parents = { JZ4755_CLK_EXT, -1, -1, -1 },
+		.pll = {
+			.reg = CGU_REG_CPPCR,
+			.rate_multiplier = 1,
+			.m_shift = 23,
+			.m_bits = 9,
+			.m_offset = 2,
+			.n_shift = 18,
+			.n_bits = 5,
+			.n_offset = 2,
+			.od_shift = 16,
+			.od_bits = 2,
+			.od_max = 4,
+			.od_encoding = pll_od_encoding,
+			.stable_bit = 10,
+			.bypass_reg = CGU_REG_CPPCR,
+			.bypass_bit = 9,
+			.enable_bit = 8,
+		},
+	},
+
+	/* Muxes & dividers */
+
+	[JZ4755_CLK_PLL_HALF] = {
+		"pll half", CGU_CLK_DIV,
+		.parents = { JZ4755_CLK_PLL, -1, -1, -1 },
+		.div = {
+			CGU_REG_CPCCR, 21, 1, 1, -1, -1, -1, 0,
+			jz4755_cgu_pll_half_div_table,
+		},
+	},
+
+	[JZ4755_CLK_EXT_HALF] = {
+		"ext half", CGU_CLK_DIV,
+		.parents = { JZ4755_CLK_EXT, -1, -1, -1 },
+		.div = {
+			CGU_REG_CPCCR, 30, 1, 1, -1, -1, -1, 0,
+			NULL,
+		},
+	},
+
+	[JZ4755_CLK_CCLK] = {
+		"cclk", CGU_CLK_DIV,
+		.parents = { JZ4755_CLK_PLL, -1, -1, -1 },
+		.div = {
+			CGU_REG_CPCCR, 0, 1, 4, 22, -1, -1, 0,
+			jz4755_cgu_cpccr_div_table,
+		},
+	},
+
+	[JZ4755_CLK_H0CLK] = {
+		"hclk", CGU_CLK_DIV,
+		.parents = { JZ4755_CLK_PLL, -1, -1, -1 },
+		.div = {
+			CGU_REG_CPCCR, 4, 1, 4, 22, -1, -1, 0,
+			jz4755_cgu_cpccr_div_table,
+		},
+	},
+
+	[JZ4755_CLK_PCLK] = {
+		"pclk", CGU_CLK_DIV,
+		.parents = { JZ4755_CLK_PLL, -1, -1, -1 },
+		.div = {
+			CGU_REG_CPCCR, 8, 1, 4, 22, -1, -1, 0,
+			jz4755_cgu_cpccr_div_table,
+		},
+	},
+
+	[JZ4755_CLK_MCLK] = {
+		"mclk", CGU_CLK_DIV,
+		.parents = { JZ4755_CLK_PLL, -1, -1, -1 },
+		.div = {
+			CGU_REG_CPCCR, 12, 1, 4, 22, -1, -1, 0,
+			jz4755_cgu_cpccr_div_table,
+		},
+	},
+
+	[JZ4755_CLK_H1CLK] = {
+		"h1clk", CGU_CLK_DIV,
+		.parents = { JZ4755_CLK_PLL, -1, -1, -1 },
+		.div = {
+			CGU_REG_CPCCR, 16, 1, 4, 22, -1, -1, 0,
+			jz4755_cgu_cpccr_div_table,
+		},
+	},
+
+	[JZ4755_CLK_UDC] = {
+		"udc", CGU_CLK_MUX | CGU_CLK_DIV | CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT_HALF, JZ4755_CLK_PLL_HALF, -1, -1 },
+		.mux = { CGU_REG_CPCCR, 29, 1 },
+		.div = { CGU_REG_CPCCR, 23, 1, 6, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 10 },
+	},
+
+	[JZ4755_CLK_LCD] = {
+		"lcd", CGU_CLK_DIV | CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_PLL_HALF, -1, -1, -1 },
+		.div = { CGU_REG_LPCDR, 0, 1, 11, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 9 },
+	},
+
+	[JZ4755_CLK_MMC] = {
+		"mmc", CGU_CLK_DIV,
+		.parents = { JZ4755_CLK_PLL_HALF, -1, -1, -1 },
+		.div = { CGU_REG_MSCCDR, 0, 1, 5, -1, -1, -1 },
+	},
+
+	[JZ4755_CLK_I2S] = {
+		"i2s", CGU_CLK_MUX | CGU_CLK_DIV,
+		.parents = { JZ4755_CLK_EXT_HALF, JZ4755_CLK_PLL_HALF, -1, -1 },
+		.mux = { CGU_REG_CPCCR, 31, 1 },
+		.div = { CGU_REG_I2SCDR, 0, 1, 9, -1, -1, -1 },
+	},
+
+	[JZ4755_CLK_SPI] = {
+		"spi", CGU_CLK_DIV | CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_PLL_HALF, -1, -1, -1 },
+		.div = { CGU_REG_SSICDR, 0, 1, 4, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 4 },
+	},
+
+	[JZ4755_CLK_TVE] = {
+		"tve", CGU_CLK_MUX | CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_LCD, JZ4755_CLK_EXT, -1, -1 },
+		.mux = { CGU_REG_LPCDR, 31, 1 },
+		.gate = { CGU_REG_CLKGR, 18 },
+	},
+
+	[JZ4755_CLK_RTC] = {
+		"rtc", CGU_CLK_MUX | CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT512, JZ4755_CLK_OSC32K, -1, -1 },
+		.mux = { CGU_REG_OPCR, 2, 1},
+		.gate = { CGU_REG_CLKGR, 2 },
+	},
+
+	[JZ4755_CLK_CIM] = {
+		"cim", CGU_CLK_DIV | CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_PLL_HALF, -1, -1, -1 },
+		.div = { CGU_REG_CIMCDR, 0, 1, 8, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 8 },
+	},
+
+	/* Gate-only clocks */
+
+	[JZ4755_CLK_UART0] = {
+		"uart0", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT_HALF, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 0 },
+	},
+
+	[JZ4755_CLK_UART1] = {
+		"uart1", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT_HALF, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 14 },
+	},
+
+	[JZ4755_CLK_UART2] = {
+		"uart2", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT_HALF, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 15 },
+	},
+
+	[JZ4755_CLK_ADC] = {
+		"adc", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT_HALF, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 7 },
+	},
+
+	[JZ4755_CLK_AIC] = {
+		"aic", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_I2S, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 5 },
+	},
+
+	[JZ4755_CLK_I2C] = {
+		"i2c", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT_HALF, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 3 },
+	},
+
+	[JZ4755_CLK_BCH] = {
+		"bch", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_MCLK/* not sure */, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 11 },
+	},
+
+	[JZ4755_CLK_TCU] = {
+		"tcu", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 1 },
+	},
+
+	[JZ4755_CLK_DMA] = {
+		"dma", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_PCLK, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 12 },
+	},
+
+	[JZ4755_CLK_MMC0] = {
+		"mmc0", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_MMC, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 6 },
+	},
+
+	[JZ4755_CLK_MMC1] = {
+		"mmc1", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_MMC, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 16 },
+	},
+
+	[JZ4755_CLK_AUX_CPU] = {
+		"aux_cpu", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_H1CLK, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 24 },
+	},
+
+	[JZ4755_CLK_AHB1] = {
+		"ahb1", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_H1CLK, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 23 },
+	},
+
+	[JZ4755_CLK_IDCT] = {
+		"idct", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_H1CLK, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 22 },
+	},
+
+	[JZ4755_CLK_DB] = {
+		"db", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_H1CLK, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 21 },
+	},
+
+	[JZ4755_CLK_ME] = {
+		"me", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_H1CLK, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 20 },
+	},
+
+	[JZ4755_CLK_MC] = {
+		"mc", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_H1CLK, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 19 },
+	},
+
+	[JZ4755_CLK_TSSI] = {
+		"tssi", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT_HALF/* not sure */, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 17 },
+	},
+
+	[JZ4755_CLK_IPU] = {
+		"ipu", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_PLL_HALF/* not sure */, -1, -1, -1 },
+		.gate = { CGU_REG_CLKGR, 13 },
+	},
+
+	[JZ4755_CLK_EXT512] = {
+		"ext/512", CGU_CLK_FIXDIV,
+		.parents = { JZ4755_CLK_EXT },
+
+		/* JZ4725b doc calls it EXT512, but it seems to be /256...
+		 * Not sure if it applied to JZ4755 too, and which actual
+		 * source is used EXT or EXT_HALF
+		 */
+		.fixdiv = { 256 },
+	},
+
+	[JZ4755_CLK_UDC_PHY] = {
+		"udc_phy", CGU_CLK_GATE,
+		.parents = { JZ4755_CLK_EXT_HALF, -1, -1, -1 },
+		.gate = { CGU_REG_OPCR, 6, true },
+	},
+};
+
+static void __init jz4755_cgu_init(struct device_node *np)
+{
+	int retval;
+
+	cgu = ingenic_cgu_new(jz4755_cgu_clocks,
+			      ARRAY_SIZE(jz4755_cgu_clocks), np);
+	if (!cgu) {
+		pr_err("%s: failed to initialise CGU\n", __func__);
+		return;
+	}
+
+	retval = ingenic_cgu_register_clocks(cgu);
+	if (retval)
+		pr_err("%s: failed to register CGU Clocks\n", __func__);
+
+	ingenic_cgu_register_syscore_ops(cgu);
+}
+CLK_OF_DECLARE_DRIVER(jz4755_cgu, "ingenic,jz4755-cgu", jz4755_cgu_init);