[0/5] hwmon: (nct6775) Add i2c support

Message ID	20220226133047.6226-1-zev@bewilderbeest.net
Headers	show Return-Path: <devicetree-owner@kernel.org> sender: zev) by thorn.bewilderbeest.net (Postfix) with ESMTPSA id 1338A3BA; Sat, 26 Feb 2022 05:30:59 -0800 (PST) From: Zev Weiss <zev@bewilderbeest.net> To: linux-hwmon@vger.kernel.org, Guenter Roeck <linux@roeck-us.net>, Jean Delvare <jdelvare@suse.com> Cc: Zev Weiss <zev@bewilderbeest.net>, openbmc@lists.ozlabs.org, linux-kernel@vger.kernel.org, Renze Nicolai <renze@rnplus.nl>, Rob Herring <robh+dt@kernel.org>, devicetree@vger.kernel.org Subject: [PATCH 0/5] hwmon: (nct6775) Add i2c support Date: Sat, 26 Feb 2022 05:30:42 -0800 Message-Id: <20220226133047.6226-1-zev@bewilderbeest.net> MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Precedence: bulk
Series	hwmon: (nct6775) Add i2c support \| expand [0/5] hwmon: (nct6775) Add i2c support [4/5] dt-bindings: hwmon: Add nuvoton,nct6775

[Adding Denis re: wmi discussion below...] On Sat, Feb 26, 2022 at 03:54:42PM PST, Guenter Roeck wrote: >On 2/26/22 05:30, Zev Weiss wrote: >>Hello, >> >>This patch series augments the existing nct6775 driver with support >>for the hardware's i2c interface. >> >>Thus far the nct6775 driver has only supported the LPC interface, >>which is the main interface by which the Super-I/O chip is typically >>connected to the host (x86) processor. >> >>However, these chips also provide an i2c interface, which can provide >>a way for a BMC to also monitor sensor readings from them. On some >>systems (such as the ASRock Rack ROMED8HM3 and X570-D4U) this may be >>the only way for the BMC to monitor host CPU temperatures (e.g. to >>indirectly access a TSI interface); this functionality is thus an >>important component of enabling OpenBMC to support such systems. >> >>In such an arrangement the Super-I/O chip is simultaneously controlled >>by two independent processors (the host and the BMC) which typically >>do not coordinate their accesses with each other. In order to avoid >>conflicts between the two, the i2c driver avoids all writes to the >>device, since the BMC's needs with the hardware are merely that it be >>able to retrieve sensor readings. This allows the host processor to >>remain ultimately in control of the chip and unaware of the BMC's use >>of it at all. >> >>The sole exception to the "no writes" rule for the i2c driver is for >>the bank-select register -- while I haven't been able to find any >>explicit statement in the Nuvoton datasheets guaranteeing this, all >>experiments I've done have indicated that, as one might hope, the i2c >>interface has its own bank-select register independent of the one used >>by the LPC interface. >> > >That will a more detailed confirmation. Please explain in detail >the experiments you have done. > >Other chips (specifically those served by the it87 driver) have the >same problem, and there it was never really solved. That resulted >in random crashes. I don't want to end up in the same situation. > On an ASRock Rack ROMED8HM3, I used the following program to manually peek and poke device registers from the host: host# cat port.c #include <stdlib.h> #include <string.h> #include <stdio.h> #include <sys/io.h> int main(int argc, char** argv) { unsigned long addr, val; if (iopl(3)) { perror("iopl"); exit(1); } if (argc == 3 && !strcmp(argv[1], "r")) { addr = strtoul(argv[2], NULL, 0); printf("%03lx: %02x\n", addr, inb(addr)); } else if (argc == 4 && !strcmp(argv[1], "w")) { addr = strtoul(argv[2], NULL, 0); val = strtoul(argv[3], NULL, 0); printf("%03lx <- %02lx\n", addr, val); outb(val, addr); } else { fprintf(stderr, "Usage: %s [rw] ADDR [VALUE]\n", argv[0]); exit(1); } return 0; } host# cc -o port port.c At the same time, I used i2cget & i2cset to do the same from the BMC (the nct6779 is at address 0x2d on bus 1). Interleaving some shell transcripts chronologically (no drivers bound on either processor): host# ./port w 0x295 0x4e && ./port r 0x296 295 <- 4e 296: 08 bmc# i2cget -y 1 0x2d 0x4e 0x02 bmc# i2cset -y 1 0x2d 0x4e 0x01 bmc# i2cget -y 1 0x2d 0x4e 0x01 host# ./port w 0x295 0x4e && ./port r 0x296 295 <- 4e 296: 08 So, starting from an initial state where the two sides were reporting different values for the bank select register, a write to the bank select register via the BMC's i2c interface is seen by a subsequent read over that same interface, but the host still sees the same value it saw initially. Reversing the roles (host writing the bank-select register), the BMC is likewise unaffected: bmc# i2cget -y 1 0x2d 0x4e 0x01 host# ./port w 0x295 0x4e && ./port r 0x296 295 <- 4e 296: 08 host# ./port w 0x295 0x4e && ./port w 0x296 0x06 295 <- 4e 296 <- 06 host# ./port w 0x295 0x4e && ./port r 0x296 295 <- 4e 296: 06 bmc# i2cget -y 1 0x2d 0x4e 0x01 In contrast, looking at a different read/write register (the config register at 0x40 in bank 0, for example), writes from each side are seen by the other: host# ./port w 0x295 0x4e && ./port w 0x296 0x00 295 <- 4e 296 <- 00 host# ./port w 0x295 0x40 && ./port r 0x296 295 <- 40 296: 03 bmc# i2cset -y 1 0x2d 0x4e 0x00 bmc# i2cget -y 1 0x2d 0x40 0x03 bmc# i2cset -y 1 0x2d 0x40 0x01 bmc# i2cget -y 1 0x2d 0x40 0x01 host# ./port w 0x295 0x40 && ./port r 0x296 295 <- 40 296: 01 host# ./port w 0x295 0x40 && ./port w 0x296 0x03 295 <- 40 296 <- 03 host# ./port w 0x295 0x40 && ./port r 0x296 295 <- 40 296: 03 bmc# i2cget -y 1 0x2d 0x40 0x03 To be cautious we could perhaps trim down the list of supported chips in the i2c driver to include only the models that are known to pass tests like the above; I can certainly make that change if that would be preferred. >>In terms of code structure, the approach taken in this series is to >>split the LPC-specific parts of the driver out into a separate module >>(called nct6775-platform), leaving the interface-independent parts in >>a generic driver (called nct6775-core). The nct6775-i2c driver is >>then added as an additional consumer of the nct6775-core module's >>functionality. >> > >How about wmi ? Shouldn't that be separated as well ? > I admittedly don't know much about wmi, but from what I could see in the code it looked to me like it essentially just acts as an alternate software/firmware path to the same underlying LPC interface, so I figured it would make sense to leave it integrated with the rest of the platform driver as it is currently. If there's a particular benefit to be gained from splitting it out as well I can look into doing so, but from my current understanding it seems like it would lead to either: - duplication between the wmi and bare inb/outb versions of the platform driver, or - to eliminate the duplication, a third (intermediate) module containing the code that was common to the two of them, leaving the two platform driver modules as little else than the bare register I/O routines (superio_[wmi_]inb, nct6775_[wmi_]read_value, etc.), i.e. the differences that are already handled via the indirection of the function pointers Denis added recently. I suppose the hypothetical intermediate module in the second scenario above could also be integrated back into nct6775-core, though that part of it would then be needless dead weight for the typically more resource-constrained systems (e.g. BMCs) that are only going to use the i2c driver. Anyway, none of the above possibilities seemed terribly appealing to me, but if there's something I've misunderstood or factors I haven't taken into account please let me know. Thanks, Zev

[0/5] hwmon: (nct6775) Add i2c support

Message

Comments