@@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandmax.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandprimelte.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-gt510.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-gt58.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j3ltetw.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5x.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-rossa.dtb
new file mode 100644
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8916-samsung-j5-common.dtsi"
+
+/ {
+ reserved-memory {
+ /delete-node/ tz-apps@85500000;
+
+ /* Additional memory used by Samsung firmware modifications */
+ tz-apps@85800000 {
+ reg = <0x0 0x85800000 0x0 0x800000>;
+ no-map;
+ };
+ };
+
+ reg_vdd_tsp_a: regulator-vdd-tsp-a {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_tsp_a";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+
+ gpio = <&tlmm 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&tsp_ldo_en_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&gpio_hall_sensor {
+ status = "disabled";
+};
+
+&i2c_muic {
+ /* GPIO pins vary depending on model variant */
+};
+
+&i2c_sensors {
+ /* GPIO pins vary depending on model variant */
+};
+
+&touchscreen {
+ vdd-supply = <®_vdd_tsp_a>;
+};
+
+&tlmm {
+ tsp_ldo_en_default: tsp-ldo-en-default-state {
+ pins = "gpio16";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
new file mode 100644
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-j3-common.dtsi"
+
+/ {
+ model = "Samsung Galaxy J3 (2016) (SM-J320YZ)";
+ compatible = "samsung,j3ltetw", "qcom,msm8916";
+ chassis-type = "handset";
+};
+
+&i2c_muic {
+ sda-gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&tlmm 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+};
+
+&muic_i2c_default {
+ pins = "gpio0", "gpio1";
+};
The dts and dtsi add support for msm8916 variant of Samsung Galaxy J3 SM-J320YZ smartphone released in 2016. Add a device tree for SM-J320YZ with initial support for: - GPIO keys - SDHCI (internal and external storage) - USB Device Mode - UART (on USB connector via the SM5703 MUIC) - WCNSS (WiFi/BT) - Regulators - QDSP6 audio - Speaker/earpiece/headphones/microphones via digital/analog codec in MSM8916/PM8916 - WWAN Internet via BAM-DMUX - Touchscreen There are different variants of J3, with some differences in MUIC, sensor, NFC and touch key I2C buses. The common parts are shared in msm8916-samsung-j3-common.dtsi to reduce duplication. Signed-off-by: "Lin, Meng-Bo" <linmengbo06890@proton.me> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../dts/qcom/msm8916-samsung-j3-common.dtsi | 53 +++++++++++++++++++ .../boot/dts/qcom/msm8916-samsung-j3ltetw.dts | 20 +++++++ 3 files changed, 74 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-j3-common.dtsi create mode 100644 arch/arm64/boot/dts/qcom/msm8916-samsung-j3ltetw.dts