@@ -83,6 +83,13 @@ config ADIN_PHY
- ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
+config ADIN1100_PHY
+ tristate "Analog Devices Industrial Ethernet T1L PHYs"
+ help
+ Adds support for the Analog Devices Industrial T1L Ethernet PHYs.
+ Currently supports the:
+ - ADIN1100 - Robust,Industrial, Low Power 10BASE-T1L Ethernet PHY
+
config AQUANTIA_PHY
tristate "Aquantia PHYs"
help
@@ -31,6 +31,7 @@ sfp-obj-$(CONFIG_SFP) += sfp-bus.o
obj-y += $(sfp-obj-y) $(sfp-obj-m)
obj-$(CONFIG_ADIN_PHY) += adin.o
+obj-$(CONFIG_ADIN1100_PHY) += adin1100.o
obj-$(CONFIG_AMD_PHY) += amd.o
aquantia-objs += aquantia_main.o
ifdef CONFIG_HWMON
new file mode 100644
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Driver for Analog Devices Industrial Ethernet T1L PHYs
+ *
+ * Copyright 2020 Analog Devices Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+#include <linux/property.h>
+
+#define PHY_ID_ADIN1100 0x0283bc81
+
+#define ADIN_FORCED_MODE 0x8000
+#define ADIN_FORCED_MODE_EN BIT(0)
+
+#define ADIN_CRSM_SFT_RST 0x8810
+#define ADIN_CRSM_SFT_RST_EN BIT(0)
+
+#define ADIN_CRSM_SFT_PD_CNTRL 0x8812
+#define ADIN_CRSM_SFT_PD_CNTRL_EN BIT(0)
+
+#define ADIN_AN_PHY_INST_STATUS 0x8030
+#define ADIN_IS_CFG_SLV BIT(2)
+#define ADIN_IS_CFG_MST BIT(3)
+
+#define ADIN_CRSM_STAT 0x8818
+#define ADIN_CRSM_SFT_PD_RDY BIT(1)
+#define ADIN_CRSM_SYS_RDY BIT(0)
+
+/**
+ * struct adin_priv - ADIN PHY driver private data
+ * @tx_level_2v4_able: set if the PHY supports 2.4V TX levels (10BASE-T1L)
+ * @tx_level_2v4: set if the PHY requests 2.4V TX levels (10BASE-T1L)
+ * @tx_level_prop_present: set if the TX level is specified in DT
+ */
+struct adin_priv {
+ unsigned int tx_level_2v4_able:1;
+ unsigned int tx_level_2v4:1;
+ unsigned int tx_level_prop_present:1;
+};
+
+static int adin_read_status(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_c45_read_status(phydev);
+ if (ret)
+ return ret;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_PHY_INST_STATUS);
+ if (ret < 0)
+ return ret;
+
+ if (ret & ADIN_IS_CFG_SLV)
+ phydev->master_slave_state = MASTER_SLAVE_STATE_SLAVE;
+
+ if (ret & ADIN_IS_CFG_MST)
+ phydev->master_slave_state = MASTER_SLAVE_STATE_MASTER;
+
+ return 0;
+}
+
+static int adin_config_aneg(struct phy_device *phydev)
+{
+ struct adin_priv *priv = phydev->priv;
+ int ret;
+
+ if (phydev->autoneg == AUTONEG_DISABLE) {
+ ret = genphy_c45_pma_setup_forced(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (priv->tx_level_prop_present && priv->tx_level_2v4)
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_B10L_PMA_CTRL,
+ MDIO_PMA_10T1L_CTRL_2V4_EN);
+ else
+ ret = phy_clear_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_B10L_PMA_CTRL,
+ MDIO_PMA_10T1L_CTRL_2V4_EN);
+ if (ret < 0)
+ return ret;
+
+ /* Force PHY to use above configurations */
+ return phy_set_bits_mmd(phydev, MDIO_MMD_AN, ADIN_FORCED_MODE, ADIN_FORCED_MODE_EN);
+ }
+
+ ret = phy_clear_bits_mmd(phydev, MDIO_MMD_AN, ADIN_FORCED_MODE, ADIN_FORCED_MODE_EN);
+ if (ret < 0)
+ return ret;
+
+ /* Request increased transmit level from LP. */
+ if (priv->tx_level_prop_present && priv->tx_level_2v4) {
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_H,
+ MDIO_AN_T1_ADV_H_10L_TX_HI |
+ MDIO_AN_T1_ADV_H_10L_TX_HI_REQ);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* Disable 2.4 Vpp transmit level. */
+ if ((priv->tx_level_prop_present && !priv->tx_level_2v4) || !priv->tx_level_2v4_able) {
+ ret = phy_clear_bits_mmd(phydev, MDIO_MMD_AN, MDIO_AN_T1_ADV_H,
+ MDIO_AN_T1_ADV_H_10L_TX_HI |
+ MDIO_AN_T1_ADV_H_10L_TX_HI_REQ);
+ if (ret < 0)
+ return ret;
+ }
+
+ return genphy_c45_config_aneg(phydev);
+}
+
+static int adin_set_powerdown_mode(struct phy_device *phydev, bool en)
+{
+ int ret;
+ int val;
+
+ val = en ? ADIN_CRSM_SFT_PD_CNTRL_EN : 0;
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND1,
+ ADIN_CRSM_SFT_PD_CNTRL, val);
+ if (ret < 0)
+ return ret;
+
+ return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, ADIN_CRSM_STAT, ret,
+ (ret & ADIN_CRSM_SFT_PD_RDY) == val,
+ 1000, 30000, true);
+}
+
+static int adin_suspend(struct phy_device *phydev)
+{
+ return adin_set_powerdown_mode(phydev, true);
+}
+
+static int adin_resume(struct phy_device *phydev)
+{
+ return adin_set_powerdown_mode(phydev, false);
+}
+
+static int adin_set_loopback(struct phy_device *phydev, bool enable)
+{
+ if (enable)
+ return phy_set_bits_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_10T1L_CTRL,
+ BMCR_LOOPBACK);
+
+ /* PCS loopback (according to 10BASE-T1L spec) */
+ return phy_clear_bits_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_10T1L_CTRL,
+ BMCR_LOOPBACK);
+}
+
+static int adin_soft_reset(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ADIN_CRSM_SFT_RST, ADIN_CRSM_SFT_RST_EN);
+ if (ret < 0)
+ return ret;
+
+ return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1, ADIN_CRSM_STAT, ret,
+ (ret & ADIN_CRSM_SYS_RDY),
+ 10000, 30000, true);
+}
+
+static int adin_get_features(struct phy_device *phydev)
+{
+ struct adin_priv *priv = phydev->priv;
+ struct device *dev = &phydev->mdio.dev;
+ int ret;
+ u8 val;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_10T1L_STAT);
+ if (ret < 0)
+ return ret;
+
+ /* This depends on the voltage level from the power source */
+ priv->tx_level_2v4_able = !!(ret & MDIO_PMA_10T1L_STAT_2V4_ABLE);
+
+ phydev_dbg(phydev, "PHY supports 2.4V TX level: %s\n",
+ priv->tx_level_2v4_able ? "yes" : "no");
+
+ priv->tx_level_prop_present = device_property_present(dev, "phy-10base-t1l-2.4vpp");
+ if (priv->tx_level_prop_present) {
+ ret = device_property_read_u8(dev, "phy-10base-t1l-2.4vpp", &val);
+ if (ret < 0)
+ return ret;
+
+ priv->tx_level_2v4 = val;
+ if (!priv->tx_level_2v4 && priv->tx_level_2v4_able)
+ phydev_info(phydev,
+ "PHY supports 2.4V TX level, but disabled via config\n");
+ }
+
+ linkmode_set_bit_array(phy_basic_ports_array, ARRAY_SIZE(phy_basic_ports_array),
+ phydev->supported);
+
+ return genphy_c45_pma_read_abilities(phydev);
+}
+
+static int adin_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct adin_priv *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ phydev->priv = priv;
+
+ return 0;
+}
+
+static struct phy_driver adin_driver[] = {
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100),
+ .name = "ADIN1100",
+ .get_features = adin_get_features,
+ .soft_reset = adin_soft_reset,
+ .probe = adin_probe,
+ .config_aneg = adin_config_aneg,
+ .read_status = adin_read_status,
+ .set_loopback = adin_set_loopback,
+ .suspend = adin_suspend,
+ .resume = adin_resume,
+ },
+};
+
+module_phy_driver(adin_driver);
+
+static struct mdio_device_id __maybe_unused adin_tbl[] = {
+ { PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(mdio, adin_tbl);
+MODULE_DESCRIPTION("Analog Devices Industrial Ethernet T1L PHY driver");
+MODULE_LICENSE("Dual BSD/GPL");