@@ -2109,5 +2109,24 @@ config SGI_MFD_IOC3
If you have an SGI Origin, Octane, or a PCI IOC3 card,
then say Y. Otherwise say N.
+config MFD_SL28CPLD
+ bool "Kontron sl28 core driver"
+ depends on I2C=y
+ depends on OF
+ select REGMAP_I2C
+ select MFD_CORE
+ help
+ This option enables support for the board management controller
+ found on the Kontron sl28 CPLD. You have to select individual
+ functions, such as watchdog, GPIO, etc, under the corresponding menus
+ in order to enable them.
+
+ Currently supported boards are:
+
+ Kontron SMARC-sAL28
+
+ To compile this driver as a module, choose M here: the module will be
+ called sl28cpld.
+
endmenu
endif
@@ -264,3 +264,5 @@ obj-$(CONFIG_MFD_ROHM_BD718XX) += rohm-bd718x7.o
obj-$(CONFIG_MFD_STMFX) += stmfx.o
obj-$(CONFIG_SGI_MFD_IOC3) += ioc3.o
+
+obj-$(CONFIG_MFD_SL28CPLD) += sl28cpld.o
new file mode 100644
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * MFD core for the sl28cpld.
+ *
+ * Copyright 2019 Kontron Europe GmbH
+ */
+
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/regmap.h>
+
+#define SL28CPLD_VERSION 0x03
+#define SL28CPLD_MIN_REQ_VERSION 14
+
+struct sl28cpld {
+ struct device *dev;
+ struct regmap *regmap;
+};
+
+static const struct regmap_config sl28cpld_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .reg_stride = 1,
+};
+
+static int sl28cpld_probe(struct i2c_client *i2c)
+{
+ struct sl28cpld *sl28cpld;
+ struct device *dev = &i2c->dev;
+ unsigned int cpld_version;
+ int ret;
+
+ sl28cpld = devm_kzalloc(dev, sizeof(*sl28cpld), GFP_KERNEL);
+ if (!sl28cpld)
+ return -ENOMEM;
+
+ sl28cpld->regmap = devm_regmap_init_i2c(i2c, &sl28cpld_regmap_config);
+ if (IS_ERR(sl28cpld->regmap))
+ return PTR_ERR(sl28cpld->regmap);
+
+ ret = regmap_read(sl28cpld->regmap, SL28CPLD_VERSION, &cpld_version);
+ if (ret)
+ return ret;
+
+ if (cpld_version < SL28CPLD_MIN_REQ_VERSION) {
+ dev_err(dev, "unsupported CPLD version %d\n", cpld_version);
+ return -ENODEV;
+ }
+
+ sl28cpld->dev = dev;
+ i2c_set_clientdata(i2c, sl28cpld);
+
+ dev_info(dev, "successfully probed. CPLD version %d\n", cpld_version);
+
+ return devm_of_platform_populate(&i2c->dev);
+}
+
+static const struct of_device_id sl28cpld_of_match[] = {
+ { .compatible = "kontron,sl28cpld-r1", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sl28cpld_of_match);
+
+static struct i2c_driver sl28cpld_driver = {
+ .probe_new = sl28cpld_probe,
+ .driver = {
+ .name = "sl28cpld",
+ .of_match_table = of_match_ptr(sl28cpld_of_match),
+ },
+};
+module_i2c_driver(sl28cpld_driver);
+
+MODULE_DESCRIPTION("sl28cpld MFD Core Driver");
+MODULE_AUTHOR("Michael Walle <michael@walle.cc>");
+MODULE_LICENSE("GPL");
Add the core support for the board management controller found on the SMARC-sAL28 board. It consists of the following functions: - watchdog - GPIO controller - PWM controller - fan sensor - interrupt controller At the moment, this controller is used on the Kontron SMARC-sAL28 board. Please note that the MFD driver is defined as bool in the Kconfig because the next patch will add interrupt support. Signed-off-by: Michael Walle <michael@walle.cc> --- drivers/mfd/Kconfig | 19 ++++++++++ drivers/mfd/Makefile | 2 ++ drivers/mfd/sl28cpld.c | 79 ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 100 insertions(+) create mode 100644 drivers/mfd/sl28cpld.c