@@ -313,6 +313,49 @@ i2c5: i2c@4c006000 {
status = "disabled";
};
+ adc_2: adc@48004000 {
+ compatible = "st,stm32mp13-adc-core";
+ reg = <0x48004000 0x400>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc ADC2>, <&rcc ADC2_K>;
+ clock-names = "bus", "adc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ adc2: adc@0 {
+ compatible = "st,stm32mp13-adc";
+ #io-channel-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+ interrupt-parent = <&adc_2>;
+ interrupts = <0>;
+ dmas = <&dmamux1 10 0x400 0x80000001>;
+ dma-names = "rx";
+ status = "disabled";
+
+ channel@13 {
+ reg = <13>;
+ label = "vrefint";
+ };
+ channel@14 {
+ reg = <14>;
+ label = "vddcore";
+ };
+ channel@16 {
+ reg = <16>;
+ label = "vddcpu";
+ };
+ channel@17 {
+ reg = <17>;
+ label = "vddq_ddr";
+ };
+ };
+ };
+
rcc: rcc@50000000 {
compatible = "st,stm32mp13-rcc", "syscon";
reg = <0x50000000 0x1000>;
@@ -33,5 +33,36 @@ m_can2: can@4400f000 {
bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
status = "disabled";
};
+
+ adc_1: adc@48003000 {
+ compatible = "st,stm32mp13-adc-core";
+ reg = <0x48003000 0x400>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc ADC1>, <&rcc ADC1_K>;
+ clock-names = "bus", "adc";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ adc1: adc@0 {
+ compatible = "st,stm32mp13-adc";
+ #io-channel-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+ interrupt-parent = <&adc_1>;
+ interrupts = <0>;
+ dmas = <&dmamux1 9 0x400 0x80000001>;
+ dma-names = "rx";
+ status = "disabled";
+
+ channel@18 {
+ reg = <18>;
+ label = "vrefint";
+ };
+ };
+ };
};
};
Add ADC1 and ADC2 support to STM32MP13 SoC family. The STM32MP131 provides only ADC2, while other STM32MP13 SoCs provide both ADC1 and ADC2. Internal channels support limitations: - VREFINT internal channel requires calibration data from OTP memory. The nvmem properties used to access OTP are not defined for time being, as OTP support is not yet enabled. - VBAT internal channel is not defined by default in SoC DT, and has be defined in board DT when needed, instead. This avoids unwanted current consumption on battery, when ADC conversions are performed on any other channels. Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com> --- arch/arm/boot/dts/stm32mp131.dtsi | 43 +++++++++++++++++++++++++++++++ arch/arm/boot/dts/stm32mp133.dtsi | 31 ++++++++++++++++++++++ 2 files changed, 74 insertions(+)