@@ -8,6 +8,7 @@
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "hi3670.dtsi"
#include "hikey970-pinctrl.dtsi"
@@ -17,6 +18,8 @@
compatible = "hisilicon,hi3670-hikey970", "hisilicon,hi3670";
aliases {
+ mshc1 = &dwmmc1;
+ mshc2 = &dwmmc2;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
@@ -35,6 +38,37 @@
/* expect bootloader to fill in this region */
reg = <0x0 0x0 0x0 0x0>;
};
+
+ sd_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ sd_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ wlan_en: wlan-en-1-8v {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ /* GPIO_051_WIFI_EN */
+ gpio = <&gpio6 3 0>;
+
+ /* WLAN card specific delay */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
};
/*
@@ -354,6 +388,47 @@
"GPIO_231_HDMI_INT";
};
+&dwmmc1 {
+ bus-width = <0x4>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ cap-sd-highspeed;
+ disable-wp;
+ cd-inverted;
+ cd-gpios = <&gpio25 5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd_pmx_func
+ &sd_clk_cfg_func
+ &sd_cfg_func>;
+ vmmc-supply = <&sd_3v3>;
+ vqmmc-supply = <&sd_1v8>;
+ status = "okay";
+};
+
+&dwmmc2 { /* WIFI */
+ bus-width = <0x4>;
+ non-removable;
+ broken-cd;
+ cap-power-off-card;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio_pmx_func
+ &sdio_clk_cfg_func
+ &sdio_cfg_func>;
+ /* WL_EN */
+ vmmc-supply = <&wlan_en>;
+ status = "ok";
+
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1837";
+ reg = <2>; /* sdio func num */
+ /* WL_IRQ, GPIO_177_WL_WAKEUP_AP */
+ interrupt-parent = <&gpio22>;
+ interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
&uart0 {
/* On High speed expansion header */
label = "HS-UART0";
@@ -196,6 +196,16 @@
/* pin base, nr pins & gpio function */
pinctrl-single,gpio-range = <&range 0 10 0>;
+ sdio_pmx_func: sdio_pmx_func {
+ pinctrl-single,pins = <
+ 0x000 MUX_M1 /* SDIO_CLK */
+ 0x004 MUX_M1 /* SDIO_CMD */
+ 0x008 MUX_M1 /* SDIO_DATA0 */
+ 0x00c MUX_M1 /* SDIO_DATA1 */
+ 0x010 MUX_M1 /* SDIO_DATA2 */
+ 0x014 MUX_M1 /* SDIO_DATA3 */
+ >;
+ };
};
pmx6: pinmux@fc182800 {
@@ -203,6 +213,52 @@
reg = <0x0 0xfc182800 0x0 0x028>;
#pinctrl-cells = <1>;
pinctrl-single,register-width = <0x20>;
+
+ sdio_clk_cfg_func: sdio_clk_cfg_func {
+ pinctrl-single,pins = <
+ 0x000 0x0 /* SDIO_CLK */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE6_32MA DRIVE6_MASK
+ >;
+ };
+
+ sdio_cfg_func: sdio_cfg_func {
+ pinctrl-single,pins = <
+ 0x004 0x0 /* SDIO_CMD */
+ 0x008 0x0 /* SDIO_DATA0 */
+ 0x00c 0x0 /* SDIO_DATA1 */
+ 0x010 0x0 /* SDIO_DATA2 */
+ 0x014 0x0 /* SDIO_DATA3 */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE6_19MA DRIVE6_MASK
+ >;
+ };
};
pmx7: pinmux@ff37e000 {
@@ -214,6 +270,17 @@
pinctrl-single,function-mask = <7>;
/* pin base, nr pins & gpio function */
pinctrl-single,gpio-range = <&range 0 12 0>;
+
+ sd_pmx_func: sd_pmx_func {
+ pinctrl-single,pins = <
+ 0x000 MUX_M1 /* SD_CLK */
+ 0x004 MUX_M1 /* SD_CMD */
+ 0x008 MUX_M1 /* SD_DATA0 */
+ 0x00c MUX_M1 /* SD_DATA1 */
+ 0x010 MUX_M1 /* SD_DATA2 */
+ 0x014 MUX_M1 /* SD_DATA3 */
+ >;
+ };
};
pmx8: pinmux@ff37e800 {
@@ -221,6 +288,54 @@
reg = <0x0 0xff37e800 0x0 0x030>;
#pinctrl-cells = <1>;
pinctrl-single,register-width = <0x20>;
+
+ sd_clk_cfg_func: sd_clk_cfg_func {
+ pinctrl-single,pins = <
+ 0x000 0x0 /* SD_CLK */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_DIS
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE6_32MA
+ DRIVE6_MASK
+ >;
+ };
+
+ sd_cfg_func: sd_cfg_func {
+ pinctrl-single,pins = <
+ 0x004 0x0 /* SD_CMD */
+ 0x008 0x0 /* SD_DATA0 */
+ 0x00c 0x0 /* SD_DATA1 */
+ 0x010 0x0 /* SD_DATA2 */
+ 0x014 0x0 /* SD_DATA3 */
+ >;
+ pinctrl-single,bias-pulldown = <
+ PULL_DIS
+ PULL_DOWN
+ PULL_DIS
+ PULL_DOWN
+ >;
+ pinctrl-single,bias-pullup = <
+ PULL_UP
+ PULL_UP
+ PULL_DIS
+ PULL_UP
+ >;
+ pinctrl-single,drive-strength = <
+ DRIVE6_19MA
+ DRIVE6_MASK
+ >;
+ };
};
pmx1: pinmux@fff11000 {
Add SD and WiFi support for HiKey970 board based on HI3670 SoC. Due to the absence of the PMIC driver, fixed regulators are sourced to make the driver working. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- .../boot/dts/hisilicon/hi3670-hikey970.dts | 75 ++++++++++++ .../boot/dts/hisilicon/hikey970-pinctrl.dtsi | 115 ++++++++++++++++++ 2 files changed, 190 insertions(+) -- 2.17.1