deleted file mode 100644
@@ -1,74 +0,0 @@
-Tegra SOC USB PHY
-
-The device node for Tegra SOC USB PHY:
-
-Required properties :
- - compatible : For Tegra20, must contain "nvidia,tegra20-usb-phy".
- For Tegra30, must contain "nvidia,tegra30-usb-phy". Otherwise, must contain
- "nvidia,<chip>-usb-phy" plus at least one of the above, where <chip> is
- tegra114, tegra124, tegra132, or tegra210.
- - reg : Defines the following set of registers, in the order listed:
- - The PHY's own register set.
- Always present.
- - The register set of the PHY containing the UTMI pad control registers.
- Present if-and-only-if phy_type == utmi.
- - phy_type : Should be one of "utmi", "ulpi" or "hsic".
- - clocks : Defines the clocks listed in the clock-names property.
- - clock-names : The following clock names must be present:
- - reg: The clock needed to access the PHY's own registers. This is the
- associated EHCI controller's clock. Always present.
- - pll_u: PLL_U. Always present.
- - timer: The timeout clock (clk_m). Present if phy_type == utmi.
- - utmi-pads: The clock needed to access the UTMI pad control registers.
- Present if phy_type == utmi.
- - ulpi-link: The clock Tegra provides to the ULPI PHY (usually pad DAP_MCLK2
- with pad group aka "nvidia,pins" cdev2 and pin mux option config aka
- "nvidia,function" pllp_out4).
- Present if phy_type == ulpi, and ULPI link mode is in use.
- - resets : Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names : Must include the following entries:
- - usb: The PHY's own reset signal.
- - utmi-pads: The reset of the PHY containing the chip-wide UTMI pad control
- registers. Required even if phy_type == ulpi.
-
-Required properties for phy_type == ulpi:
- - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
-
-Required PHY timing params for utmi phy, for all chips:
- - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before
- start of sync launches RxActive
- - nvidia,elastic-limit : Variable FIFO Depth of elastic input store
- - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait
- before declare IDLE.
- - nvidia,term-range-adj : Range adjusment on terminations
- - Either one of the following for HS driver output control:
- - nvidia,xcvr-setup : integer, uses the provided value.
- - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read
- from the on-chip fuses
- If both are provided, nvidia,xcvr-setup-use-fuses takes precedence.
- - nvidia,xcvr-lsfslew : LS falling slew rate control.
- - nvidia,xcvr-lsrslew : LS rising slew rate control.
-
-Required PHY timing params for utmi phy, only on Tegra30 and above:
- - nvidia,xcvr-hsslew : HS slew rate control.
- - nvidia,hssquelch-level : HS squelch detector level.
- - nvidia,hsdiscon-level : HS disconnect detector level.
-
-Optional properties:
- - nvidia,has-legacy-mode : boolean indicates whether this controller can
- operate in legacy mode (as APX 2500 / 2600). In legacy mode some
- registers are accessed through the APB_MISC base address instead of
- the USB controller.
- - nvidia,is-wired : boolean. Indicates whether we can do certain kind of power
- optimizations for the devices that are always connected. e.g. modem.
- - dr_mode : dual role mode. Indicates the working mode for the PHY. Can be
- "host", "peripheral", or "otg". Defaults to "host" if not defined.
- host means this is a host controller
- peripheral means it is device controller
- otg means it can operate as either ("on the go")
- - nvidia,has-utmi-pad-registers : boolean indicates whether this controller
- contains the UTMI pad control registers common to all USB controllers.
-
-VBUS control (required for dr_mode == otg, optional for dr_mode == host):
- - vbus-supply: regulator for VBUS
new file mode 100644
@@ -0,0 +1,357 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/nvidia,tegra20-usb-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NVIDIA Tegra USB PHY
+
+maintainers:
+ - Dmitry Osipenko <digetx@gmail.com>
+ - Jon Hunter <jonathanh@nvidia.com>
+ - Thierry Reding <thierry.reding@gmail.com>
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - nvidia,tegra124-usb-phy
+ - nvidia,tegra114-usb-phy
+ - enum:
+ - nvidia,tegra30-usb-phy
+ - items:
+ - enum:
+ - nvidia,tegra30-usb-phy
+ - nvidia,tegra20-usb-phy
+
+ reg:
+ minItems: 1
+ maxItems: 2
+ description: |
+ PHY0 and PHY2 share power and ground, PHY0 contains shared registers.
+ PHY0 and PHY2 must specify two register sets, where the first set is
+ PHY own registers and the second set is the PHY0 registers.
+
+ clocks:
+ anyOf:
+ - items:
+ - description: Registers clock
+ - description: Main PHY clock
+
+ - items:
+ - description: Registers clock
+ - description: Main PHY clock
+ - description: ULPI PHY clock
+
+ - items:
+ - description: Registers clock
+ - description: Main PHY clock
+ - description: UTMI pads control registers clock
+
+ - items:
+ - description: Registers clock
+ - description: Main PHY clock
+ - description: UTMI timeout clock
+ - description: UTMI pads control registers clock
+
+ clock-names:
+ oneOf:
+ - items:
+ - const: reg
+ - const: pll_u
+
+ - items:
+ - const: reg
+ - const: pll_u
+ - const: ulpi-link
+
+ - items:
+ - const: reg
+ - const: pll_u
+ - const: utmi-pads
+
+ - items:
+ - const: reg
+ - const: pll_u
+ - const: timer
+ - const: utmi-pads
+
+ resets:
+ oneOf:
+ - maxItems: 1
+ description: PHY reset
+
+ - items:
+ - description: PHY reset
+ - description: UTMI pads reset
+
+ reset-names:
+ oneOf:
+ - const: usb
+
+ - items:
+ - const: usb
+ - const: utmi-pads
+
+ "#phy-cells":
+ const: 0
+
+ phy_type:
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [utmi, ulpi, hsic]
+
+ dr_mode:
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [host, peripheral, otg]
+ default: host
+
+ vbus-supply:
+ description: Regulator controlling USB VBUS.
+
+ nvidia,has-legacy-mode:
+ description: |
+ Indicates whether this controller can operate in legacy mode
+ (as APX 2500 / 2600). In legacy mode some registers are accessed
+ through the APB_MISC base address instead of the USB controller.
+ type: boolean
+
+ nvidia,is-wired:
+ description: |
+ Indicates whether we can do certain kind of power optimizations for
+ the devices that are always connected. e.g. modem.
+ type: boolean
+
+ nvidia,has-utmi-pad-registers:
+ description: |
+ Indicates whether this controller contains the UTMI pad control
+ registers common to all USB controllers.
+ type: boolean
+
+ nvidia,hssync-start-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 31
+ description: |
+ Number of 480 MHz clock cycles to wait before start of sync launches
+ RxActive.
+
+ nvidia,elastic-limit:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 31
+ description: Variable FIFO Depth of elastic input store.
+
+ nvidia,idle-wait-delay:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 31
+ description: |
+ Number of 480 MHz clock cycles of idle to wait before declare IDLE.
+
+ nvidia,term-range-adj:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+ description: Range adjustment on terminations.
+
+ nvidia,xcvr-setup:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 127
+ description: Input of XCVR cell, HS driver output control.
+
+ nvidia,xcvr-setup-use-fuses:
+ description: Indicates that the value is read from the on-chip fuses.
+ type: boolean
+
+ nvidia,xcvr-lsfslew:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ description: LS falling slew rate control.
+
+ nvidia,xcvr-lsrslew:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ description: LS rising slew rate control.
+
+ nvidia,xcvr-hsslew:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 511
+ description: HS slew rate control.
+
+ nvidia,hssquelch-level:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ description: HS squelch detector level.
+
+ nvidia,hsdiscon-level:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 7
+ description: HS disconnect detector level.
+
+ nvidia,phy-reset-gpio:
+ maxItems: 1
+ description: GPIO used to reset the PHY.
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - resets
+ - reset-names
+ - "#phy-cells"
+ - phy_type
+
+additionalProperties: false
+
+allOf:
+ - if:
+ properties:
+ phy_type:
+ const: utmi
+
+ then:
+ properties:
+ reg:
+ minItems: 2
+ maxItems: 2
+
+ resets:
+ maxItems: 2
+
+ reset-names:
+ maxItems: 2
+
+ required:
+ - nvidia,hssync-start-delay
+ - nvidia,elastic-limit
+ - nvidia,idle-wait-delay
+ - nvidia,term-range-adj
+ - nvidia,xcvr-lsfslew
+ - nvidia,xcvr-lsrslew
+
+ anyOf:
+ - required: ["nvidia,xcvr-setup"]
+ - required: ["nvidia,xcvr-setup-use-fuses"]
+
+ if:
+ properties:
+ compatible:
+ contains:
+ const: nvidia,tegra30-usb-phy
+
+ then:
+ properties:
+ clocks:
+ maxItems: 3
+
+ clock-names:
+ items:
+ - const: reg
+ - const: pll_u
+ - const: utmi-pads
+
+ required:
+ - nvidia,xcvr-hsslew
+ - nvidia,hssquelch-level
+ - nvidia,hsdiscon-level
+
+ else:
+ properties:
+ clocks:
+ maxItems: 4
+
+ clock-names:
+ items:
+ - const: reg
+ - const: pll_u
+ - const: timer
+ - const: utmi-pads
+
+ - if:
+ properties:
+ phy_type:
+ const: ulpi
+
+ then:
+ properties:
+ reg:
+ minItems: 1
+ maxItems: 1
+
+ clocks:
+ minItems: 2
+ maxItems: 3
+
+ clock-names:
+ minItems: 2
+ maxItems: 3
+
+ oneOf:
+ - items:
+ - const: reg
+ - const: pll_u
+
+ - items:
+ - const: reg
+ - const: pll_u
+ - const: ulpi-link
+
+ resets:
+ minItems: 1
+ maxItems: 2
+
+ reset-names:
+ minItems: 1
+ maxItems: 2
+
+examples:
+ - |
+ #include <dt-bindings/clock/tegra124-car.h>
+
+ usb-phy@7d008000 {
+ compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
+ reg = <0x7d008000 0x4000>,
+ <0x7d000000 0x4000>;
+ phy_type = "utmi";
+ clocks = <&tegra_car TEGRA124_CLK_USB3>,
+ <&tegra_car TEGRA124_CLK_PLL_U>,
+ <&tegra_car TEGRA124_CLK_USBD>;
+ clock-names = "reg", "pll_u", "utmi-pads";
+ resets = <&tegra_car 59>, <&tegra_car 22>;
+ reset-names = "usb", "utmi-pads";
+ #phy-cells = <0>;
+ nvidia,hssync-start-delay = <0>;
+ nvidia,idle-wait-delay = <17>;
+ nvidia,elastic-limit = <16>;
+ nvidia,term-range-adj = <6>;
+ nvidia,xcvr-setup = <9>;
+ nvidia,xcvr-lsfslew = <0>;
+ nvidia,xcvr-lsrslew = <3>;
+ nvidia,hssquelch-level = <2>;
+ nvidia,hsdiscon-level = <5>;
+ nvidia,xcvr-hsslew = <12>;
+ };
+
+ - |
+ #include <dt-bindings/clock/tegra20-car.h>
+
+ usb-phy@c5004000 {
+ compatible = "nvidia,tegra20-usb-phy";
+ reg = <0xc5004000 0x4000>;
+ phy_type = "ulpi";
+ clocks = <&tegra_car TEGRA20_CLK_USB2>,
+ <&tegra_car TEGRA20_CLK_PLL_U>,
+ <&tegra_car TEGRA20_CLK_CDEV2>;
+ clock-names = "reg", "pll_u", "ulpi-link";
+ resets = <&tegra_car 58>, <&tegra_car 22>;
+ reset-names = "usb", "utmi-pads";
+ #phy-cells = <0>;
+ };