| Message ID | 20240525-sc8180x-usb-mp-v1-8-60a904392438@quicinc.com |
|---|---|
| State | Accepted |
| Commit | 96aab8ff59a9fca54dd0e13660684b4a8e73e1a3 |
| Headers | show |
| Series | arm64: dts: qcom: sc8180x: Enable the USB multiport controller | expand |
On 5/25/24 20:04, Bjorn Andersson wrote: > From: Bjorn Andersson <quic_bjorande@quicinc.com> > > The SC8180X platform comes with a multiport DWC3 controller with two > ports, each connected to a pair of HighSpeed and QMP SuperSpeed PHYs. > > Describe these blocks. > > Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> > --- > arch/arm64/boot/dts/qcom/sc8180x.dtsi | 146 ++++++++++++++++++++++++++++++++++ > 1 file changed, 146 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc8180x.dtsi b/arch/arm64/boot/dts/qcom/sc8180x.dtsi > index 9ef3fa40e1d8..0950dc7adb20 100644 > --- a/arch/arm64/boot/dts/qcom/sc8180x.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc8180x.dtsi > @@ -2511,6 +2511,34 @@ usb_sec_hsphy: phy@88e3000 { > status = "disabled"; > }; > > + usb_mp0_hsphy: phy@88e4000 { Even though the register names are MPn, I think this is a bit confusing.. There's only one MP controller, so perhaps usb_mp_hsphy0? [...] > + clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>, > + <&gcc GCC_USB3_PRIM_CLKREF_CLK>, > + <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>, > + <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>; PIPE_1_CLK > + clock-names = "aux", "ref", "com_aux", "pipe"; This could be a vertical list > + > + resets = <&gcc GCC_USB3_UNIPHY_MP1_BCR>, > + <&gcc GCC_USB3UNIPHY_PHY_MP1_BCR>; > + reset-names = "phy", "phy_phy"; > + > + power-domains = <&gcc USB30_MP_GDSC>; > + > + #clock-cells = <0>; > + clock-output-names = "usb2_phy1_pipe_clk"; > + > + #phy-cells = <0>; > + > + status = "disabled"; > + }; > + > usb_sec_qmpphy: phy@88ee000 { > compatible = "qcom,sc8180x-qmp-usb3-dp-phy"; > reg = <0 0x088ee000 0 0x18c>, > @@ -2662,6 +2738,76 @@ gem_noc: interconnect@9680000 { > qcom,bcm-voters = <&apps_bcm_voter>; > }; > > + usb_mp: usb@a4f8800 { > + compatible = "qcom,sc8180x-dwc3-mp", "qcom,dwc3"; > + reg = <0 0x0a4f8800 0 0x400>; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + dma-ranges; > + > + clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>, > + <&gcc GCC_USB30_MP_MASTER_CLK>, > + <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>, > + <&gcc GCC_USB30_MP_SLEEP_CLK>, > + <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>, > + <&gcc GCC_USB3_SEC_CLKREF_CLK>; This is used by the secondary DWC3 (non-MP). Are you sure? Actually, are we sure that these clocks are really supplying the DWC3s? > + clock-names = "cfg_noc", > + "core", > + "iface", > + "sleep", > + "mock_utmi", > + "xo"; > + > + interconnects = <&aggre1_noc MASTER_USB3_2 0 &mc_virt SLAVE_EBI_CH0 0>, > + <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3_2 0>; > + interconnect-names = "usb-ddr", "apps-usb"; > + > + assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>, > + <&gcc GCC_USB30_MP_MASTER_CLK>; > + assigned-clock-rates = <19200000>, <200000000>; > + > + interrupts-extended = <&intc GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>, > + <&intc GIC_SPI 655 IRQ_TYPE_LEVEL_HIGH>, > + <&intc GIC_SPI 658 IRQ_TYPE_LEVEL_HIGH>, > + <&intc GIC_SPI 657 IRQ_TYPE_LEVEL_HIGH>, > + <&pdc 59 IRQ_TYPE_EDGE_BOTH>, > + <&pdc 46 IRQ_TYPE_EDGE_BOTH>, > + <&pdc 71 IRQ_TYPE_EDGE_BOTH>, > + <&pdc 68 IRQ_TYPE_EDGE_BOTH>, > + <&pdc 7 IRQ_TYPE_LEVEL_HIGH>, > + <&pdc 30 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "pwr_event_1", "pwr_event_2", > + "hs_phy_1", "hs_phy_2", > + "dp_hs_phy_1", "dm_hs_phy_1", > + "dp_hs_phy_2", "dm_hs_phy_2", > + "ss_phy_1", "ss_phy_2"; > + > + power-domains = <&gcc USB30_MP_GDSC>; > + > + resets = <&gcc GCC_USB30_MP_BCR>; > + > + status = "disabled"; > + > + usb_mp_dwc3: usb@a400000 { > + compatible = "snps,dwc3"; > + reg = <0 0x0a400000 0 0xcd00>; > + interrupts = <GIC_SPI 654 IRQ_TYPE_LEVEL_HIGH>; > + iommus = <&apps_smmu 0x60 0>; > + snps,dis_u2_susphy_quirk; > + snps,dis_enblslpm_quirk; sa8195-usb.dtsi lists a bunch more fluff: snps,has-lpm-erratum; snps,hird-threshold = /bits/ 8 <0x0>; snps,is-utmi-l1-suspend; snps,ssp-u3-u0-quirk; snps,dis-u1-entry-quirk; snps,dis-u2-entry-quirk; snps,dis_u3_susphy_quirk; snps,force-gen1; maximum-speed = "super-speed"; the irq numbers look good Konrad
diff --git a/arch/arm64/boot/dts/qcom/sc8180x.dtsi b/arch/arm64/boot/dts/qcom/sc8180x.dtsi index 9ef3fa40e1d8..0950dc7adb20 100644 --- a/arch/arm64/boot/dts/qcom/sc8180x.dtsi +++ b/arch/arm64/boot/dts/qcom/sc8180x.dtsi @@ -2511,6 +2511,34 @@ usb_sec_hsphy: phy@88e3000 { status = "disabled"; }; + usb_mp0_hsphy: phy@88e4000 { + compatible = "qcom,sc8180x-usb-hs-phy", + "qcom,usb-snps-hs-7nm-phy"; + reg = <0 0x088e4000 0 0x400>; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_MP0_BCR>; + + status = "disabled"; + }; + + usb_mp1_hsphy: phy@88e5000 { + compatible = "qcom,sc8180x-usb-hs-phy", + "qcom,usb-snps-hs-7nm-phy"; + reg = <0 0x088e5000 0 0x400>; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_MP1_BCR>; + + status = "disabled"; + }; + usb_prim_qmpphy: phy@88e9000 { compatible = "qcom,sc8180x-qmp-usb3-dp-phy"; reg = <0 0x088e9000 0 0x18c>, @@ -2577,6 +2605,54 @@ usb_prim_dpphy: dp-phy@88ea200 { }; }; + usb_mp0_qmpphy: phy@88eb000 { + compatible = "qcom,sc8180x-qmp-usb3-uni-phy"; + reg = <0 0x088eb000 0 0x1000>; + + clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>, + <&gcc GCC_USB3_PRIM_CLKREF_CLK>, + <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>, + <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>; + clock-names = "aux", "ref", "com_aux", "pipe"; + + resets = <&gcc GCC_USB3_UNIPHY_MP0_BCR>, + <&gcc GCC_USB3UNIPHY_PHY_MP0_BCR>; + reset-names = "phy", "phy_phy"; + + power-domains = <&gcc USB30_MP_GDSC>; + + #clock-cells = <0>; + clock-output-names = "usb2_phy0_pipe_clk"; + + #phy-cells = <0>; + + status = "disabled"; + }; + + usb_mp1_qmpphy: phy@88ec000 { + compatible = "qcom,sc8180x-qmp-usb3-uni-phy"; + reg = <0 0x088ec000 0 0x1000>; + + clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>, + <&gcc GCC_USB3_PRIM_CLKREF_CLK>, + <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>, + <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>; + clock-names = "aux", "ref", "com_aux", "pipe"; + + resets = <&gcc GCC_USB3_UNIPHY_MP1_BCR>, + <&gcc GCC_USB3UNIPHY_PHY_MP1_BCR>; + reset-names = "phy", "phy_phy"; + + power-domains = <&gcc USB30_MP_GDSC>; + + #clock-cells = <0>; + clock-output-names = "usb2_phy1_pipe_clk"; + + #phy-cells = <0>; + + status = "disabled"; + }; + usb_sec_qmpphy: phy@88ee000 { compatible = "qcom,sc8180x-qmp-usb3-dp-phy"; reg = <0 0x088ee000 0 0x18c>, @@ -2662,6 +2738,76 @@ gem_noc: interconnect@9680000 { qcom,bcm-voters = <&apps_bcm_voter>; }; + usb_mp: usb@a4f8800 { + compatible = "qcom,sc8180x-dwc3-mp", "qcom,dwc3"; + reg = <0 0x0a4f8800 0 0x400>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + dma-ranges; + + clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>, + <&gcc GCC_USB30_MP_MASTER_CLK>, + <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>, + <&gcc GCC_USB30_MP_SLEEP_CLK>, + <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>, + <&gcc GCC_USB3_SEC_CLKREF_CLK>; + clock-names = "cfg_noc", + "core", + "iface", + "sleep", + "mock_utmi", + "xo"; + + interconnects = <&aggre1_noc MASTER_USB3_2 0 &mc_virt SLAVE_EBI_CH0 0>, + <&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3_2 0>; + interconnect-names = "usb-ddr", "apps-usb"; + + assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_MP_MASTER_CLK>; + assigned-clock-rates = <19200000>, <200000000>; + + interrupts-extended = <&intc GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>, + <&intc GIC_SPI 655 IRQ_TYPE_LEVEL_HIGH>, + <&intc GIC_SPI 658 IRQ_TYPE_LEVEL_HIGH>, + <&intc GIC_SPI 657 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 59 IRQ_TYPE_EDGE_BOTH>, + <&pdc 46 IRQ_TYPE_EDGE_BOTH>, + <&pdc 71 IRQ_TYPE_EDGE_BOTH>, + <&pdc 68 IRQ_TYPE_EDGE_BOTH>, + <&pdc 7 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "pwr_event_1", "pwr_event_2", + "hs_phy_1", "hs_phy_2", + "dp_hs_phy_1", "dm_hs_phy_1", + "dp_hs_phy_2", "dm_hs_phy_2", + "ss_phy_1", "ss_phy_2"; + + power-domains = <&gcc USB30_MP_GDSC>; + + resets = <&gcc GCC_USB30_MP_BCR>; + + status = "disabled"; + + usb_mp_dwc3: usb@a400000 { + compatible = "snps,dwc3"; + reg = <0 0x0a400000 0 0xcd00>; + interrupts = <GIC_SPI 654 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&apps_smmu 0x60 0>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + phys = <&usb_mp0_hsphy>, + <&usb_mp0_qmpphy>, + <&usb_mp1_hsphy>, + <&usb_mp1_qmpphy>; + phy-names = "usb2-0", + "usb3-0", + "usb2-1", + "usb3-1"; + dr_mode = "host"; + }; + }; + usb_prim: usb@a6f8800 { compatible = "qcom,sc8180x-dwc3", "qcom,dwc3"; reg = <0 0x0a6f8800 0 0x400>;