diff mbox series

[v2,10/13] dt-bindings: spi: cadence-qspi: Add support for Pensando Elba SoC

Message ID 20210329015938.20316-11-brad@pensando.io
State New
Headers show
Series None | expand

Commit Message

Brad Larson March 29, 2021, 1:59 a.m. UTC
Add new vendor Pensando Systems Elba SoC compatible
string and convert to json-schema.

Signed-off-by: Brad Larson <brad@pensando.io>
---
 .../bindings/spi/cadence-quadspi.txt          |  68 --------
 .../bindings/spi/cadence-quadspi.yaml         | 153 ++++++++++++++++++
 2 files changed, 153 insertions(+), 68 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
 create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml

Comments

Brad Larson March 30, 2021, 2:12 a.m. UTC | #1
On Mon, Mar 29, 2021 at 9:01 AM Mark Brown <broonie@kernel.org> wrote:
>

> On Sun, Mar 28, 2021 at 06:59:35PM -0700, Brad Larson wrote:

> > Add new vendor Pensando Systems Elba SoC compatible

> > string and convert to json-schema.

>

> These are two unrelated changes and should be separate patches, again as

> covered in submitting-patches.rst.  It is generally better to do the

> changes adding new stuff first and then convert to YAML as the final

> patches as the series since there is often a delay on reviews of YAML

> conversions.


The initial patch set only changed the text file and a request was made
to convert to YAML.  I'll change this particular patch to modify just the
text file as before and then the convert to YAML with a later patch in the set.
Pratyush Yadav March 30, 2021, 11:12 a.m. UTC | #2
Hi Brad,

On 28/03/21 06:59PM, Brad Larson wrote:
> Add new vendor Pensando Systems Elba SoC compatible
> string and convert to json-schema.
> 
> Signed-off-by: Brad Larson <brad@pensando.io>
> ---
>  .../bindings/spi/cadence-quadspi.txt          |  68 --------
>  .../bindings/spi/cadence-quadspi.yaml         | 153 ++++++++++++++++++
>  2 files changed, 153 insertions(+), 68 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>  create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> 
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> deleted file mode 100644
> index 8ace832a2d80..000000000000
> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> +++ /dev/null
> @@ -1,68 +0,0 @@
> -* Cadence Quad SPI controller
> -
> -Required properties:
> -- compatible : should be one of the following:
> -	Generic default - "cdns,qspi-nor".
> -	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> -	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
> -	For Intel LGM SoC - "intel,lgm-qspi", "cdns,qspi-nor".
> -- reg : Contains two entries, each of which is a tuple consisting of a
> -	physical address and length. The first entry is the address and
> -	length of the controller register set. The second entry is the
> -	address and length of the QSPI Controller data area.
> -- interrupts : Unit interrupt specifier for the controller interrupt.
> -- clocks : phandle to the Quad SPI clock.
> -- cdns,fifo-depth : Size of the data FIFO in words.
> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
> -
> -Optional properties:
> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
> -  the read data rather than the QSPI clock. Make sure that QSPI return
> -  clock is populated on the board before using this property.
> -
> -Optional subnodes:
> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
> -custom properties:
> -- cdns,read-delay : Delay for read capture logic, in clock cycles
> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
> -                  mode chip select outputs are de-asserted between
> -		  transactions.
> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
> -                  de-activated and the activation of another.
> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
> -                  transaction and deasserting the device chip select
> -		  (qspi_n_ss_out).
> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
> -                  and first bit transfer.
> -- resets	: Must contain an entry for each entry in reset-names.
> -		  See ../reset/reset.txt for details.
> -- reset-names	: Must include either "qspi" and/or "qspi-ocp".
> -
> -Example:
> -
> -	qspi: spi@ff705000 {
> -		compatible = "cdns,qspi-nor";
> -		#address-cells = <1>;
> -		#size-cells = <0>;
> -		reg = <0xff705000 0x1000>,
> -		      <0xffa00000 0x1000>;
> -		interrupts = <0 151 4>;
> -		clocks = <&qspi_clk>;
> -		cdns,is-decoded-cs;
> -		cdns,fifo-depth = <128>;
> -		cdns,fifo-width = <4>;
> -		cdns,trigger-address = <0x00000000>;
> -		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
> -		reset-names = "qspi", "qspi-ocp";
> -
> -		flash0: n25q00@0 {
> -			...
> -			cdns,read-delay = <4>;
> -			cdns,tshsl-ns = <50>;
> -			cdns,tsd2d-ns = <50>;
> -			cdns,tchsh-ns = <4>;
> -			cdns,tslch-ns = <4>;
> -		};
> -	};
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> new file mode 100644
> index 000000000000..94d631045153
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
> @@ -0,0 +1,153 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Cadence Quad SPI controller
> +
> +maintainers:
> +  - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
> +  - Brad Larson <brad@pensando.io>
> +
> +properties:
> +  compatible:
> +    contains:
> +      enum:
> +        - cdns,qspi-nor       # Generic default
> +        - ti,k2g-qspi         # TI 66AK2G SoC
> +        - ti,am654-ospi       # TI AM654 SoC
> +        - intel,lgm-qspi      # Intel LGM SoC
> +        - pensando,cdns-qspi  # Pensando Elba SoC

Wouldn't this allow any combination of all 5 strings? So for example 
this would allow "ti,am654-ospi", "pensando,cdns-qspi" which is 
obviously not correct.

I sent a patch recently [0] that does this correctly and it has gotten 
Rob's blessing. So I suggest you build your patch on top of that.

[...]

[0] https://patchwork.kernel.org/project/spi-devel-general/patch/20210326130034.15231-5-p.yadav@ti.com/
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
deleted file mode 100644
index 8ace832a2d80..000000000000
--- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
+++ /dev/null
@@ -1,68 +0,0 @@ 
-* Cadence Quad SPI controller
-
-Required properties:
-- compatible : should be one of the following:
-	Generic default - "cdns,qspi-nor".
-	For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
-	For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
-	For Intel LGM SoC - "intel,lgm-qspi", "cdns,qspi-nor".
-- reg : Contains two entries, each of which is a tuple consisting of a
-	physical address and length. The first entry is the address and
-	length of the controller register set. The second entry is the
-	address and length of the QSPI Controller data area.
-- interrupts : Unit interrupt specifier for the controller interrupt.
-- clocks : phandle to the Quad SPI clock.
-- cdns,fifo-depth : Size of the data FIFO in words.
-- cdns,fifo-width : Bus width of the data FIFO in bytes.
-- cdns,trigger-address : 32-bit indirect AHB trigger address.
-
-Optional properties:
-- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
-- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
-  the read data rather than the QSPI clock. Make sure that QSPI return
-  clock is populated on the board before using this property.
-
-Optional subnodes:
-Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
-custom properties:
-- cdns,read-delay : Delay for read capture logic, in clock cycles
-- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
-                  mode chip select outputs are de-asserted between
-		  transactions.
-- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
-                  de-activated and the activation of another.
-- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
-                  transaction and deasserting the device chip select
-		  (qspi_n_ss_out).
-- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
-                  and first bit transfer.
-- resets	: Must contain an entry for each entry in reset-names.
-		  See ../reset/reset.txt for details.
-- reset-names	: Must include either "qspi" and/or "qspi-ocp".
-
-Example:
-
-	qspi: spi@ff705000 {
-		compatible = "cdns,qspi-nor";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0xff705000 0x1000>,
-		      <0xffa00000 0x1000>;
-		interrupts = <0 151 4>;
-		clocks = <&qspi_clk>;
-		cdns,is-decoded-cs;
-		cdns,fifo-depth = <128>;
-		cdns,fifo-width = <4>;
-		cdns,trigger-address = <0x00000000>;
-		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
-		reset-names = "qspi", "qspi-ocp";
-
-		flash0: n25q00@0 {
-			...
-			cdns,read-delay = <4>;
-			cdns,tshsl-ns = <50>;
-			cdns,tsd2d-ns = <50>;
-			cdns,tchsh-ns = <4>;
-			cdns,tslch-ns = <4>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
new file mode 100644
index 000000000000..94d631045153
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
@@ -0,0 +1,153 @@ 
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence Quad SPI controller
+
+maintainers:
+  - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
+  - Brad Larson <brad@pensando.io>
+
+properties:
+  compatible:
+    contains:
+      enum:
+        - cdns,qspi-nor       # Generic default
+        - ti,k2g-qspi         # TI 66AK2G SoC
+        - ti,am654-ospi       # TI AM654 SoC
+        - intel,lgm-qspi      # Intel LGM SoC
+        - pensando,cdns-qspi  # Pensando Elba SoC
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  reg:
+    minItems: 2
+    maxItems: 2
+    description: |
+      Contains two entries, each of which is a tuple consisting of a
+      physical address and length. The first entry is the address and
+      length of the controller register set. The second entry is the
+      address and length of the QSPI Controller data area.
+
+  interrupts:
+    maxItems: 1
+    description: Unit interrupt specifier for the controller interrupt
+
+  clocks:
+    description: phandle to the Quad SPI clock
+
+  cdns,fifo-depth:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Size of the data FIFO in words
+
+  cdns,fifo-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Bus width of the data FIFO in bytes
+
+  cdns,trigger-address:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: 32-bit indirect AHB trigger address
+
+  cdns,is-decoded-cs:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: Flag to indicate whether decoder is used or not
+
+  cdns,rclk-en:
+    description:
+      Flag to indicate that QSPI return clock is used to latch the
+      read data rather than the QSPI clock. Make sure that QSPI return
+      clock is populated on the board before using this property
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  # Subnodes of the Cadence Quad SPI controller are spi slave nodes 
+  # with additional custom properties
+  cdns,read-delay:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Delay for read capture logic, in clock cycles
+
+  cdns,tshsl-ns:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Delay in nanoseconds for the length that the master mode chip
+      select outputs are de-asserted between transactions
+
+  cdns,tsd2d-ns:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Delay in nanoseconds between one chip select being de-activated
+      and the activation of another.
+
+  cdns,tchsh-ns:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Delay in nanoseconds between last bit of current transaction and
+      deasserting the device chip select (qspi_n_ss_out).
+
+  cdns,tslch-ns:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Delay in nanoseconds between setting qspi_n_ss_out low and first
+      bit transfer.
+
+  resets:
+    items:
+      - description: qspi reset
+      - description: qspi-ocp reset
+
+  reset-names:
+    items:
+      - const: qspi
+      - const: qspi-ocp
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - cdns,fifo-depth
+  - cdns,fifo-width
+  - cdns,trigger-address
+
+patternProperties:
+  "^.*@[0-9]+$":
+    type: object
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/reset/altr,rst-mgr-a10.h>
+    qspi: spi@ff705000 {
+        compatible = "cdns,qspi-nor";
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0xff705000 0x1000>,
+              <0xffa00000 0x1000>;
+        interrupts = <0 151 4>;
+        clocks = <&qspi_clk>;
+        cdns,is-decoded-cs;
+        cdns,fifo-depth = <128>;
+        cdns,fifo-width = <4>;
+        cdns,trigger-address = <0x00000000>;
+        resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
+        reset-names = "qspi", "qspi-ocp";
+
+        flash0: mt25q@0 {
+                compatible = "jdec,spi-nor";
+                reg = <0>;
+                spi-max-frequency = <40000000>;
+                spi-rx-bus-width = <2>;
+                m25p,fast-read;
+                cdns,read-delay = <0>;
+                cdns,tshsl-ns = <0>;
+                cdns,tsd2d-ns = <0>;
+                cdns,tchsh-ns = <0>;
+                cdns,tslch-ns = <0>;
+        };
+    };