@@ -113,6 +113,7 @@ config BT_HCIUART_SERDEV
config BT_HCIUART_H4
bool "UART (H4) protocol support"
depends on BT_HCIUART
+ depends on BT_HCIUART_SERDEV
help
UART (H4) is serial protocol for communication between Bluetooth
device and host. This protocol is required for most Bluetooth devices
@@ -18,6 +18,8 @@
#include <linux/ptrace.h>
#include <linux/poll.h>
+#include <linux/of.h>
+#include <linux/serdev.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/errno.h>
@@ -32,6 +34,10 @@
#include "hci_uart.h"
+struct h4_device {
+ struct hci_uart hu;
+};
+
struct h4_struct {
struct sk_buff *rx_skb;
struct sk_buff_head txq;
@@ -130,6 +136,63 @@ static struct sk_buff *h4_dequeue(struct hci_uart *hu)
return skb_dequeue(&h4->txq);
}
+static const struct hci_uart_proto h4p;
+
+static int h4_probe(struct serdev_device *serdev)
+{
+ struct h4_device *h4dev;
+ struct hci_uart *hu;
+ int ret;
+ u32 speed;
+
+ h4dev = devm_kzalloc(&serdev->dev, sizeof(*h4dev), GFP_KERNEL);
+ if (!h4dev)
+ return -ENOMEM;
+
+ hu = &h4dev->hu;
+
+ hu->serdev = serdev;
+ ret = device_property_read_u32(&serdev->dev, "max-speed", &speed);
+ if (!ret) {
+ /* h4 does not have any baudrate handling:
+ * user oper speed from the start
+ */
+ hu->init_speed = speed;
+ hu->oper_speed = speed;
+ }
+
+ serdev_device_set_drvdata(serdev, h4dev);
+ dev_info(&serdev->dev, "h4 device registered.\n");
+
+ return hci_uart_register_device(hu, &h4p);
+}
+
+static void h4_remove(struct serdev_device *serdev)
+{
+ struct h4_device *h4dev = serdev_device_get_drvdata(serdev);
+
+ dev_info(&serdev->dev, "h4 device unregistered.\n");
+
+ hci_uart_unregister_device(&h4dev->hu);
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id h4_bluetooth_of_match[] = {
+ { .compatible = "nxp,aw-xm458-bt" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, h4_bluetooth_of_match);
+#endif
+
+static struct serdev_device_driver h4_serdev_driver = {
+ .probe = h4_probe,
+ .remove = h4_remove,
+ .driver = {
+ .name = "hci_uart_h4",
+ .of_match_table = of_match_ptr(h4_bluetooth_of_match),
+ },
+};
+
static const struct hci_uart_proto h4p = {
.id = HCI_UART_H4,
.name = "H4",
@@ -143,11 +206,13 @@ static const struct hci_uart_proto h4p = {
int __init h4_init(void)
{
+ serdev_device_driver_register(&h4_serdev_driver);
return hci_uart_register_proto(&h4p);
}
int __exit h4_deinit(void)
{
+ serdev_device_driver_unregister(&h4_serdev_driver);
return hci_uart_unregister_proto(&h4p);
}
adding serdev support to hci_h4 allows users to define h4 bluetooth controllers in dts files This allows users of bluetooth modules with an uart h4 interface to use dt bindings instead of manually running btattach Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com> --- drivers/bluetooth/Kconfig | 1 + drivers/bluetooth/hci_h4.c | 65 ++++++++++++++++++++++++++++++++++++++ 2 files changed, 66 insertions(+)