@@ -45,20 +45,20 @@ additionalProperties: false
examples:
# Example 1: apps bcm_voter on SDM845 SoC should be defined inside &apps_rsc node
- # as defined in Documentation/devicetree/bindings/soc/qcom/rpmh-rsc.txt
+ # as defined in Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml
- |
- apps_bcm_voter: bcm_voter {
+ apps_bcm_voter: bcm-voter {
compatible = "qcom,bcm-voter";
};
# Example 2: disp bcm_voter on SDM845 should be defined inside &disp_rsc node
- # as defined in Documentation/devicetree/bindings/soc/qcom/rpmh-rsc.txt
+ # as defined in Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml
- |
#include <dt-bindings/interconnect/qcom,icc.h>
- disp_bcm_voter: bcm_voter {
+ disp_bcm_voter: bcm-voter {
compatible = "qcom,bcm-voter";
qcom,tcs-wait = <QCOM_ICC_TAG_AMC>;
};
new file mode 100644
@@ -0,0 +1,272 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/qcom/qcom,rpmh-rsc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm RPMH RSC
+
+maintainers:
+ - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: |
+ Resource Power Manager Hardened (RPMH) is the mechanism for communicating
+ with the hardened resource accelerators on Qualcomm SoCs. Requests to the
+ resources can be written to the Trigger Command Set (TCS) registers and
+ using a (addr, val) pair and triggered. Messages in the TCS are then sent in
+ sequence over an internal bus.
+
+ The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity
+ (Resource State Coordinator a.k.a RSC) that can handle multiple sleep and
+ active/wake resource requests. Multiple such DRVs can exist in a SoC and can
+ be written to from Linux. The structure of each DRV follows the same template
+ with a few variations that are captured by the properties here.
+
+ A TCS may be triggered from Linux or triggered by the F/W after all the CPUs
+ have powered off to facilitate idle power saving. TCS could be classified as::
+ ACTIVE - Triggered by Linux
+ SLEEP - Triggered by F/W
+ WAKE - Triggered by F/W
+ CONTROL - Triggered by F/W
+ See also:: <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+ The order in which they are described in the DT, should match the hardware
+ configuration.
+
+ Requests can be made for the state of a resource, when the subsystem is
+ active or idle. When all subsystems like Modem, GPU, CPU are idle, the
+ resource state will be an aggregate of the sleep votes from each of those
+ subsystems. Clients may request a sleep value for their shared resources in
+ addition to the active mode requests.
+
+ Drivers that want to use the RSC to communicate with RPMH must specify their
+ bindings as child nodes of the RSC controllers they wish to communicate with.
+
+properties:
+ compatible:
+ const: qcom,rpmh-rsc
+
+ interrupts:
+ minItems: 1
+ maxItems: 4
+ description:
+ The interrupt that trips when a message complete/response is received for
+ this DRV from the accelerators.
+ Number of interrupts must match number of DRV blocks.
+
+ label:
+ description:
+ Name for the RSC. The name would be used in trace logs.
+
+ qcom,drv-id:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The ID of the DRV in the RSC block that will be used by this controller.
+
+ qcom,tcs-config:
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ - items:
+ - description: TCS type
+ enum: [ 0, 1, 2, 3 ]
+ - description: Number of TCS
+ - items:
+ - description: TCS type
+ enum: [ 0, 1, 2, 3 ]
+ - description: Number of TCS
+ - items:
+ - description: TCS type
+ enum: [ 0, 1, 2, 3]
+ - description: Numbe r of TCS
+ - items:
+ - description: TCS type
+ enum: [ 0, 1, 2, 3 ]
+ - description: Number of TCS
+ description: |
+ The tuple defining the configuration of TCS. Must have two cells which
+ describe each TCS type. The order of the TCS must match the hardware
+ configuration.
+ Cell 1 (TCS Type):: TCS types to be specified::
+ - ACTIVE_TCS
+ - SLEEP_TCS
+ - WAKE_TCS
+ - CONTROL_TCS
+ Cell 2 (Number of TCS):: <u32>
+
+ qcom,tcs-offset:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The offset of the TCS blocks.
+
+ reg:
+ minItems: 1
+ maxItems: 4
+
+ reg-names:
+ minItems: 1
+ items:
+ - const: drv-0
+ - const: drv-1
+ - const: drv-2
+ - const: drv-3
+
+ bcm-voter:
+ $ref: /schemas/interconnect/qcom,bcm-voter.yaml#
+
+ clock-controller:
+ $ref: /schemas/clock/qcom,rpmhcc.yaml#
+
+ power-controller:
+ $ref: /schemas/power/qcom,rpmpd.yaml#
+
+patternProperties:
+ '-regulators$':
+ $ref: /schemas/regulator/qcom,rpmh-regulator.yaml#
+
+required:
+ - compatible
+ - interrupts
+ - qcom,drv-id
+ - qcom,tcs-config
+ - qcom,tcs-offset
+ - reg
+ - reg-names
+
+additionalProperties: false
+
+examples:
+ - |
+ // For a TCS whose RSC base address is 0x179C0000 and is at a DRV id of
+ // 2, the register offsets for DRV2 start at 0D00, the register
+ // calculations are like this::
+ // DRV0: 0x179C0000
+ // DRV2: 0x179C0000 + 0x10000 = 0x179D0000
+ // DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000
+ // TCS-OFFSET: 0xD00
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+ rsc@179c0000 {
+ compatible = "qcom,rpmh-rsc";
+ reg = <0x179c0000 0x10000>,
+ <0x179d0000 0x10000>,
+ <0x179e0000 0x10000>;
+ reg-names = "drv-0", "drv-1", "drv-2";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ label = "apps_rsc";
+ qcom,tcs-offset = <0xd00>;
+ qcom,drv-id = <2>;
+ qcom,tcs-config = <ACTIVE_TCS 2>,
+ <SLEEP_TCS 3>,
+ <WAKE_TCS 3>,
+ <CONTROL_TCS 1>;
+ };
+
+ - |
+ // For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the
+ // register offsets for DRV0 start at 01C00, the register calculations are
+ // like this::
+ // DRV0: 0xAF20000
+ // TCS-OFFSET: 0x1C00
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+ rsc@af20000 {
+ compatible = "qcom,rpmh-rsc";
+ reg = <0xaf20000 0x10000>;
+ reg-names = "drv-0";
+ interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
+ label = "disp_rsc";
+ qcom,tcs-offset = <0x1c00>;
+ qcom,drv-id = <0>;
+ qcom,tcs-config = <ACTIVE_TCS 0>,
+ <SLEEP_TCS 1>,
+ <WAKE_TCS 1>,
+ <CONTROL_TCS 0>;
+ };
+
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/soc/qcom,rpmh-rsc.h>
+ #include <dt-bindings/power/qcom-rpmpd.h>
+
+ rsc@18200000 {
+ compatible = "qcom,rpmh-rsc";
+ reg = <0x18200000 0x10000>,
+ <0x18210000 0x10000>,
+ <0x18220000 0x10000>;
+ reg-names = "drv-0", "drv-1", "drv-2";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ label = "apps_rsc";
+ qcom,tcs-offset = <0xd00>;
+ qcom,drv-id = <2>;
+ qcom,tcs-config = <ACTIVE_TCS 2>,
+ <SLEEP_TCS 3>,
+ <WAKE_TCS 3>,
+ <CONTROL_TCS 0>;
+
+ clock-controller {
+ compatible = "qcom,sm8350-rpmh-clk";
+ #clock-cells = <1>;
+ clock-names = "xo";
+ clocks = <&xo_board>;
+ };
+
+ power-controller {
+ compatible = "qcom,sm8350-rpmhpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmhpd_opp_table>;
+
+ rpmhpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmhpd_opp_ret: opp1 {
+ opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+ };
+
+ rpmhpd_opp_min_svs: opp2 {
+ opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+ };
+
+ rpmhpd_opp_low_svs: opp3 {
+ opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+ };
+
+ rpmhpd_opp_svs: opp4 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+ };
+
+ rpmhpd_opp_svs_l1: opp5 {
+ opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+ };
+
+ rpmhpd_opp_nom: opp6 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+ };
+
+ rpmhpd_opp_nom_l1: opp7 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+ };
+
+ rpmhpd_opp_nom_l2: opp8 {
+ opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+ };
+
+ rpmhpd_opp_turbo: opp9 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+ };
+
+ rpmhpd_opp_turbo_l1: opp10 {
+ opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+ };
+ };
+ };
+
+ bcm-voter {
+ compatible = "qcom,bcm-voter";
+ };
+ };
deleted file mode 100644
@@ -1,137 +0,0 @@
-RPMH RSC:
-------------
-
-Resource Power Manager Hardened (RPMH) is the mechanism for communicating with
-the hardened resource accelerators on Qualcomm SoCs. Requests to the resources
-can be written to the Trigger Command Set (TCS) registers and using a (addr,
-val) pair and triggered. Messages in the TCS are then sent in sequence over an
-internal bus.
-
-The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity
-(Resource State Coordinator a.k.a RSC) that can handle multiple sleep and
-active/wake resource requests. Multiple such DRVs can exist in a SoC and can
-be written to from Linux. The structure of each DRV follows the same template
-with a few variations that are captured by the properties here.
-
-A TCS may be triggered from Linux or triggered by the F/W after all the CPUs
-have powered off to facilitate idle power saving. TCS could be classified as -
-
- ACTIVE /* Triggered by Linux */
- SLEEP /* Triggered by F/W */
- WAKE /* Triggered by F/W */
- CONTROL /* Triggered by F/W */
-
-The order in which they are described in the DT, should match the hardware
-configuration.
-
-Requests can be made for the state of a resource, when the subsystem is active
-or idle. When all subsystems like Modem, GPU, CPU are idle, the resource state
-will be an aggregate of the sleep votes from each of those subsystems. Clients
-may request a sleep value for their shared resources in addition to the active
-mode requests.
-
-Properties:
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: Should be "qcom,rpmh-rsc".
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: The first register specifies the base address of the
- DRV(s). The number of DRVs in the dependent on the RSC.
- The tcs-offset specifies the start address of the
- TCS in the DRVs.
-
-- reg-names:
- Usage: required
- Value type: <string>
- Definition: Maps the register specified in the reg property. Must be
- "drv-0", "drv-1", "drv-2" etc and "tcs-offset". The
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-interrupt>
- Definition: The interrupt that trips when a message complete/response
- is received for this DRV from the accelerators.
-
-- qcom,drv-id:
- Usage: required
- Value type: <u32>
- Definition: The id of the DRV in the RSC block that will be used by
- this controller.
-
-- qcom,tcs-config:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: The tuple defining the configuration of TCS.
- Must have 2 cells which describe each TCS type.
- <type number_of_tcs>.
- The order of the TCS must match the hardware
- configuration.
- - Cell #1 (TCS Type): TCS types to be specified -
- ACTIVE_TCS
- SLEEP_TCS
- WAKE_TCS
- CONTROL_TCS
- - Cell #2 (Number of TCS): <u32>
-
-- label:
- Usage: optional
- Value type: <string>
- Definition: Name for the RSC. The name would be used in trace logs.
-
-Drivers that want to use the RSC to communicate with RPMH must specify their
-bindings as child nodes of the RSC controllers they wish to communicate with.
-
-Example 1:
-
-For a TCS whose RSC base address is is 0x179C0000 and is at a DRV id of 2, the
-register offsets for DRV2 start at 0D00, the register calculations are like
-this -
-DRV0: 0x179C0000
-DRV2: 0x179C0000 + 0x10000 = 0x179D0000
-DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000
-TCS-OFFSET: 0xD00
-
- apps_rsc: rsc@179c0000 {
- label = "apps_rsc";
- compatible = "qcom,rpmh-rsc";
- reg = <0x179c0000 0x10000>,
- <0x179d0000 0x10000>,
- <0x179e0000 0x10000>;
- reg-names = "drv-0", "drv-1", "drv-2";
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
- qcom,tcs-offset = <0xd00>;
- qcom,drv-id = <2>;
- qcom,tcs-config = <ACTIVE_TCS 2>,
- <SLEEP_TCS 3>,
- <WAKE_TCS 3>,
- <CONTROL_TCS 1>;
- };
-
-Example 2:
-
-For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the
-register offsets for DRV0 start at 01C00, the register calculations are like
-this -
-DRV0: 0xAF20000
-TCS-OFFSET: 0x1C00
-
- disp_rsc: rsc@af20000 {
- label = "disp_rsc";
- compatible = "qcom,rpmh-rsc";
- reg = <0xaf20000 0x10000>;
- reg-names = "drv-0";
- interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
- qcom,tcs-offset = <0x1c00>;
- qcom,drv-id = <0>;
- qcom,tcs-config = <ACTIVE_TCS 0>,
- <SLEEP_TCS 1>,
- <WAKE_TCS 1>,
- <CONTROL_TCS 0>;
- };
Convert the Qualcomm RPMH RSC bindings to DT Schema. Changes against original bindings: 1. Add qcom,tcs-offset as a property instead of one of reg (not used that way). 2. Add limits to interrupts. 3. Add child nodes (bcm-voter, clock-controller, power-controller). 4. Extend the example with more complex one. The device description and DTS examples were copied from existing sources, so keep the license as GPL-2.0-only. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- .../bindings/interconnect/qcom,bcm-voter.yaml | 8 +- .../bindings/soc/qcom/qcom,rpmh-rsc.yaml | 272 ++++++++++++++++++ .../devicetree/bindings/soc/qcom/rpmh-rsc.txt | 137 --------- 3 files changed, 276 insertions(+), 141 deletions(-) create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,rpmh-rsc.yaml delete mode 100644 Documentation/devicetree/bindings/soc/qcom/rpmh-rsc.txt