@@ -60,5 +60,6 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-b.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-cm4.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-bpi-r2-pro.dtb
new file mode 100644
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+ model = "Pine64 RK3566 SoQuartz with CM4-IO Carrier Board";
+ compatible = "pine64,soquartz-cm4io", "pine64,soquartz", "rockchip,rk3566";
+
+ /* labeled +12v in schematic */
+ vcc12v_dcin: vcc12v-dcin-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ /* labeled +5v in schematic */
+ vcc_5v: vcc-5v-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+};
+
+&gmac1 {
+ status = "okay";
+};
+
+/* i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+ status = "okay";
+
+ /* the rtc interrupt is tied to PMIC_PWRON,
+ * it will force reset the board if triggered.
+ */
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063";
+ reg = <0x51>;
+ };
+};
+
+/* i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+ status = "disabled";
+};
+
+/* i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+ status = "disabled";
+};
+
+/* i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+ status = "disabled";
+};
+
+/* i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6 - i2s1_sdi2_m1
+ * pin 40 - GPIO9 - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3 - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+ status = "disabled";
+};
+
+&led_diy {
+ status = "okay";
+};
+
+&led_work {
+ status = "okay";
+};
+
+&rgmii_phy1 {
+ status = "okay";
+};
+
+/* saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+ status = "disabled";
+};
+
+&sdmmc0 {
+ vmmc-supply = <&sdmmc_pwr>;
+ status = "okay";
+};
+
+&sdmmc_pwr {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ status = "okay";
+};
+
+/* spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7 - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8 - spi3_cs0_m0
+ * pin 40 - GPIO9 - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+ status = "disabled";
+};
+
+/* uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+ status = "okay";
+};
+
+/* uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc_5v>;
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ status = "okay";
+};
+
+&vbus {
+ vin-supply = <&vcc_5v>;
+};
new file mode 100644
@@ -0,0 +1,607 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3566.dtsi"
+
+/ {
+ model = "Pine64 RK3566 SoQuartz SOM";
+ compatible = "pine64,soquartz", "rockchip,rk3566";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdmmc0;
+ mmc1 = &sdhci;
+ mmc2 = &sdmmc1;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac1_clkin: external-gmac1-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac1_clkin";
+ #clock-cells = <0>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_diy: led-diy {
+ label = "diy-led";
+ default-state = "on";
+ gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&diy_led_enable_h>;
+ retain-state-suspended;
+ status = "disabled";
+ };
+
+ led_work: led-work {
+ label = "work-led";
+ default-state = "off";
+ gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&work_led_enable_h>;
+ retain-state-suspended;
+ status = "disabled";
+ };
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ status = "okay";
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+
+ vbus: vbus-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ /* sourced from vbus, vbus is provided by the carrier board */
+ vcc5v0_sys: vcc5v0-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vbus>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ sdmmc_pwr: sdmmc-pwr-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_pwr_h>;
+ regulator-name = "sdmmc_pwr";
+ status = "disabled";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_3v3>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m0_miim
+ &gmac1m0_tx_bus2
+ &gmac1m0_rx_bus2
+ &gmac1m0_rgmii_clk
+ &gmac1m0_clkinout
+ &gmac1m0_rgmii_bus>;
+ snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f, also works well here */
+ snps,reset-delays-us = <0 20000 100000>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ phy-handle = <&rgmii_phy1>;
+ status = "disabled";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vdd_npu";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda0v9_image";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda_0v9";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdda0v9_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_acodec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pmu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca_1v8";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pmu";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_image";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ status = "disabled";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ };
+ };
+};
+
+/* i2c1 is exposed on CM1 / Module1A
+ * pin 80 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+ status = "disabled";
+};
+
+/* i2c2 is exposed on CM1 / Module1A
+ * pin 56 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2m1_xfer>;
+ status = "disabled";
+};
+
+/* i2c3 is exposed on CM1 / Module1A
+ * pin 35 - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+ status = "disabled";
+};
+
+/* i2c4 is exposed on CM2 / Module1B
+ * pin 45 - i2c4_scl_m1
+ * pin 47 - i2c4_sda_m1
+ */
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4m1_xfer>;
+ status = "disabled";
+};
+
+/* i2s1_8ch is exposed on CM1 / Module1A
+ * pin 24 - i2s1_sdi1_m1
+ * pin 25 - i2s1_sdo0_m1
+ * pin 26 - i2s1_lrck_tx_m1
+ * pin 27 - i2s1_sdi0_m1
+ * pin 29 - i2s1_sdi3_m1
+ * pin 30 - i2s1_sdi2_m1
+ * pin 40 - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - i2s1_sdo2_m1
+ * pin 49 - i2s1_sclk_tx_m1
+ * pin 50 - i2s1_mclk_m1
+ * pin 56 - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m1_sclktx &i2s1m1_sclkrx
+ &i2s1m1_lrcktx &i2s1m1_lrckrx
+ &i2s1m1_sdi0 &i2s1m1_sdi1
+ &i2s1m1_sdi2 &i2s1m1_sdi3
+ &i2s1m1_sdo0 &i2s1m1_sdo1
+ &i2s1m1_sdo2 &i2s1m1_sdo3>;
+ status = "disabled";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ status = "disabled";
+ };
+};
+
+&pinctrl {
+ bt {
+ bt_enable_h: bt-enable-h {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_host_wake_l: bt-host-wake-l {
+ rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ bt_wake_l: bt-wake-l {
+ rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ work_led_enable_h: work-led-enable-h {
+ rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ diy_led_enable_h: diy-led-enable-h {
+ rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdio-pwrseq {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc-pwr {
+ sdmmc_pwr_h: sdmmc-pwr-h {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vcc_3v3>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_3v3>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+/* saradc is exposed on CM1 / Module1A
+ * pin 94 - saradc_vin3
+ * pin 96 - saradc_vin2
+ */
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "disabled";
+};
+
+&sdhci {
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ broken-cd;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "disabled";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sys>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+/* spi3 is exposed on CM1 / Module1A
+ * pin 37 - spi3_cs1_m0
+ * pin 38 - spi3_clk_m0
+ * pin 39 - spi3_cs0_m0
+ * pin 40 - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - spi3_mosi_m0
+ */
+&spi3 {
+ status = "disabled";
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&rk809 1>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+ host-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+ vbat-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcca1v8_pmu>;
+ };
+};
+
+/* uart2 is exposed on CM1 / Module1A
+ * pin 51 - uart2_rx_m0
+ * pin 55 - uart2_tx_m0
+ */
+&uart2 {
+ status = "disabled";
+};
+
+/* uart7 is exposed on CM1 / Module1A
+ * pin 46 - uart7_tx_m2
+ * pin 47 - uart7_rx_m2
+ */
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7m2_xfer>;
+ status = "disabled";
+};
+
+/* dwc3_otg is the only usb port available */
+&usb2phy0 {
+ status = "disabled";
+};
+
+&usb2phy0_otg {
+ status = "disabled";
+};
+
+&usb_host0_xhci {
+ status = "disabled";
+};
This is the initial SoQuartz SoM device tree on a CM4IO carrier board. This board outputs debug on uart2 and supports the following components: Gigabit Ethernet USB2 (OTG/Host shared) PCIe 2.0 x1 HDMI (HDMI Port 0) eDP (HDMI Port 1) DSI (RPi compatible pinout) CSI (RPi compatible pinout) A/B/G/N WiFi Bluetooth SDMMC eMMC SPI NOR Flash (Not placed) PI-40 compatible pin header Signed-off-by: Peter Geis <pgwipeout@gmail.com> --- arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/rk3566-soquartz-cm4.dts | 167 +++++ .../boot/dts/rockchip/rk3566-soquartz.dtsi | 607 ++++++++++++++++++ 3 files changed, 775 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-soquartz-cm4.dts create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-soquartz.dtsi