[v5,4/8] phy: fsl: Add Lynx 10G SerDes driver

diff --git a/Documentation/driver-api/phy/index.rst b/Documentation/driver-api/phy/index.rst
index 69ba1216de72..c9b7a4698dab 100644
--- a/Documentation/driver-api/phy/index.rst
+++ b/Documentation/driver-api/phy/index.rst
@@ -7,6 +7,7 @@  Generic PHY Framework
 .. toctree::
 
    phy
+   lynx_10g
    samsung-usb2
 
 .. only::  subproject and html
diff --git a/Documentation/driver-api/phy/lynx_10g.rst b/Documentation/driver-api/phy/lynx_10g.rst
new file mode 100644
index 000000000000..6e85dcd8fd71
--- /dev/null
+++ b/Documentation/driver-api/phy/lynx_10g.rst
@@ -0,0 +1,66 @@ 
+.. SPDX-License-Identifier: GPL-2.0
+
+===========================
+Lynx 10G Phy (QorIQ SerDes)
+===========================
+
+Using this phy
+--------------
+
+The general order of calls should be::
+
+    [devm_][of_]phy_get()
+    phy_init()
+    phy_power_on()
+    phy_set_mode[_ext]()
+    ...
+    phy_power_off()
+    phy_exit()
+    [[of_]phy_put()]
+
+:c:func:`phy_get` just gets (or creates) a new :c:type:`phy` with the lanes
+described in the phandle. :c:func:`phy_init` is what actually reserves the
+lanes for use. Unlike some other drivers, when the phy is created, there is no
+default protocol. :c:func:`phy_set_mode <phy_set_mode_ext>` must be called in
+order to set the protocol.
+
+Supporting SoCs
+---------------
+
+Each new SoC needs a :c:type:`struct lynx_conf <lynx_conf>`, containing the
+number of lanes in each device, the endianness of the device, and the helper
+functions to use when selecting protocol controllers. For example, the
+configuration for the LS1046A is::
+
+    static const struct lynx_cfg ls1046a_cfg = {
+        .lanes = 4,
+        .endian = REGMAP_ENDIAN_BIG,
+        .mode_conflict = lynx_ls_mode_conflict,
+        .mode_apply = lynx_ls_mode_apply,
+        .mode_init = lynx_ls_mode_init,
+    };
+
+In addition, you will need to add a device node as documented in
+``Documentation/devicetree/bindings/phy/fsl,lynx-10g.yaml``.  This lets the
+driver know which lanes are available to configure.
+
+Supporting Protocols
+--------------------
+
+Each protocol is a combination of values which must be programmed into the lane
+registers. To add a new protocol, first add it to :c:type:`enum lynx_protocol
+<lynx_protocol>`. Add a new entry to `lynx_proto_params`, and populate the
+appropriate fields. Modify `lynx_lookup_proto` to map the :c:type:`enum
+phy_mode <phy_mode>` to :c:type:`enum lynx_protocol <lynx_protocol>`. Update
+the ``mode_conflict``, ``mode_apply``, and ``mode_init`` helpers are updated to
+support your protocol.
+
+You may need to modify :c:func:`lynx_set_mode` in order to support your
+protocol. This can happen when you have added members to :c:type:`struct
+lynx_proto_params <lynx_proto_params>`. It can also happen if you have specific
+clocking requirements, or protocol-specific registers to program.
+
+Internal API Reference
+----------------------
+
+.. kernel-doc:: drivers/phy/freescale/phy-fsl-lynx-10g.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 589517372408..cd9a8683ebe2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11978,6 +11978,13 @@  S:	Maintained
 W:	http://linux-test-project.github.io/
 T:	git git://github.com/linux-test-project/ltp.git
 
+LYNX 10G SERDES DRIVER
+M:	Sean Anderson <sean.anderson@seco.com>
+S:	Maintained
+F:	Documentation/driver-api/phy/lynx_10g.rst
+F:	drivers/phy/freescale/phy-fsl-lynx-10g.c
+F:	include/dt-bindings/clock/fsl,lynx-10g.h
+
 LYNX 28G SERDES PHY DRIVER
 M:	Ioana Ciornei <ioana.ciornei@nxp.com>
 L:	netdev@vger.kernel.org
diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
index 853958fb2c06..6820505367cb 100644
--- a/drivers/phy/freescale/Kconfig
+++ b/drivers/phy/freescale/Kconfig
@@ -47,3 +47,22 @@  config PHY_FSL_LYNX_28G
 	  found on NXP's Layerscape platforms such as LX2160A.
 	  Used to change the protocol running on SerDes lanes at runtime.
 	  Only useful for a restricted set of Ethernet protocols.
+
+config PHY_FSL_LYNX_10G
+	tristate "Freescale Layerscale Lynx 10G SerDes support"
+	select GENERIC_PHY
+	select REGMAP_MMIO
+	help
+	  This adds support for the Lynx "SerDes" devices found on various QorIQ
+	  SoCs. There may be up to four SerDes devices on each SoC, and each
+	  device supports up to eight lanes. The SerDes is configured by default
+	  by the RCW, but this module is necessary in order to support dynamic
+	  reconfiguration (such as to support 1G and 10G ethernet on the same
+	  interface). The hardware supports a variety of protocols, including
+	  Ethernet, SATA, PCIe, and more exotic links such as Interlaken and
+	  Aurora. This driver only supports Ethernet, but it will try not to
+	  touch lanes configured for other protocols.
+
+	  If you have a QorIQ processor and want to dynamically reconfigure your
+	  SerDes, say Y. If this driver is compiled as a module, it will be
+	  named phy-fsl-lynx-10g-drv.
diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
index cedb328bc4d2..1f18936507e0 100644
--- a/drivers/phy/freescale/Makefile
+++ b/drivers/phy/freescale/Makefile
@@ -3,4 +3,7 @@  obj-$(CONFIG_PHY_FSL_IMX8MQ_USB)	+= phy-fsl-imx8mq-usb.o
 obj-$(CONFIG_PHY_MIXEL_LVDS_PHY)	+= phy-fsl-imx8qm-lvds-phy.o
 obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY)	+= phy-fsl-imx8-mipi-dphy.o
 obj-$(CONFIG_PHY_FSL_IMX8M_PCIE)	+= phy-fsl-imx8m-pcie.o
+phy-fsl-lynx-10g-drv-y			+= phy-fsl-lynx-10g.o
+phy-fsl-lynx-10g-drv-y			+= phy-fsl-lynx-10g-clk.o
+obj-$(CONFIG_PHY_FSL_LYNX_10G)		+= phy-fsl-lynx-10g-drv.o
 obj-$(CONFIG_PHY_FSL_LYNX_28G)		+= phy-fsl-lynx-28g.o
diff --git a/drivers/phy/freescale/lynx-10g.h b/drivers/phy/freescale/lynx-10g.h
new file mode 100644
index 000000000000..75d9353a867b
--- /dev/null
+++ b/drivers/phy/freescale/lynx-10g.h
@@ -0,0 +1,16 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Sean Anderson <sean.anderson@seco.com>
+ */
+
+#ifndef LYNX_10G
+#define LYNX_10G
+
+struct clk;
+struct device;
+struct regmap;
+
+int lynx_clks_init(struct device *dev, struct regmap *regmap,
+		   struct clk *plls[2], struct clk *ex_dlys[2]);
+
+#endif /* LYNX 10G */
diff --git a/drivers/phy/freescale/phy-fsl-lynx-10g-clk.c b/drivers/phy/freescale/phy-fsl-lynx-10g-clk.c
new file mode 100644
index 000000000000..adb5f4d0a4d2
--- /dev/null
+++ b/drivers/phy/freescale/phy-fsl-lynx-10g-clk.c
@@ -0,0 +1,501 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Sean Anderson <sean.anderson@seco.com>
+ *
+ * This file contains the implementation for the PLLs found on Lynx 10G phys.
+ *
+ * XXX: The VCO rate of the PLLs can exceed ~4GHz, which is the maximum rate
+ * expressable in an unsigned long. To work around this, rates are specified in
+ * kHz. This is as if there was a division by 1000 in the PLL.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/math64.h>
+#include <linux/regmap.h>
+#include <linux/units.h>
+#include <dt-bindings/clock/fsl,lynx-10g.h>
+
+#include "lynx-10g.h"
+
+#define PLL_STRIDE	0x20
+#define PLLa(a, off)	((a) * PLL_STRIDE + (off))
+#define PLLaRSTCTL(a)	PLLa(a, 0x00)
+#define PLLaCR0(a)	PLLa(a, 0x04)
+
+#define PLLaRSTCTL_RSTREQ	BIT(31)
+#define PLLaRSTCTL_RST_DONE	BIT(30)
+#define PLLaRSTCTL_RST_ERR	BIT(29)
+#define PLLaRSTCTL_PLLRST_B	BIT(7)
+#define PLLaRSTCTL_SDRST_B	BIT(6)
+#define PLLaRSTCTL_SDEN		BIT(5)
+
+#define PLLaRSTCTL_ENABLE_SET	(PLLaRSTCTL_RST_DONE | PLLaRSTCTL_PLLRST_B | \
+				 PLLaRSTCTL_SDRST_B | PLLaRSTCTL_SDEN)
+#define PLLaRSTCTL_ENABLE_MASK	(PLLaRSTCTL_ENABLE_SET | PLLaRSTCTL_RST_ERR)
+
+#define PLLaCR0_POFF		BIT(31)
+#define PLLaCR0_RFCLK_SEL	GENMASK(30, 28)
+#define PLLaCR0_PLL_LCK		BIT(23)
+#define PLLaCR0_FRATE_SEL	GENMASK(19, 16)
+#define PLLaCR0_DLYDIV_SEL	GENMASK(1, 0)
+
+#define PLLaCR0_DLYDIV_SEL_16		0b01
+
+/**
+ * struct lynx_clk - Driver data for the PLLs
+ * @pll: The PLL clock
+ * @ex_dly: The "PLLa_ex_dly_clk" clock
+ * @ref: Our reference clock
+ * @dev: The serdes device
+ * @regmap: Our registers
+ * @idx: Which PLL this clock is for
+ */
+struct lynx_clk {
+	struct clk_hw pll, ex_dly;
+	struct clk_hw *ref;
+	struct device *dev;
+	struct regmap *regmap;
+	unsigned int idx;
+};
+
+static u32 lynx_read(struct lynx_clk *clk, u32 reg)
+{
+	unsigned int ret = 0;
+
+	WARN_ON_ONCE(regmap_read(clk->regmap, reg, &ret));
+	return ret;
+}
+
+static void lynx_write(struct lynx_clk *clk, u32 val, u32 reg)
+{
+	WARN_ON_ONCE(regmap_write(clk->regmap, reg, val));
+}
+
+static struct lynx_clk *lynx_pll_to_clk(struct clk_hw *hw)
+{
+	return container_of(hw, struct lynx_clk, pll);
+}
+
+static struct lynx_clk *lynx_ex_dly_to_clk(struct clk_hw *hw)
+{
+	return container_of(hw, struct lynx_clk, ex_dly);
+}
+
+static void lynx_pll_stop(struct lynx_clk *clk)
+{
+	u32 rstctl;
+
+	rstctl = lynx_read(clk, PLLaRSTCTL(clk->idx));
+	rstctl &= ~PLLaRSTCTL_SDRST_B;
+	lynx_write(clk, rstctl, PLLaRSTCTL(clk->idx));
+
+	ndelay(50);
+
+	rstctl = lynx_read(clk, PLLaRSTCTL(clk->idx));
+	rstctl &= ~(PLLaRSTCTL_SDEN | PLLaRSTCTL_PLLRST_B);
+	lynx_write(clk, rstctl, PLLaRSTCTL(clk->idx));
+
+	ndelay(100);
+}
+
+static void lynx_pll_disable(struct clk_hw *hw)
+{
+	struct lynx_clk *clk = lynx_pll_to_clk(hw);
+	u32 cr0;
+
+	dev_dbg(clk->dev, "disable pll%d\n", clk->idx);
+
+	lynx_pll_stop(clk);
+
+	cr0 = lynx_read(clk, PLLaCR0(clk->idx));
+	cr0 |= PLLaCR0_POFF;
+	lynx_write(clk, cr0, PLLaCR0(clk->idx));
+}
+
+static int lynx_pll_reset(struct lynx_clk *clk)
+{
+	int ret;
+	u32 rstctl = lynx_read(clk, PLLaRSTCTL(clk->idx));
+
+	rstctl |= PLLaRSTCTL_RSTREQ;
+	lynx_write(clk, rstctl, PLLaRSTCTL(clk->idx));
+	ret = read_poll_timeout(lynx_read, rstctl,
+				rstctl & (PLLaRSTCTL_RST_DONE | PLLaRSTCTL_RST_ERR),
+				100, 5000, true, clk, PLLaRSTCTL(clk->idx));
+	if (rstctl & PLLaRSTCTL_RST_ERR)
+		ret = -EIO;
+	if (ret) {
+		dev_err(clk->dev, "pll%d reset failed\n", clk->idx);
+		return ret;
+	}
+
+	rstctl |= PLLaRSTCTL_SDEN | PLLaRSTCTL_PLLRST_B | PLLaRSTCTL_SDRST_B;
+	lynx_write(clk, rstctl, PLLaRSTCTL(clk->idx));
+	return 0;
+}
+
+static int lynx_pll_prepare(struct clk_hw *hw)
+{
+	struct lynx_clk *clk = lynx_pll_to_clk(hw);
+	u32 rstctl = lynx_read(clk, PLLaRSTCTL(clk->idx));
+	u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
+
+	/*
+	 * "Enabling" the PLL involves resetting it (and all attached lanes).
+	 * Avoid doing this if we are already enabled.
+	 */
+	if (!(cr0 & PLLaCR0_POFF) &&
+	    (rstctl & PLLaRSTCTL_ENABLE_MASK) == PLLaRSTCTL_ENABLE_SET) {
+		dev_dbg(clk->dev, "pll%d already prepared\n", clk->idx);
+		return 0;
+	}
+
+	dev_dbg(clk->dev, "prepare pll%d\n", clk->idx);
+
+	cr0 &= ~PLLaCR0_POFF;
+	lynx_write(clk, cr0, PLLaCR0(clk->idx));
+
+	return lynx_pll_reset(clk);
+}
+
+static int lynx_pll_is_enabled(struct clk_hw *hw)
+{
+	struct lynx_clk *clk = lynx_pll_to_clk(hw);
+	u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
+	bool enabled = !(cr0 & PLLaCR0_POFF);
+
+	dev_dbg(clk->dev, "pll%d %s enabled\n", clk->idx,
+		enabled ? "is" : "is not");
+
+	return enabled;
+}
+
+static const u32 rfclk_sel_map[8] = {
+	[0b000] = 100000000,
+	[0b001] = 125000000,
+	[0b010] = 156250000,
+	[0b011] = 150000000,
+};
+
+/**
+ * lynx_rfclk_to_sel() - Convert a reference clock rate to a selector
+ * @rate: The reference clock rate
+ *
+ * To allow for some variation in the reference clock rate, up to 100ppm of
+ * error is allowed.
+ *
+ * Return: An appropriate selector for @rate, or -%EINVAL.
+ */
+static int lynx_rfclk_to_sel(u32 rate)
+{
+	int ret;
+
+	for (ret = 0; ret < ARRAY_SIZE(rfclk_sel_map); ret++) {
+		u32 rfclk_rate = rfclk_sel_map[ret];
+		/* Allow an error of 100ppm */
+		u32 error = rfclk_rate / 10000;
+
+		if (rate > rfclk_rate - error && rate < rfclk_rate + error)
+			return ret;
+	}
+
+	return -EINVAL;
+}
+
+static const u32 frate_sel_map[16] = {
+	[0b0000] = 5000000,
+	[0b0101] = 3750000,
+	[0b0110] = 5156250,
+	[0b0111] = 4000000,
+	[0b1001] = 3125000,
+	[0b1010] = 3000000,
+};
+
+/**
+ * lynx_frate_to_sel() - Convert a VCO clock rate to a selector
+ * @rate_khz: The VCO frequency, in kHz
+ *
+ * Return: An appropriate selector for @rate_khz, or -%EINVAL.
+ */
+static int lynx_frate_to_sel(u32 rate_khz)
+{
+	int ret;
+
+	for (ret = 0; ret < ARRAY_SIZE(frate_sel_map); ret++)
+		if (frate_sel_map[ret] == rate_khz)
+			return ret;
+
+	return -EINVAL;
+}
+
+static u32 lynx_pll_ratio(u32 frate_sel, u32 rfclk_sel)
+{
+	u64 frate;
+	u32 rfclk, error, ratio;
+
+	frate = frate_sel_map[frate_sel] * (u64)HZ_PER_KHZ;
+	rfclk = rfclk_sel_map[rfclk_sel];
+
+	if (!frate || !rfclk)
+		return 0;
+
+	ratio = div_u64_rem(frate, rfclk, &error);
+	if (!error)
+		return ratio;
+	return 0;
+}
+
+static unsigned long lynx_pll_recalc_rate(struct clk_hw *hw,
+					  unsigned long parent_rate)
+{
+	struct lynx_clk *clk = lynx_pll_to_clk(hw);
+	u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
+	u32 frate_sel = FIELD_GET(PLLaCR0_FRATE_SEL, cr0);
+	u32 rfclk_sel = FIELD_GET(PLLaCR0_RFCLK_SEL, cr0);
+	u32 ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
+	unsigned long ret;
+
+	/* Ensure that the parent matches our rfclk selector */
+	if (rfclk_sel == lynx_rfclk_to_sel(parent_rate))
+		ret = mult_frac(parent_rate, ratio, HZ_PER_KHZ);
+	else
+		ret = 0;
+
+	dev_dbg(clk->dev, "recalc pll%d new=%llu parent=%lu\n", clk->idx,
+		(u64)ret * HZ_PER_KHZ, parent_rate);
+	return ret;
+}
+
+static long lynx_pll_round_rate(struct clk_hw *hw, unsigned long rate_khz,
+				unsigned long *parent_rate)
+{
+	int frate_sel, rfclk_sel;
+	struct lynx_clk *clk = lynx_pll_to_clk(hw);
+	u32 ratio;
+
+	dev_dbg(clk->dev, "round pll%d new=%llu parent=%lu\n", clk->idx,
+		(u64)rate_khz * HZ_PER_KHZ, *parent_rate);
+
+	frate_sel = lynx_frate_to_sel(rate_khz);
+	if (frate_sel < 0)
+		return frate_sel;
+
+	/* Try the current parent rate */
+	rfclk_sel = lynx_rfclk_to_sel(*parent_rate);
+	if (rfclk_sel >= 0) {
+		ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
+		if (ratio)
+			return mult_frac(*parent_rate, ratio, HZ_PER_KHZ);
+	}
+
+	/* Try all possible parent rates */
+	for (rfclk_sel = 0;
+	     rfclk_sel < ARRAY_SIZE(rfclk_sel_map);
+	     rfclk_sel++) {
+		unsigned long new_parent_rate;
+
+		ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
+		if (!ratio)
+			continue;
+
+		/* Ensure the reference clock can produce this rate */
+		new_parent_rate = rfclk_sel_map[rfclk_sel];
+		new_parent_rate = clk_hw_round_rate(clk->ref, new_parent_rate);
+		if (rfclk_sel != lynx_rfclk_to_sel(new_parent_rate))
+			continue;
+
+		*parent_rate = new_parent_rate;
+		return mult_frac(new_parent_rate, ratio, HZ_PER_KHZ);
+	}
+
+	return -EINVAL;
+}
+
+static int lynx_pll_set_rate(struct clk_hw *hw, unsigned long rate_khz,
+			   unsigned long parent_rate)
+{
+	int frate_sel, rfclk_sel;
+	struct lynx_clk *clk = lynx_pll_to_clk(hw);
+	u32 ratio, cr0 = lynx_read(clk, PLLaCR0(clk->idx));
+
+	dev_dbg(clk->dev, "set rate pll%d new=%llu parent=%lu\n", clk->idx,
+		(u64)rate_khz * HZ_PER_KHZ, parent_rate);
+
+	frate_sel = lynx_frate_to_sel(rate_khz);
+	if (frate_sel < 0)
+		return frate_sel;
+
+	rfclk_sel = lynx_rfclk_to_sel(parent_rate);
+	if (rfclk_sel < 0)
+		return rfclk_sel;
+
+	ratio = lynx_pll_ratio(frate_sel, rfclk_sel);
+	if (!ratio)
+		return -EINVAL;
+
+	lynx_pll_stop(clk);
+	cr0 &= ~(PLLaCR0_RFCLK_SEL | PLLaCR0_FRATE_SEL);
+	cr0 |= FIELD_PREP(PLLaCR0_RFCLK_SEL, rfclk_sel);
+	cr0 |= FIELD_PREP(PLLaCR0_FRATE_SEL, frate_sel);
+	lynx_write(clk, cr0, PLLaCR0(clk->idx));
+	/* Don't bother resetting if it's off */
+	if (cr0 & PLLaCR0_POFF)
+		return 0;
+	return lynx_pll_reset(clk);
+}
+
+static const struct clk_ops lynx_pll_clk_ops = {
+	.prepare = lynx_pll_prepare,
+	.disable = lynx_pll_disable,
+	.is_enabled = lynx_pll_is_enabled,
+	.recalc_rate = lynx_pll_recalc_rate,
+	.round_rate = lynx_pll_round_rate,
+	.set_rate = lynx_pll_set_rate,
+};
+
+static void lynx_ex_dly_disable(struct clk_hw *hw)
+{
+	struct lynx_clk *clk = lynx_ex_dly_to_clk(hw);
+	u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
+
+	cr0 &= ~PLLaCR0_DLYDIV_SEL;
+	lynx_write(clk, PLLaCR0(clk->idx), cr0);
+}
+
+static int lynx_ex_dly_enable(struct clk_hw *hw)
+{
+	struct lynx_clk *clk = lynx_ex_dly_to_clk(hw);
+	u32 cr0 = lynx_read(clk, PLLaCR0(clk->idx));
+
+	cr0 &= ~PLLaCR0_DLYDIV_SEL;
+	cr0 |= FIELD_PREP(PLLaCR0_DLYDIV_SEL, PLLaCR0_DLYDIV_SEL_16);
+	lynx_write(clk, PLLaCR0(clk->idx), cr0);
+	return 0;
+}
+
+static int lynx_ex_dly_is_enabled(struct clk_hw *hw)
+{
+	struct lynx_clk *clk = lynx_ex_dly_to_clk(hw);
+
+	return lynx_read(clk, PLLaCR0(clk->idx)) & PLLaCR0_DLYDIV_SEL;
+}
+
+static unsigned long lynx_ex_dly_recalc_rate(struct clk_hw *hw,
+					     unsigned long parent_rate)
+{
+	return parent_rate / 16;
+}
+
+static const struct clk_ops lynx_ex_dly_clk_ops = {
+	.enable = lynx_ex_dly_enable,
+	.disable = lynx_ex_dly_disable,
+	.is_enabled = lynx_ex_dly_is_enabled,
+	.recalc_rate = lynx_ex_dly_recalc_rate,
+};
+
+static int lynx_clk_init(struct clk_hw_onecell_data *hw_data,
+			 struct device *dev, struct regmap *regmap,
+			 unsigned int index)
+{
+	const struct clk_hw *pll_parents, *ex_dly_parents;
+	struct clk_init_data pll_init = {
+		.ops = &lynx_pll_clk_ops,
+		.parent_hws = &pll_parents,
+		.num_parents = 1,
+		.flags = CLK_GET_RATE_NOCACHE | CLK_SET_RATE_PARENT |
+			 CLK_OPS_PARENT_ENABLE,
+	};
+	struct clk_init_data ex_dly_init = {
+		.ops = &lynx_ex_dly_clk_ops,
+		.parent_hws = &ex_dly_parents,
+		.num_parents = 1,
+	};
+	struct clk *ref;
+	struct lynx_clk *clk;
+	char *ref_name;
+	int ret;
+
+	clk = devm_kzalloc(dev, sizeof(*clk), GFP_KERNEL);
+	if (!clk)
+		return -ENOMEM;
+
+	clk->dev = dev;
+	clk->regmap = regmap;
+	clk->idx = index;
+
+	ref_name = kasprintf(GFP_KERNEL, "ref%d", index);
+	pll_init.name = kasprintf(GFP_KERNEL, "%s.pll%d_khz", dev_name(dev),
+				  index);
+	ex_dly_init.name = kasprintf(GFP_KERNEL, "%s.pll%d_ex_dly_khz",
+				     dev_name(dev), index);
+	if (!ref_name || !pll_init.name || !ex_dly_init.name) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	ref = devm_clk_get(dev, ref_name);
+	if (IS_ERR(clk->ref)) {
+		ret = PTR_ERR(clk->ref);
+		dev_err_probe(dev, ret, "could not get %s\n", ref_name);
+		goto out;
+	}
+
+	clk->ref = __clk_get_hw(ref);
+	pll_parents = clk->ref;
+	clk->pll.init = &pll_init;
+	ret = devm_clk_hw_register(dev, &clk->pll);
+	if (ret) {
+		dev_err_probe(dev, ret, "could not register %s\n",
+			      pll_init.name);
+		goto out;
+	}
+
+	ex_dly_parents = &clk->pll;
+	clk->ex_dly.init = &ex_dly_init;
+	ret = devm_clk_hw_register(dev, &clk->ex_dly);
+	if (ret)
+		dev_err_probe(dev, ret, "could not register %s\n",
+			      ex_dly_init.name);
+
+	hw_data->hws[LYNX10G_PLLa(index)] = &clk->pll;
+	hw_data->hws[LYNX10G_PLLa_EX_DLY(index)] = &clk->ex_dly;
+
+out:
+	kfree(ref_name);
+	kfree(pll_init.name);
+	kfree(ex_dly_init.name);
+	return ret;
+}
+
+#define NUM_PLLS 2
+#define NUM_CLKS (NUM_PLLS * LYNX10G_CLKS_PER_PLL)
+
+int lynx_clks_init(struct device *dev, struct regmap *regmap,
+		   struct clk *plls[2], struct clk *ex_dlys[2])
+{
+	int ret, i;
+	struct clk_hw_onecell_data *hw_data;
+
+	hw_data = devm_kzalloc(dev, struct_size(hw_data, hws, NUM_CLKS),
+			       GFP_KERNEL);
+	if (!hw_data)
+		return -ENOMEM;
+	hw_data->num = NUM_CLKS;
+
+	for (i = 0; i < NUM_PLLS; i++) {
+		ret = lynx_clk_init(hw_data, dev, regmap, i);
+		if (ret)
+			return ret;
+
+		plls[i] = hw_data->hws[LYNX10G_PLLa(i)]->clk;
+		ex_dlys[i] = hw_data->hws[LYNX10G_PLLa_EX_DLY(i)]->clk;
+	}
+
+	ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, hw_data);
+	if (ret)
+		dev_err_probe(dev, ret, "could not register clock provider\n");
+
+	return ret;
+}
diff --git a/drivers/phy/freescale/phy-fsl-lynx-10g.c b/drivers/phy/freescale/phy-fsl-lynx-10g.c
new file mode 100644
index 000000000000..a4cbb636386d
--- /dev/null
+++ b/drivers/phy/freescale/phy-fsl-lynx-10g.c
@@ -0,0 +1,1162 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Sean Anderson <sean.anderson@seco.com>
+ *
+ * This driver is for the Lynx 10G phys found on many QorIQ devices, including
+ * the Layerscape series.
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+#include <linux/phy.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+
+#include "lynx-10g.h"
+
+#define TCALCR		0x90
+#define TCALCR1		0x94
+#define RCALCR		0xa0
+#define RCALCR1		0xa4
+
+#define CALCR_CALRST_B	BIT(27)
+
+#define LS_PCCR_BASE	0x200
+#define PCCR_STRIDE	0x4
+
+#define LS_PCCRa(a)	(LS_PCCR_BASE + (a) * PCCR_STRIDE)
+
+#define PCCR8_SGMIIa_KX		BIT(3)
+#define PCCR8_SGMIIa_MASK	GENMASK(3, 0)
+#define PCCR8_SGMIIa_SHIFT(a)	(28 - (a) * 4)
+
+#define PCCR9_QSGMIIa_MASK	GENMASK(2, 0)
+#define PCCR9_QSGMIIa_SHIFT(a)	(28 - (a) * 4)
+
+#define PCCRB_XFIa_MASK		GENMASK(2, 0)
+#define PCCRB_XFIa_SHIFT(a)	(28 - (a) * 4)
+
+#define LANE_BASE	0x800
+#define LANE_STRIDE	0x40
+#define LNm(m, off)	(LANE_BASE + (m) * LANE_STRIDE + (off))
+#define LNmGCR0(m)	LNm(m, 0x00)
+#define LNmGCR1(m)	LNm(m, 0x04)
+#define LNmSSCR0(m)	LNm(m, 0x0C)
+#define LNmRECR0(m)	LNm(m, 0x10)
+#define LNmRECR1(m)	LNm(m, 0x14)
+#define LNmTECR0(m)	LNm(m, 0x18)
+#define LNmSSCR1(m)	LNm(m, 0x1C)
+#define LNmTTLCR0(m)	LNm(m, 0x20)
+
+#define LNmGCR0_RPLL_LES	BIT(31)
+#define LNmGCR0_RRAT_SEL	GENMASK(29, 28)
+#define LNmGCR0_TPLL_LES	BIT(27)
+#define LNmGCR0_TRAT_SEL	GENMASK(25, 24)
+#define LNmGCR0_RRST_B		BIT(22)
+#define LNmGCR0_TRST_B		BIT(21)
+#define LNmGCR0_RX_PD		BIT(20)
+#define LNmGCR0_TX_PD		BIT(19)
+#define LNmGCR0_IF20BIT_EN	BIT(18)
+#define LNmGCR0_FIRST_LANE	BIT(16)
+#define LNmGCR0_TTRM_VM_SEL	GENMASK(13, 12)
+#define LNmGCR0_PROTS		GENMASK(11, 7)
+
+#define LNmGCR0_RAT_SEL_SAME		0b00
+#define LNmGCR0_RAT_SEL_HALF		0b01
+#define LNmGCR0_RAT_SEL_QUARTER		0b10
+#define LNmGCR0_RAT_SEL_DOUBLE		0b11
+
+#define LNmGCR0_PROTS_PCIE		0b00000
+#define LNmGCR0_PROTS_SGMII		0b00001
+#define LNmGCR0_PROTS_SATA		0b00010
+#define LNmGCR0_PROTS_XFI		0b01010
+
+#define LNmGCR1_RDAT_INV	BIT(31)
+#define LNmGCR1_TDAT_INV	BIT(30)
+#define LNmGCR1_OPAD_CTL	BIT(26)
+#define LNmGCR1_REIDL_TH	GENMASK(22, 20)
+#define LNmGCR1_REIDL_EX_SEL	GENMASK(19, 18)
+#define LNmGCR1_REIDL_ET_SEL	GENMASK(17, 16)
+#define LNmGCR1_REIDL_EX_MSB	BIT(15)
+#define LNmGCR1_REIDL_ET_MSB	BIT(14)
+#define LNmGCR1_REQ_CTL_SNP	BIT(13)
+#define LNmGCR1_REQ_CDR_SNP	BIT(12)
+#define LNmGCR1_TRSTDIR		BIT(7)
+#define LNmGCR1_REQ_BIN_SNP	BIT(6)
+#define LNmGCR1_ISLEW_RCTL	GENMASK(5, 4)
+#define LNmGCR1_OSLEW_RCTL	GENMASK(1, 0)
+
+#define LNmRECR0_RXEQ_BST	BIT(28)
+#define LNmRECR0_GK2OVD		GENMASK(27, 24)
+#define LNmRECR0_GK3OVD		GENMASK(19, 16)
+#define LNmRECR0_GK2OVD_EN	BIT(15)
+#define LNmRECR0_GK3OVD_EN	BIT(14)
+#define LNmRECR0_OSETOVD_EN	BIT(13)
+#define LNmRECR0_BASE_WAND	GENMASK(11, 10)
+#define LNmRECR0_OSETOVD	GENMASK(6, 0)
+
+#define LNmRECR0_BASE_WAND_OFF		0b00
+#define LNmRECR0_BASE_WAND_DEFAULT	0b01
+#define LNmRECR0_BASE_WAND_ALTERNATE	0b10
+#define LNmRECR0_BASE_WAND_OSETOVD	0b11
+
+#define LNmTECR0_TEQ_TYPE	GENMASK(29, 28)
+#define LNmTECR0_SGN_PREQ	BIT(26)
+#define LNmTECR0_RATIO_PREQ	GENMASK(25, 22)
+#define LNmTECR0_SGN_POST1Q	BIT(21)
+#define LNmTECR0_RATIO_PST1Q	GENMASK(20, 16)
+#define LNmTECR0_ADPT_EQ	GENMASK(13, 8)
+#define LNmTECR0_AMP_RED	GENMASK(5, 0)
+
+#define LNmTECR0_TEQ_TYPE_NONE		0b00
+#define LNmTECR0_TEQ_TYPE_POST		0b01
+#define LNmTECR0_TEQ_TYPE_BOTH		0b10
+
+#define LNmTTLCR0_FLT_SEL	GENMASK(29, 24)
+
+#define LS_SGMII_BASE	0x1800
+#define LS_QSGMII_BASE	0x1880
+#define LS_XFI_BASE	0x1980
+
+#define PCS_STRIDE	0x10
+#define CR_STRIDE	0x4
+#define PCSa(a, base, cr)	(base + (a) * PCS_STRIDE + (cr) * CR_STRIDE)
+
+/* https://community.nxp.com/t5/Layerscape/LS1043A-SERDES-PLL-reset-causes-PHY-link-fail/m-p/1375359#M9456 */
+#define PCSaCR0_RST_B		BIT(30)
+#define PCSaCR1_MDEV_PORT	GENMASK(31, 27)
+
+#define LS_SGMIIaCR1(a)		PCSa(a, LS_SGMII_BASE, 1)
+#define SGMIIaCR1_SGPCS_EN	BIT(11)
+
+enum lynx_protocol {
+	LYNX_PROTO_NONE = 0,
+	LYNX_PROTO_SGMII,
+	LYNX_PROTO_SGMII25, /* Not tested */
+	LYNX_PROTO_1000BASEKX, /* Not tested */
+	LYNX_PROTO_QSGMII, /* Not tested */
+	LYNX_PROTO_XFI,
+	LYNX_PROTO_10GKR, /* Link training unimplemented */
+	LYNX_PROTO_LAST,
+};
+
+static const char lynx_proto_str[][16] = {
+	[LYNX_PROTO_NONE] = "unknown",
+	[LYNX_PROTO_SGMII] = "SGMII",
+	[LYNX_PROTO_SGMII25] = "2.5G SGMII",
+	[LYNX_PROTO_1000BASEKX] = "1000BASE-KX",
+	[LYNX_PROTO_QSGMII] = "QSGMII",
+	[LYNX_PROTO_XFI] = "XFI",
+	[LYNX_PROTO_10GKR] = "10GBASE-KR",
+};
+
+#define PROTO_MASK(proto) BIT(LYNX_PROTO_##proto)
+
+/**
+ * struct lynx_proto_params - Parameters for configuring a protocol
+ * @frate_khz: The PLL rate, in kHz
+ * @rat_sel: The divider to get the line rate
+ * @if20bit: Whether the proto is 20 bits or 10 bits
+ * @prots: Lane protocol select
+ * @reidl_th: Receiver electrical idle detection threshold
+ * @reidl_ex: Exit electrical idle filter
+ * @reidl_et: Enter idle filter
+ * @slew: Slew control
+ * @baseline_wander: Enable baseline wander correction
+ * @gain: Adaptive equalization gain override
+ * @offset_override: Adaptive equalization offset override
+ * @preq_ratio: Ratio of full swing transition bit to pre-cursor
+ * @postq_ratio: Ratio of full swing transition bit to first post-cursor.
+ * @adpt_eq: Transmitter Adjustments for 8G/10G
+ * @amp_red: Overall TX Amplitude Reduction
+ * @flt_sel: TTL configuration selector
+ */
+struct lynx_proto_params {
+	u32 frate_khz;
+	u8 rat_sel;
+	u8 prots;
+	u8 reidl_th;
+	u8 reidl_ex;
+	u8 reidl_et;
+	u8 slew;
+	u8 gain;
+	u8 baseline_wander;
+	u8 offset_override;
+	u8 preq_ratio;
+	u8 postq_ratio;
+	u8 adpt_eq;
+	u8 amp_red;
+	u8 flt_sel;
+	bool if20bit;
+};
+
+static const struct lynx_proto_params lynx_proto_params[] = {
+	[LYNX_PROTO_SGMII] = {
+		.frate_khz = 5000000,
+		.rat_sel = LNmGCR0_RAT_SEL_QUARTER,
+		.if20bit = false,
+		.prots = LNmGCR0_PROTS_SGMII,
+		.reidl_th = 0b001,
+		.reidl_ex = 0b011,
+		.reidl_et = 0b100,
+		.slew = 0b01,
+		.gain = 0b1111,
+		.offset_override = 0b0011111,
+		.adpt_eq = 0b110000,
+		.amp_red = 0b000110,
+		.flt_sel = 0b111001,
+	},
+	[LYNX_PROTO_1000BASEKX] = {
+		.frate_khz = 5000000,
+		.rat_sel = LNmGCR0_RAT_SEL_QUARTER,
+		.if20bit = false,
+		.prots = LNmGCR0_PROTS_SGMII,
+		.slew = 0b01,
+		.gain = 0b1111,
+		.offset_override = 0b0011111,
+		.adpt_eq = 0b110000,
+		.flt_sel = 0b111001,
+	},
+	[LYNX_PROTO_SGMII25] = {
+		.frate_khz = 3125000,
+		.rat_sel = LNmGCR0_RAT_SEL_SAME,
+		.if20bit = false,
+		.prots = LNmGCR0_PROTS_SGMII,
+		.slew = 0b10,
+		.offset_override = 0b0011111,
+		.postq_ratio = 0b00110,
+		.adpt_eq = 0b110000,
+	},
+	[LYNX_PROTO_QSGMII] = {
+		.frate_khz = 5000000,
+		.rat_sel = LNmGCR0_RAT_SEL_SAME,
+		.if20bit = true,
+		.prots = LNmGCR0_PROTS_SGMII,
+		.slew = 0b01,
+		.offset_override = 0b0011111,
+		.postq_ratio = 0b00110,
+		.adpt_eq = 0b110000,
+		.amp_red = 0b000010,
+	},
+	[LYNX_PROTO_XFI] = {
+		.frate_khz = 5156250,
+		.rat_sel = LNmGCR0_RAT_SEL_DOUBLE,
+		.if20bit = true,
+		.prots = LNmGCR0_PROTS_XFI,
+		.slew = 0b01,
+		.baseline_wander = LNmRECR0_BASE_WAND_DEFAULT,
+		.offset_override = 0b1011111,
+		.postq_ratio = 0b00011,
+		.adpt_eq = 0b110000,
+		.amp_red = 0b000111,
+	},
+	[LYNX_PROTO_10GKR] = {
+		.frate_khz = 5156250,
+		.rat_sel = LNmGCR0_RAT_SEL_DOUBLE,
+		.if20bit = true,
+		.prots = LNmGCR0_PROTS_XFI,
+		.slew = 0b01,
+		.baseline_wander = LNmRECR0_BASE_WAND_DEFAULT,
+		.offset_override = 0b1011111,
+		.preq_ratio = 0b0011,
+		.postq_ratio = 0b01100,
+		.adpt_eq = 0b110000,
+	},
+};
+
+/**
+ * struct lynx_mode - A single configuration of a protocol controller
+ * @protos: A bitmask of the &enum lynx_protocol this mode supports
+ * @pccr: The number of the PCCR which contains this mode
+ * @idx: The index of the protocol controller. For example, SGMIIB would have
+ *       index 1.
+ * @cfg: The value to program into the controller to select this mode
+ *
+ * The serdes has multiple protocol controllers which can be each be selected
+ * independently. Depending on their configuration, they may use multiple lanes
+ * at once (e.g. AUI or PCIe x4). Additionally, multiple protocols may be
+ * supported by a single mode (XFI and 10GKR differ only in their protocol
+ * parameters).
+ */
+struct lynx_mode {
+	u16 protos;
+	u8 pccr;
+	u8 idx;
+	u8 cfg;
+};
+
+static_assert(LYNX_PROTO_LAST - 1 <=
+	      sizeof_field(struct lynx_mode, protos) * BITS_PER_BYTE);
+
+struct lynx_priv;
+
+/**
+ * struct lynx_cfg - Configuration for a particular serdes
+ * @lanes: Number of lanes
+ * @endian: Endianness of the registers
+ * @mode_conflict: Determine whether a protocol controller is already in use
+ *                 (by another group).
+ * @mode_apply: Apply a given protocol. This includes programming the
+ *              appropriate config into the PCCR, as well as enabling/disabling
+ *              any other registers (such as the enabling MDIO access).
+ *              %LYNX_PROTO_NONE may be used to clear any associated registers.
+ * @mode_init: Finish initializing a mode. All fields are filled in except for
+ *             protos. Type is one of PHY_TYPE_*. mode->protos should be filled
+ *             in, and the other fields should be sanity-checked.
+ */
+struct lynx_cfg {
+	unsigned int lanes;
+	enum regmap_endian endian;
+	bool (*mode_conflict)(struct lynx_priv *serdes,
+			      const struct lynx_mode *mode);
+	void (*mode_apply)(struct lynx_priv *serdes,
+			   const struct lynx_mode *mode,
+			   enum lynx_protocol proto);
+	int (*mode_init)(struct lynx_priv *serdes, struct lynx_mode *mode,
+			 int type);
+};
+
+/**
+ * struct lynx_priv - Driver data for the serdes
+ * @lock: A lock protecting "common" registers in @regmap, as well as the
+ *        members of this struct. Lane-specific registers are protected by the
+ *        phy's lock. PLL registers are protected by the clock's lock.
+ * @dev: The serdes device
+ * @regmap: The backing regmap
+ * @cfg: SoC-specific configuration
+ * @plls: The PLLs
+ * @ex_dlys: The "ex_dly" clocks
+ * @used_lanes: Bitmap of the lanes currently used by phys
+ */
+struct lynx_priv {
+	struct mutex lock;
+	struct device *dev;
+	struct regmap *regmap;
+	const struct lynx_cfg *cfg;
+	struct clk *plls[2], *ex_dlys[2];
+	unsigned int used_lanes;
+};
+
+/**
+ * struct lynx_group - Driver data for a group of lanes
+ * @serdes: The parent serdes
+ * @pll: The currently-used pll
+ * @ex_dly: The ex_dly clock, if used
+ * @modes: Valid protocol controller configurations
+ * @mode_count: Number of modes in @modes
+ * @first_lane: The first lane in the group
+ * @last_lane: The last lane in the group
+ * @proto: The currently-configured protocol
+ */
+struct lynx_group {
+	struct lynx_priv *serdes;
+	struct clk *pll, *ex_dly;
+	const struct lynx_mode *modes;
+	size_t mode_count;
+	unsigned int first_lane;
+	unsigned int last_lane;
+	enum lynx_protocol proto;
+};
+
+static u32 lynx_read(struct lynx_priv *serdes, u32 reg)
+{
+	unsigned int ret = 0;
+
+	WARN_ON_ONCE(regmap_read(serdes->regmap, reg, &ret));
+	dev_vdbg(serdes->dev, "%.8x <= %.8x\n", ret, reg);
+	return ret;
+}
+
+static void lynx_write(struct lynx_priv *serdes, u32 val, u32 reg)
+{
+	dev_vdbg(serdes->dev, "%.8x => %.8x\n", val, reg);
+	WARN_ON_ONCE(regmap_write(serdes->regmap, reg, val));
+}
+
+/**
+ * lynx_lane_bitmap() - Get a bitmap for a group of lanes
+ * @group: The group of lanes
+ *
+ * Return: A mask containing all bits between @group->first and @group->last
+ */
+static unsigned int lynx_lane_bitmap(struct lynx_group *group)
+{
+	if (group->first_lane > group->last_lane)
+		return GENMASK(group->first_lane, group->last_lane);
+	else
+		return GENMASK(group->last_lane, group->first_lane);
+}
+
+static int lynx_init(struct phy *phy)
+{
+	int ret = 0;
+	struct lynx_group *group = phy_get_drvdata(phy);
+	struct lynx_priv *serdes = group->serdes;
+	unsigned int lane_mask = lynx_lane_bitmap(group);
+
+	mutex_lock(&serdes->lock);
+	if (serdes->used_lanes & lane_mask)
+		ret = -EBUSY;
+	else
+		serdes->used_lanes |= lane_mask;
+	mutex_unlock(&serdes->lock);
+	return ret;
+}
+
+static int lynx_exit(struct phy *phy)
+{
+	struct lynx_group *group = phy_get_drvdata(phy);
+	struct lynx_priv *serdes = group->serdes;
+
+	clk_disable_unprepare(group->ex_dly);
+	group->ex_dly = NULL;
+
+	clk_disable_unprepare(group->pll);
+	clk_rate_exclusive_put(group->pll);
+	group->pll = NULL;
+
+	mutex_lock(&serdes->lock);
+	serdes->used_lanes &= ~lynx_lane_bitmap(group);
+	mutex_unlock(&serdes->lock);
+	return 0;
+}
+
+/*
+ * This is tricky. If first_lane=1 and last_lane=0, the condition will see 2,
+ * 1, 0. But the loop body will see 1, 0. We do this to avoid underflow. We
+ * can't pull the same trick when incrementing, because then we might have to
+ * start at -1 if (e.g.) first_lane = 0.
+ */
+#define for_range(val, start, end) \
+	for (val = start < end ? start : start + 1; \
+	     start < end ? val <= end : val-- > end; \
+	     start < end ? val++ : 0)
+#define for_each_lane(lane, group) \
+	for_range(lane, group->first_lane, group->last_lane)
+#define for_each_lane_reverse(lane, group) \
+	for_range(lane, group->last_lane, group->first_lane)
+
+static int lynx_power_on(struct phy *phy)
+{
+	int i;
+	struct lynx_group *group = phy_get_drvdata(phy);
+	u32 gcr0;
+
+	for_each_lane(i, group) {
+		gcr0 = lynx_read(group->serdes, LNmGCR0(i));
+		gcr0 &= ~(LNmGCR0_RX_PD | LNmGCR0_TX_PD);
+		lynx_write(group->serdes, gcr0, LNmGCR0(i));
+
+		usleep_range(15, 30);
+		gcr0 |= LNmGCR0_RRST_B | LNmGCR0_TRST_B;
+		lynx_write(group->serdes, gcr0, LNmGCR0(i));
+	}
+
+	return 0;
+}
+
+static void lynx_power_off_group(struct lynx_group *group)
+{
+	int i;
+
+	for_each_lane_reverse(i, group) {
+		u32 gcr0 = lynx_read(group->serdes, LNmGCR0(i));
+
+		gcr0 |= LNmGCR0_RX_PD | LNmGCR0_TX_PD;
+		gcr0 &= ~(LNmGCR0_RRST_B | LNmGCR0_TRST_B);
+		lynx_write(group->serdes, gcr0, LNmGCR0(i));
+	}
+}
+
+static int lynx_power_off(struct phy *phy)
+{
+	lynx_power_off_group(phy_get_drvdata(phy));
+	return 0;
+}
+
+/**
+ * lynx_lookup_proto() - Convert a phy-subsystem mode to a protocol
+ * @mode: The mode to convert
+ * @submode: The submode of @mode
+ *
+ * Return: A corresponding serdes-specific mode
+ */
+static enum lynx_protocol lynx_lookup_proto(enum phy_mode mode, int submode)
+{
+	switch (mode) {
+	case PHY_MODE_ETHERNET:
+		switch (submode) {
+		case PHY_INTERFACE_MODE_SGMII:
+		case PHY_INTERFACE_MODE_1000BASEX:
+			return LYNX_PROTO_SGMII;
+		/* TODO: 1000Base-KX */
+		case PHY_INTERFACE_MODE_2500BASEX:
+			return LYNX_PROTO_SGMII25;
+		case PHY_INTERFACE_MODE_QSGMII:
+			return LYNX_PROTO_QSGMII;
+		case PHY_INTERFACE_MODE_XGMII:
+		case PHY_INTERFACE_MODE_10GBASER:
+			return LYNX_PROTO_XFI;
+		case PHY_INTERFACE_MODE_10GKR:
+			return LYNX_PROTO_10GKR;
+		default:
+			return LYNX_PROTO_NONE;
+		}
+	default:
+		return LYNX_PROTO_NONE;
+	}
+}
+
+/**
+ * lynx_lookup_mode() - Get the mode for a group/protocol combination
+ * @group: The group of lanes to use
+ * @proto: The protocol to use
+ *
+ * Return: An appropriate mode to use, or %NULL if none match.
+ */
+static const struct lynx_mode *lynx_lookup_mode(struct lynx_group *group,
+						enum lynx_protocol proto)
+{
+	int i;
+
+	for (i = 0; i < group->mode_count; i++) {
+		const struct lynx_mode *mode = &group->modes[i];
+
+		if (BIT(proto) & mode->protos)
+			return mode;
+	}
+
+	return NULL;
+}
+
+static int lynx_validate(struct phy *phy, enum phy_mode phy_mode, int submode,
+			 union phy_configure_opts *opts)
+{
+	enum lynx_protocol proto;
+	struct lynx_group *group = phy_get_drvdata(phy);
+	const struct lynx_mode *mode;
+
+	proto = lynx_lookup_proto(phy_mode, submode);
+	if (proto == LYNX_PROTO_NONE)
+		return -EINVAL;
+
+	/* Nothing to do */
+	if (proto == group->proto)
+		return 0;
+
+	mode = lynx_lookup_mode(group, proto);
+	if (!mode)
+		return -EINVAL;
+
+	return 0;
+}
+
+#define abs_diff(a, b) ({ \
+	typeof(a) _a = (a); \
+	typeof(b) _b = (b); \
+	_a > _b ? _a - _b : _b - _a; \
+})
+
+static int lynx_set_mode(struct phy *phy, enum phy_mode phy_mode, int submode)
+{
+	enum lynx_protocol proto;
+	const struct lynx_proto_params *params;
+	const struct lynx_mode *old_mode = NULL, *new_mode;
+	int i, pll, ret;
+	struct lynx_group *group = phy_get_drvdata(phy);
+	struct lynx_priv *serdes = group->serdes;
+	u32 tmp, teq;
+	u32 gcr0 = 0, gcr1 = 0, recr0 = 0, tecr0 = 0;
+	u32 gcr0_mask = 0, gcr1_mask = 0, recr0_mask = 0, tecr0_mask = 0;
+
+	proto = lynx_lookup_proto(phy_mode, submode);
+	if (proto == LYNX_PROTO_NONE) {
+		dev_dbg(&phy->dev, "unknown mode/submode %d/%d\n",
+			phy_mode, submode);
+		return -EINVAL;
+	}
+
+	/* Nothing to do */
+	if (proto == group->proto)
+		return 0;
+
+	new_mode = lynx_lookup_mode(group, proto);
+	if (!new_mode) {
+		dev_dbg(&phy->dev, "could not find mode for %s on lanes %u to %u\n",
+			lynx_proto_str[proto], group->first_lane,
+			group->last_lane);
+		return -EINVAL;
+	}
+
+	if (group->proto != LYNX_PROTO_NONE) {
+		old_mode = lynx_lookup_mode(group, group->proto);
+		if (!old_mode) {
+			dev_err(&phy->dev, "could not find mode for %s\n",
+				lynx_proto_str[group->proto]);
+			return -EBUSY;
+		}
+	}
+
+	mutex_lock(&serdes->lock);
+	if (serdes->cfg->mode_conflict(serdes, new_mode)) {
+		dev_dbg(&phy->dev, "%s%c already in use\n",
+			lynx_proto_str[__ffs(new_mode->protos)],
+			'A' + new_mode->idx);
+		ret = -EBUSY;
+		goto out;
+	}
+
+	clk_disable_unprepare(group->ex_dly);
+	group->ex_dly = NULL;
+
+	clk_disable_unprepare(group->pll);
+	clk_rate_exclusive_put(group->pll);
+	group->pll = NULL;
+
+	/* First, try to use a PLL which already has the correct rate */
+	params = &lynx_proto_params[proto];
+	for (pll = 0; pll < ARRAY_SIZE(serdes->plls); pll++) {
+		struct clk *clk = serdes->plls[pll];
+		unsigned long rate = clk_get_rate(clk);
+		unsigned long error = abs_diff(rate, params->frate_khz);
+
+		dev_dbg(&phy->dev, "pll%d has rate %lu (error=%lu)\n", pll,
+			rate, error);
+		/* Accept up to 100ppm deviation */
+		if (error && params->frate_khz / error < 10000)
+			continue;
+
+		if (!clk_set_rate_exclusive(clk, rate))
+			goto got_pll;
+		/*
+		 * Someone else got a different rate first (or there was some
+		 * other error)
+		 */
+	}
+
+	/* If neither PLL has the right rate, try setting it */
+	for (pll = 0; pll < 2; pll++) {
+		ret = clk_set_rate_exclusive(serdes->plls[pll],
+					     params->frate_khz);
+		if (!ret)
+			goto got_pll;
+	}
+
+	dev_dbg(&phy->dev, "could not get a pll at %ukHz\n",
+		params->frate_khz);
+	goto out;
+
+got_pll:
+	group->pll = serdes->plls[pll];
+	ret = clk_prepare_enable(group->pll);
+	if (ret)
+		goto out;
+
+	gcr0_mask |= LNmGCR0_RRAT_SEL | LNmGCR0_TRAT_SEL;
+	gcr0_mask |= LNmGCR0_RPLL_LES | LNmGCR0_TPLL_LES;
+	gcr0_mask |= LNmGCR0_RRST_B | LNmGCR0_TRST_B;
+	gcr0_mask |= LNmGCR0_RX_PD | LNmGCR0_TX_PD;
+	gcr0_mask |= LNmGCR0_IF20BIT_EN | LNmGCR0_PROTS;
+	gcr0 |= FIELD_PREP(LNmGCR0_RPLL_LES, !pll);
+	gcr0 |= FIELD_PREP(LNmGCR0_TPLL_LES, !pll);
+	gcr0 |= FIELD_PREP(LNmGCR0_RRAT_SEL, params->rat_sel);
+	gcr0 |= FIELD_PREP(LNmGCR0_TRAT_SEL, params->rat_sel);
+	gcr0 |= FIELD_PREP(LNmGCR0_IF20BIT_EN, params->if20bit);
+	gcr0 |= FIELD_PREP(LNmGCR0_PROTS, params->prots);
+
+	gcr1_mask |= LNmGCR1_RDAT_INV | LNmGCR1_TDAT_INV;
+	gcr1_mask |= LNmGCR1_OPAD_CTL | LNmGCR1_REIDL_TH;
+	gcr1_mask |= LNmGCR1_REIDL_EX_SEL | LNmGCR1_REIDL_ET_SEL;
+	gcr1_mask |= LNmGCR1_REIDL_EX_MSB | LNmGCR1_REIDL_ET_MSB;
+	gcr1_mask |= LNmGCR1_REQ_CTL_SNP | LNmGCR1_REQ_CDR_SNP;
+	gcr1_mask |= LNmGCR1_TRSTDIR | LNmGCR1_REQ_BIN_SNP;
+	gcr1_mask |= LNmGCR1_ISLEW_RCTL | LNmGCR1_OSLEW_RCTL;
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_TH, params->reidl_th);
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_EX_SEL, params->reidl_ex & 3);
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_ET_SEL, params->reidl_et & 3);
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_EX_MSB, params->reidl_ex >> 2);
+	gcr1 |= FIELD_PREP(LNmGCR1_REIDL_ET_MSB, params->reidl_et >> 2);
+	gcr1 |= FIELD_PREP(LNmGCR1_TRSTDIR,
+			   group->first_lane > group->last_lane);
+	gcr1 |= FIELD_PREP(LNmGCR1_ISLEW_RCTL, params->slew);
+	gcr1 |= FIELD_PREP(LNmGCR1_OSLEW_RCTL, params->slew);
+
+	recr0_mask |= LNmRECR0_RXEQ_BST | LNmRECR0_BASE_WAND;
+	recr0_mask |= LNmRECR0_GK2OVD | LNmRECR0_GK3OVD;
+	recr0_mask |= LNmRECR0_GK2OVD_EN | LNmRECR0_GK3OVD_EN;
+	recr0_mask |= LNmRECR0_OSETOVD_EN | LNmRECR0_OSETOVD;
+	if (params->gain) {
+		recr0 |= FIELD_PREP(LNmRECR0_GK2OVD, params->gain);
+		recr0 |= FIELD_PREP(LNmRECR0_GK3OVD, params->gain);
+		recr0 |= LNmRECR0_GK2OVD_EN | LNmRECR0_GK3OVD_EN;
+	}
+	recr0 |= FIELD_PREP(LNmRECR0_BASE_WAND, params->baseline_wander);
+	recr0 |= FIELD_PREP(LNmRECR0_OSETOVD, params->offset_override);
+
+	tecr0_mask |= LNmTECR0_TEQ_TYPE;
+	tecr0_mask |= LNmTECR0_SGN_PREQ | LNmTECR0_RATIO_PREQ;
+	tecr0_mask |= LNmTECR0_SGN_POST1Q | LNmTECR0_RATIO_PST1Q;
+	tecr0_mask |= LNmTECR0_ADPT_EQ | LNmTECR0_AMP_RED;
+	teq = LNmTECR0_TEQ_TYPE_NONE;
+	if (params->postq_ratio) {
+		teq = LNmTECR0_TEQ_TYPE_POST;
+		tecr0 |= FIELD_PREP(LNmTECR0_SGN_POST1Q, 1);
+		tecr0 |= FIELD_PREP(LNmTECR0_RATIO_PST1Q, params->postq_ratio);
+	}
+	if (params->preq_ratio) {
+		teq = LNmTECR0_TEQ_TYPE_BOTH;
+		tecr0 |= FIELD_PREP(LNmTECR0_SGN_PREQ, 1);
+		tecr0 |= FIELD_PREP(LNmTECR0_RATIO_PREQ, params->preq_ratio);
+	}
+	tecr0 |= FIELD_PREP(LNmTECR0_TEQ_TYPE, teq);
+	tecr0 |= FIELD_PREP(LNmTECR0_ADPT_EQ, params->adpt_eq);
+	tecr0 |= FIELD_PREP(LNmTECR0_AMP_RED, params->amp_red);
+
+	for_each_lane(i, group) {
+		tmp = lynx_read(serdes, LNmGCR0(i));
+		tmp &= ~(LNmGCR0_RRST_B | LNmGCR0_TRST_B);
+		lynx_write(serdes, tmp, LNmGCR0(i));
+	}
+
+	ndelay(50);
+
+	/* Disable the old controller */
+	if (old_mode)
+		serdes->cfg->mode_apply(serdes, old_mode, LYNX_PROTO_NONE);
+
+	for_each_lane(i, group) {
+		tmp = lynx_read(serdes, LNmGCR0(i));
+		tmp &= ~gcr0_mask;
+		tmp |= gcr0;
+		tmp |= FIELD_PREP(LNmGCR0_FIRST_LANE, i == group->first_lane);
+		lynx_write(serdes, tmp, LNmGCR0(i));
+
+		tmp = lynx_read(serdes, LNmGCR1(i));
+		tmp &= ~gcr1_mask;
+		tmp |= gcr1;
+		lynx_write(serdes, tmp, LNmGCR1(i));
+
+		tmp = lynx_read(serdes, LNmRECR0(i));
+		tmp &= ~recr0_mask;
+		tmp |= recr0;
+		lynx_write(serdes, tmp, LNmRECR0(i));
+
+		tmp = lynx_read(serdes, LNmTECR0(i));
+		tmp &= ~tecr0_mask;
+		tmp |= tecr0;
+		lynx_write(serdes, tmp, LNmTECR0(i));
+
+		tmp = lynx_read(serdes, LNmTTLCR0(i));
+		tmp &= ~LNmTTLCR0_FLT_SEL;
+		tmp |= FIELD_PREP(LNmTTLCR0_FLT_SEL, params->flt_sel);
+		lynx_write(serdes, tmp, LNmTTLCR0(i));
+	}
+
+	ndelay(120);
+
+	for_each_lane_reverse(i, group) {
+		tmp = lynx_read(serdes, LNmGCR0(i));
+		tmp |= LNmGCR0_RRST_B | LNmGCR0_TRST_B;
+		lynx_write(serdes, tmp, LNmGCR0(i));
+	}
+
+	/* Enable the new controller */
+	serdes->cfg->mode_apply(serdes, new_mode, proto);
+	if (proto == LYNX_PROTO_1000BASEKX) {
+		group->ex_dly = serdes->ex_dlys[pll];
+		/* This should never fail since it's from our internal driver */
+		WARN_ON_ONCE(clk_prepare_enable(group->ex_dly));
+	}
+	group->proto = proto;
+
+	dev_dbg(&phy->dev, "set mode to %s on lanes %u to %u\n",
+		lynx_proto_str[proto], group->first_lane, group->last_lane);
+
+out:
+	mutex_unlock(&serdes->lock);
+	return ret;
+}
+
+static const struct phy_ops lynx_phy_ops = {
+	.init = lynx_init,
+	.exit = lynx_exit,
+	.power_on = lynx_power_on,
+	.power_off = lynx_power_off,
+	.set_mode = lynx_set_mode,
+	.validate = lynx_validate,
+	.owner = THIS_MODULE,
+};
+
+static int lynx_read_u32(struct device *dev, struct fwnode_handle *fwnode,
+			 const char *prop, u32 *val)
+{
+	int ret;
+
+	ret = fwnode_property_read_u32(fwnode, prop, val);
+	if (ret)
+		dev_err(dev, "could not read %s from %pfwP: %d\n", prop,
+			fwnode, ret);
+	return ret;
+}
+
+static int lynx_probe_group(struct lynx_priv *serdes,
+			    struct fwnode_handle *fwnode)
+{
+	int i, lane_count, ret;
+	struct device *dev = serdes->dev;
+	struct fwnode_handle *mode_node;
+	struct lynx_group *group;
+	struct lynx_mode *modes;
+	struct phy *phy;
+	u32 *lanes = NULL;
+
+	group = devm_kzalloc(dev, sizeof(*group), GFP_KERNEL);
+	if (!group)
+		return -ENOMEM;
+	group->serdes = serdes;
+
+	lane_count = fwnode_property_count_u32(fwnode, "reg");
+	if (lane_count < 0) {
+		dev_err(dev, "could not read %s from %pfwP: %d\n",
+			"reg", fwnode, ret);
+		return lane_count;
+	}
+
+	lanes = kcalloc(lane_count, sizeof(*lanes), GFP_KERNEL);
+	if (!lanes)
+		return -ENOMEM;
+
+	ret = fwnode_property_read_u32_array(fwnode, "reg", lanes, lane_count);
+	if (ret) {
+		dev_err(dev, "could not read %s from %pfwP: %d\n",
+			"reg", fwnode, ret);
+		goto out;
+	}
+
+	group->first_lane = lanes[0];
+	group->last_lane = lanes[lane_count - 1];
+	for (i = 0; i < lane_count; i++) {
+		if (lanes[i] > serdes->cfg->lanes) {
+			ret = -EINVAL;
+			dev_err(dev, "lane %d not in range 0 to %u\n",
+				i, serdes->cfg->lanes);
+			goto out;
+		}
+
+		if (lanes[i] != group->first_lane +
+				i * !!(group->last_lane - group->first_lane)) {
+			ret = -EINVAL;
+			dev_err(dev, "lane %d is not monotonic\n", i);
+			goto out;
+		}
+	}
+
+	fwnode_for_each_child_node(fwnode, mode_node)
+		group->mode_count++;
+
+	modes = devm_kcalloc(dev, group->mode_count, sizeof(*group->modes),
+			     GFP_KERNEL);
+	if (!modes) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	i = 0;
+	fwnode_for_each_child_node(fwnode, mode_node) {
+		struct lynx_mode *mode = &modes[i++];
+		u32 val;
+
+		ret = lynx_read_u32(dev, mode_node, "fsl,pccr", &val);
+		if (ret)
+			goto out;
+		mode->pccr = val;
+
+		ret = lynx_read_u32(dev, mode_node, "fsl,index", &val);
+		if (ret)
+			goto out;
+		mode->idx = val;
+
+		ret = lynx_read_u32(dev, mode_node, "fsl,cfg", &val);
+		if (ret)
+			goto out;
+		mode->cfg = val;
+
+		ret = lynx_read_u32(dev, mode_node, "fsl,type", &val);
+		if (ret)
+			goto out;
+
+		ret = serdes->cfg->mode_init(serdes, mode, val);
+		if (ret)
+			goto out;
+
+		dev_dbg(dev, "mode PCCR%X.%s%c_CFG=%x on lanes %u to %u\n",
+			mode->pccr, lynx_proto_str[__ffs(mode->protos)],
+			'A' + mode->idx, mode->cfg, group->first_lane,
+			group->last_lane);
+	}
+
+	WARN_ON(i != group->mode_count);
+	group->modes = modes;
+
+	/* Deselect anything configured by the RCW/bootloader */
+	for (i = 0; i < group->mode_count; i++)
+		serdes->cfg->mode_apply(serdes, &group->modes[i],
+					LYNX_PROTO_NONE);
+
+	/* Disable the lanes for now */
+	lynx_power_off_group(group);
+
+	phy = devm_phy_create(dev, to_of_node(fwnode), &lynx_phy_ops);
+	ret = PTR_ERR_OR_ZERO(phy);
+	if (ret)
+		dev_err_probe(dev, ret, "could not create phy\n");
+	else
+		phy_set_drvdata(phy, group);
+
+out:
+	kfree(lanes);
+	return ret;
+}
+
+static int lynx_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct device *dev = &pdev->dev;
+	struct fwnode_handle *group_node;
+	struct lynx_priv *serdes;
+	struct phy_provider *provider;
+	struct regmap_config regmap_config = {
+		.reg_bits = 32,
+		.reg_stride = 4,
+		.val_bits = 32,
+		.disable_locking = true,
+	};
+	struct resource *res;
+	void __iomem *base;
+
+	serdes = devm_kzalloc(dev, sizeof(*serdes), GFP_KERNEL);
+	if (!serdes)
+		return -ENOMEM;
+
+	serdes->dev = dev;
+	platform_set_drvdata(pdev, serdes);
+	mutex_init(&serdes->lock);
+	serdes->cfg = device_get_match_data(dev);
+
+	base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(base)) {
+		ret = PTR_ERR(base);
+		dev_err_probe(dev, ret, "could not get/map registers\n");
+		return ret;
+	}
+
+	regmap_config.val_format_endian = serdes->cfg->endian;
+	regmap_config.max_register = res->end - res->start;
+	serdes->regmap = devm_regmap_init_mmio(dev, base, &regmap_config);
+	if (IS_ERR(serdes->regmap)) {
+		ret = PTR_ERR(serdes->regmap);
+		dev_err_probe(dev, ret, "could not create regmap\n");
+		return ret;
+	}
+
+	ret = lynx_clks_init(dev, serdes->regmap, serdes->plls,
+			     serdes->ex_dlys);
+	if (ret)
+		return ret;
+
+	device_for_each_child_node(dev, group_node) {
+		ret = lynx_probe_group(serdes, group_node);
+		if (ret)
+			return ret;
+	}
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	ret = PTR_ERR_OR_ZERO(provider);
+	if (ret)
+		dev_err_probe(dev, ret, "could not register phy provider\n");
+	else
+		dev_info(dev, "probed with %d lanes\n", serdes->cfg->lanes);
+	return ret;
+}
+
+/*
+ * These are common helpers for the PCCRs found on (most) Layerscape SoCs.
+ * There is an earlier layout used on most T-series SoCs, as well as the
+ * LS1020A/21A/22A.
+ */
+
+static int lynx_ls_pccr_params(const struct lynx_mode *mode, u32 *off,
+			       u32 *shift, u32 *mask)
+{
+	if (mode->protos & PROTO_MASK(SGMII)) {
+		*off = LS_PCCRa(0x8);
+		*mask = PCCR8_SGMIIa_MASK;
+		*shift = PCCR8_SGMIIa_SHIFT(mode->idx);
+	} else if (mode->protos & PROTO_MASK(QSGMII)) {
+		*off = LS_PCCRa(0x9);
+		*mask = PCCR9_QSGMIIa_MASK;
+		*shift = PCCR9_QSGMIIa_SHIFT(mode->idx);
+	} else if (mode->protos & PROTO_MASK(XFI)) {
+		*off = LS_PCCRa(0xB);
+		*mask = PCCRB_XFIa_MASK;
+		*shift = PCCRB_XFIa_SHIFT(mode->idx);
+	} else {
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static bool lynx_ls_mode_conflict(struct lynx_priv *serdes,
+				  const struct lynx_mode *mode)
+{
+	u32 off, shift, mask;
+
+	if (WARN_ON_ONCE(lynx_ls_pccr_params(mode, &off, &shift, &mask)))
+		return true;
+
+	return (lynx_read(serdes, off) >> shift) & mask;
+}
+
+static void lynx_ls_mode_apply(struct lynx_priv *serdes,
+			       const struct lynx_mode *mode,
+			       enum lynx_protocol proto)
+{
+	u32 base, pccr, off, shift, mask;
+
+	if (WARN_ON_ONCE(proto != LYNX_PROTO_NONE &&
+			 !(mode->protos & BIT(proto))))
+		return;
+	if (WARN_ON_ONCE(lynx_ls_pccr_params(mode, &off, &shift, &mask)))
+		return;
+
+	dev_dbg(serdes->dev, "applying %s to PCCR%X.%s%c_CFG\n",
+		lynx_proto_str[proto], mode->pccr,
+		lynx_proto_str[__ffs(mode->protos)], 'A' + mode->idx);
+
+	base = 0;
+	if (mode->protos & PROTO_MASK(SGMII))
+		base = LS_SGMII_BASE;
+	else if (mode->protos & PROTO_MASK(QSGMII))
+		base = LS_QSGMII_BASE;
+	else if (mode->protos & PROTO_MASK(XFI))
+		base = LS_XFI_BASE;
+
+	if (base && proto == LYNX_PROTO_NONE) {
+		u32 cr0 = lynx_read(serdes, PCSa(mode->idx, base, 0));
+
+		cr0 |= PCSaCR0_RST_B;
+		lynx_write(serdes, cr0, PCSa(mode->idx, base, 0));
+	}
+
+	pccr = lynx_read(serdes, off);
+	pccr &= ~(mask << shift);
+	if (proto != LYNX_PROTO_NONE)
+		pccr |= mode->cfg << shift;
+
+	if (proto == LYNX_PROTO_1000BASEKX)
+		pccr |= PCCR8_SGMIIa_KX << shift;
+	lynx_write(serdes, pccr, off);
+
+	if (base && proto != LYNX_PROTO_NONE) {
+		u32 cr0 = lynx_read(serdes, PCSa(mode->idx, base, 0));
+
+		cr0 &= ~PCSaCR0_RST_B;
+		lynx_write(serdes, cr0, PCSa(mode->idx, base, 0));
+	}
+
+	if (mode->protos & PROTO_MASK(SGMII)) {
+		u32 cr1 = lynx_read(serdes, LS_SGMIIaCR1(mode->idx));
+
+		cr1 &= ~SGMIIaCR1_SGPCS_EN;
+		cr1 |= proto == LYNX_PROTO_NONE ? 0 : SGMIIaCR1_SGPCS_EN;
+		lynx_write(serdes, cr1, LS_SGMIIaCR1(mode->idx));
+	}
+}
+
+static int lynx_ls_mode_init(struct lynx_priv *serdes, struct lynx_mode *mode,
+			     int type)
+{
+	u32 max = 0, off, shift, mask;
+
+	if (mode->pccr >= 0x10) {
+		dev_err(serdes->dev, "PCCR index %u too large\n", mode->pccr);
+		return -EINVAL;
+	}
+
+	switch (type) {
+	case PHY_TYPE_2500BASEX:
+		mode->protos = PROTO_MASK(SGMII25);
+		fallthrough;
+	case PHY_TYPE_SGMII:
+		max = 8;
+		mode->protos |= PROTO_MASK(SGMII) | PROTO_MASK(1000BASEKX);
+		break;
+	case PHY_TYPE_QSGMII:
+		max = 4;
+		mode->protos = PROTO_MASK(QSGMII);
+		break;
+	case PHY_TYPE_10GBASER:
+		max = 8;
+		mode->protos = PROTO_MASK(XFI) | PROTO_MASK(10GKR);
+		break;
+	default:
+		dev_err(serdes->dev, "unknown mode type %d\n", type);
+		return -EINVAL;
+	}
+
+	if (mode->idx >= max) {
+		dev_err(serdes->dev, "%s index %u too large\n",
+			lynx_proto_str[__ffs(mode->protos)], mode->idx);
+		return -EINVAL;
+	}
+
+	if (WARN_ON_ONCE(lynx_ls_pccr_params(mode, &off, &shift, &mask)))
+		return -EINVAL;
+
+	if (!mode->cfg || mode->cfg & ~mask) {
+		dev_err(serdes->dev, "bad value %x for %s%c_CFG\n",
+			mode->cfg, lynx_proto_str[__ffs(mode->protos)],
+			'A' + mode->idx);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct lynx_cfg ls1046a_cfg = {
+	.lanes = 4,
+	.endian = REGMAP_ENDIAN_BIG,
+	.mode_conflict = lynx_ls_mode_conflict,
+	.mode_apply = lynx_ls_mode_apply,
+	.mode_init = lynx_ls_mode_init,
+};
+
+static const struct lynx_cfg ls1088a_cfg = {
+	.lanes = 4,
+	.endian = REGMAP_ENDIAN_LITTLE,
+	.mode_conflict = lynx_ls_mode_conflict,
+	.mode_apply = lynx_ls_mode_apply,
+	.mode_init = lynx_ls_mode_init,
+};
+
+static const struct of_device_id lynx_of_match[] = {
+	{ .compatible = "fsl,ls1046a-serdes", .data = &ls1046a_cfg },
+	{ .compatible = "fsl,ls1088a-serdes", .data = &ls1088a_cfg },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, lynx_of_match);
+
+static struct platform_driver lynx_driver = {
+	.probe = lynx_probe,
+	.driver = {
+		.name = "lynx_10g",
+		.of_match_table = lynx_of_match,
+	},
+};
+module_platform_driver(lynx_driver);
+
+MODULE_AUTHOR("Sean Anderson <sean.anderson@seco.com>");
+MODULE_DESCRIPTION("Lynx 10G SerDes driver");
+MODULE_LICENSE("GPL");