| Message ID | cover.1561094029.git.baolin.wang@linaro.org |
|---|---|
| Headers | show |
| Series | Optimize voltage switch for the SD controller | expand |
On 21/06/19 9:12 AM, Baolin Wang wrote: > For Spreadtrum SD host controller, we can not use standard SD registers > to change and detect the I/O voltage signals, since our voltage regulator > for I/O is fixed in hardware, and no signals were connected to the SD > controller. Thus add Spreadtrum specific voltage switch ops to change > voltage instead of using standard SD host registers. > > Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> > --- > drivers/mmc/host/sdhci-sprd.c | 24 ++++++++++++++++++++++++ > 1 file changed, 24 insertions(+) > > diff --git a/drivers/mmc/host/sdhci-sprd.c b/drivers/mmc/host/sdhci-sprd.c > index 024c3c5..8b23c88 100644 > --- a/drivers/mmc/host/sdhci-sprd.c > +++ b/drivers/mmc/host/sdhci-sprd.c > @@ -403,6 +403,22 @@ static void sdhci_sprd_request(struct mmc_host *mmc, struct mmc_request *mrq) > sdhci_request(mmc, mrq); > } > > +static int sdhci_sprd_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios) > +{ > + int ret; > + > + if (!IS_ERR(mmc->supply.vqmmc)) { > + ret = mmc_regulator_set_vqmmc(mmc, ios); > + if (ret) { > + pr_err("%s: Switching signalling voltage failed\n", > + mmc_hostname(mmc)); > + return ret; > + } > + } > + > + return 0; > +} > + > static void sdhci_sprd_hs400_enhanced_strobe(struct mmc_host *mmc, > struct mmc_ios *ios) > { > @@ -470,6 +486,14 @@ static int sdhci_sprd_probe(struct platform_device *pdev) > host->mmc_host_ops.request = sdhci_sprd_request; > host->mmc_host_ops.hs400_enhanced_strobe = > sdhci_sprd_hs400_enhanced_strobe; > + /* > + * We can not use the standard ops to change and detect the voltage > + * signal for Spreadtrum SD host controller, since our voltage regulator > + * for I/O is fixed in hardware, that means we do not need control > + * the standard SD host controller to change the I/O voltage. > + */ > + host->mmc_host_ops.start_signal_voltage_switch = > + sdhci_sprd_voltage_switch; > > host->mmc->caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED | > MMC_CAP_ERASE | MMC_CAP_CMD23; >
On Fri, 21 Jun 2019 at 08:12, Baolin Wang <baolin.wang@linaro.org> wrote: > > This patch set is used to optimize voltage switch for the > Spreadtrum SD host controller. > > Any comments are welcome. Thanks. > > Baolin Wang (3): > mmc: sdhci-sprd: Add start_signal_voltage_switch ops > dt-bindings: mmc: sprd: Add pinctrl support > mmc: sdhci-sprd: Add pin control support for voltage switch > > .../devicetree/bindings/mmc/sdhci-sprd.txt | 7 ++ > drivers/mmc/host/sdhci-sprd.c | 78 ++++++++++++++++++++ > 2 files changed, 85 insertions(+) > > -- > 1.7.9.5 > Applied for next, thanks! Kind regards Uffe