@@ -10,11 +10,13 @@
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
+#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/reset.h>
#include <linux/slab.h>
@@ -56,9 +58,6 @@
/* QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR register bits */
#define IRQ_CLEAR BIT(0)
-/* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
-#define CLAMP_EN BIT(0) /* enables i/o clamp_n */
-
#define PHY_INIT_COMPLETE_TIMEOUT 10000
struct qmp_phy_init_tbl {
@@ -94,7 +93,6 @@ enum qphy_reg_layout {
QPHY_PCS_AUTONOMOUS_MODE_CTRL,
QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR,
QPHY_PCS_POWER_DOWN_CONTROL,
- QPHY_PCS_MISC_CLAMP_ENABLE,
/* Keep last to ensure regs_layout arrays are properly initialized */
QPHY_LAYOUT_SIZE
};
@@ -106,7 +104,6 @@ static const unsigned int qmp_v3_usb3phy_regs_layout[QPHY_LAYOUT_SIZE] = {
[QPHY_PCS_AUTONOMOUS_MODE_CTRL] = QPHY_V3_PCS_AUTONOMOUS_MODE_CTRL,
[QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = QPHY_V3_PCS_LFPS_RXTERM_IRQ_CLEAR,
[QPHY_PCS_POWER_DOWN_CONTROL] = QPHY_V3_PCS_POWER_DOWN_CONTROL,
- [QPHY_PCS_MISC_CLAMP_ENABLE] = QPHY_V3_PCS_MISC_CLAMP_ENABLE,
};
static const unsigned int qmp_v3_usb3phy_regs_layout_qcm2290[QPHY_LAYOUT_SIZE] = {
@@ -369,6 +366,9 @@ struct qmp_usbc {
void __iomem *tx2;
void __iomem *rx2;
+ struct regmap *tcsr_map;
+ u32 vls_clamp_reg;
+
struct clk *pipe_clk;
struct clk_bulk_data *clks;
int num_clks;
@@ -691,7 +691,6 @@ static void qmp_usbc_enable_autonomous_mode(struct qmp_usbc *qmp)
{
const struct qmp_phy_cfg *cfg = qmp->cfg;
void __iomem *pcs = qmp->pcs;
- void __iomem *pcs_misc = qmp->pcs_misc;
u32 intr_mask;
if (qmp->mode == PHY_MODE_USB_HOST_SS ||
@@ -712,19 +711,18 @@ static void qmp_usbc_enable_autonomous_mode(struct qmp_usbc *qmp)
qphy_setbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL], intr_mask);
/* Enable i/o clamp_n for autonomous mode */
- if (pcs_misc && cfg->regs[QPHY_PCS_MISC_CLAMP_ENABLE])
- qphy_clrbits(pcs_misc, cfg->regs[QPHY_PCS_MISC_CLAMP_ENABLE], CLAMP_EN);
+ if (qmp->tcsr_map && qmp->vls_clamp_reg)
+ regmap_write(qmp->tcsr_map, qmp->vls_clamp_reg, 1);
}
static void qmp_usbc_disable_autonomous_mode(struct qmp_usbc *qmp)
{
const struct qmp_phy_cfg *cfg = qmp->cfg;
void __iomem *pcs = qmp->pcs;
- void __iomem *pcs_misc = qmp->pcs_misc;
/* Disable i/o clamp_n on resume for normal mode */
- if (pcs_misc && cfg->regs[QPHY_PCS_MISC_CLAMP_ENABLE])
- qphy_setbits(pcs_misc, cfg->regs[QPHY_PCS_MISC_CLAMP_ENABLE], CLAMP_EN);
+ if (qmp->tcsr_map && qmp->vls_clamp_reg)
+ regmap_write(qmp->tcsr_map, qmp->vls_clamp_reg, 0);
qphy_clrbits(pcs, cfg->regs[QPHY_PCS_AUTONOMOUS_MODE_CTRL],
ARCVR_DTCT_EN | ARCVR_DTCT_EVENT_SEL | ALFPS_DTCT_EN);
@@ -1063,6 +1061,30 @@ static int qmp_usbc_parse_dt(struct qmp_usbc *qmp)
return 0;
}
+static int qmp_usbc_parse_vls_clamp(struct qmp_usbc *qmp)
+{
+ struct of_phandle_args tcsr_args;
+ struct device *dev = qmp->dev;
+ int ret;
+
+ /* for backwards compatibility ignore if there is no property */
+ ret = of_parse_phandle_with_fixed_args(dev->of_node, "qcom,tcsr-reg", 1, 0,
+ &tcsr_args);
+ if (ret == -ENOENT)
+ return 0;
+ else if (ret < 0)
+ return dev_err_probe(dev, ret, "Failed to parse qcom,tcsr-reg\n");
+
+ qmp->tcsr_map = syscon_node_to_regmap(tcsr_args.np);
+ of_node_put(tcsr_args.np);
+ if (IS_ERR(qmp->tcsr_map))
+ return PTR_ERR(qmp->tcsr_map);
+
+ qmp->vls_clamp_reg = tcsr_args.args[0];
+
+ return 0;
+}
+
static int qmp_usbc_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
@@ -1093,6 +1115,10 @@ static int qmp_usbc_probe(struct platform_device *pdev)
if (ret)
return ret;
+ ret = qmp_usbc_parse_vls_clamp(qmp);
+ if (ret)
+ return ret;
+
/* Check for legacy binding with child node. */
np = of_get_child_by_name(dev->of_node, "phy");
if (np) {
The QMP USB PHYs on msm8998, qcm2290 and some other platforms don't have the PCS_MISC_CLAMP_ENABLE register. Instead they need to toggle the register in the TCSR space. Make the new phy-qcom-qmp-usbc driver correctly handle the clamp register. Fixes: a51969fafc82 ("phy: qcom-qmp: Add QMP V3 USB3 PHY support for msm8998") Fixes: 8abe5e778b2c ("phy: qcom-qmp: Add QCM2290 USB3 PHY support") Cc: Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- drivers/phy/qualcomm/phy-qcom-qmp-usbc.c | 48 ++++++++++++++++++++++++-------- 1 file changed, 37 insertions(+), 11 deletions(-)